Viavi T-BERD/MTS 4000 V2 Stücklistenhandbuch

VIAVI Solutions

Quick Card

T-BERD®/MTS 4000v2 Modular Test Set

Real Time Testing with Expert OTDR

This quick card describes how to connect to a fiber under test, configure Expert OTDR settings, run

Real Time tests, and analyze results with a VIAVI T-BERD/MTS 4000v2 and 4100-series OTDR module.

Equipment Requirements:

•T-BERD/MTS-2000 or 4000 with Fiber Optics

Software Release V21.04 or greater

•E4100 Series OTDR Module

•Fiber optic cleaning and inspection tools

•Launch Cable with connectors matching the

OTDR port and Fiber Under Test (a minimum

20-meter Fiber optic patch cable or leash is

recommended)

•Optical Coupler to connect Launch Cable to

Fiber Under Test

Figure 1: Equipment Requirements

The following information is required to complete the test:

•Type of Fiber (Multimode or Single Mode)

•Type of Connectors (SC UPC, SC APC, LC UPC, etc.)

Fiber Inspection Guidelines:

•Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (OTDR Port, Launch

Cable, bulkhead connectors, patch cords, etc.)

•Focus fiber on the screen. If dirty, clean the

end-face.

•If it appears clean, run inspection test.

•If it fails, clean the fiber and re-run inspection

test. Repeat until it passes.

Figure 2: Inspect Before You Connect (IBYC)

Connect Launch Cable to OTDR port:

1. Inspect the OTDR port on top of the test set.

2. Inspect the fiber end face of Launch Cable.

3. Connect Launch Cable to the OTDR port.

Figure 3: OTDR Port Inspection

VIAVI Solutions

Connect to Fiber Under Test (FUT):

The Launch Cable may be connected to the FUT

via an optical patch panel (OPP) or an optical

coupler:

1. If the interface to the FUT is a patch cord,

connect the patch cord to an optical coupler

with the same connector type.

2. Inspect the FUT connected to the coupler or

OPP.

3. Inspect the other fiber end face of the

Launch Cable.

4. Connect the Launch Cable to the coupler or

OPP.

Figure 4: Connecting the Launch Cable to the FUT with a coupler

Figure 5: Connecting the Launch Cable to an OPP

Launch and Configure Expert OTDR:

1. Press the Power button to start the

T-BERD/MTS test instrument.

2. Tap the EXPERT OTDR icon until it is yellow

and highlighted .

3. Tap the Setup soft key

4. Tap Display and set Distance Unit to your

desired unit of measure.

5. Tap Auto-set to configure the OTDR to auto-

configure range, pulse width, and resolution.

Figure 6: Fiber Optics Home screen

Figure 7: Expert OTDR Setup

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest you,

visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

Run Test:

1. Tap the Real Time soft key to start the

test.

2. After auto-configuration, the OTDR will

perform a connection check to ensure that

the connection is Good. If the Connection is

Bad, disconnect the launch cable, and

reconnect as described on pages 1 and 2,

cleaning every end-face that fails the

inspection test.

3. The OTDR will perform real-time acquisitions

at the configured wavelength.

4. Tap the magnifying glass icons to zoom in

, zoom out , or auto-zoom the

display. You can also pinch and zoom with

your fingers.

5. Tap the Measurements soft key to

start Loss, ORL, or Reflectance

measurements.

6. Tap the Test roll down menu at the bottom

left screen to select a measurement type:

Loss, ORL, or Reflectance.

7. Tap and move the Aand Bcursors to change

measurement values.

•Loss and ORL are measured between the

two cursor positions.

•Reflectance is measured at the position

of the Bcursor.

8. Figure 10 shows Loss measurement, Figure

11 shows ORL measurement, and Figure 12

shows Reflectance measurement.

9. Tap the STOP soft key to stop the Real

Time measurement.

10. Tap the Real Time soft key to restart

real time measurement.

Figure 8: Expert OTDR

Figure 9: Connection Check & Real-Time Acquisition

Figure 10: Trace View, Loss Result

Figure 11: Trace View, ORL result

Figure 12: Trace View, Reflectance Result

Andere Handbücher für T-BERD/MTS 4000 V2

Inhaltsverzeichnis

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi T-BERD/MTS-5800 Stücklistenhandbuch

Viavi

Viavi 4100 Series Stücklistenhandbuch

Viavi

Viavi T-BERD 5800 Stücklistenhandbuch

Viavi

Viavi MTS 2000 Stücklistenhandbuch

Viavi

Viavi OSA-4100 Bedienungsanleitung

Viavi

Viavi OneAdvisor ONA-1000 400G Technisches Handbuch

Viavi

Viavi T-BERD/MTS-5800 Stücklistenhandbuch

Viavi

Viavi IFR 6000 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS-5800 Stücklistenhandbuch

Viavi

Viavi FCOMP/-PRO T-BERD/MTS-2000V2 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi OBS-500 Bedienungsanleitung

Viavi

Viavi ONX 580 Bedienungsanleitung

Viavi

Viavi OLP-88 Bedienungsanleitung

Viavi

Viavi OneAdvisor-1000 Bedienungsanleitung

Viavi

Viavi MSQ-900 Bedienungsanleitung

Viavi

Viavi OneAdvisor ONA-800 Bedienungsanleitung

Viavi

Viavi T-BERD MTS-580 Stücklistenhandbuch

Viavi

Viavi SmartOTDR Stücklistenhandbuch

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi SmartClass OLP-85 Series Bedienungsanleitung

Viavi

Viavi OCC-4056 Stücklistenhandbuch

Viavi

Viavi MTS 2000 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung