Vision Fitness E3000 Bedienungsanleitung

Guide

Assembly

E3000, E3100, E3200 & E3200HRT

UPRIGHT FITNESS CYCLES

upright fitness cycles

To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding though,

find your new Fitness Cycle’s serial number located on the front axle tube, and enter here:

Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.

Be sure to read your Owner’s Guide before using your new Fitness Cycle.

If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Fitness Cycle, to prevent

loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before

completely tightening any ONE bolt.

STEP

E3000 E3200HRT

E3100

E3200

STEP

TOOLS & PARTS INCLUDED

5MM Allen Wrench

15MM Pedal Wrench

Screwdriver

5MM L-Shaped Wrench

PARTS BOX

Water Bottle & Bracket, Qty: 1

Heart Rate Chest Strap, Qty: 1 (E3200HRT only)

Power Supply, Qty: 1 (E3200 & E3200HRT only)

Tension Control Knob and bracket, Qty: 1 (E3000 only)

Transport Wheels, Qty: 2 (NOT E3000)

Front Axle, Qty: 1 (NOT E3000)

Pedals, Qty: 2

Seat Post Knob, Qty: 1

Owner’s Guide, Qty: 1

Assembly Guide, Qty: 1

Warranty Card, Qty: 1

14MM Wrench

HARDWARE INCLUDED

ORANGE BAG

PINK BAG

BLUE BAG

M8 x 20L Bolt

Quantity: 2

M8 x 65L Bolt

Quantity: 2

M8 Lock Washer

Quantity: 4

M16 Washer

Quantity: 2

M8 x 19L Bolt

Quantity: 2

M8 Washer

Quantity: 2

M8 x 15L Bolt

Quantity: 7

M8 Lock Washer

Quantity: 8

M8 x 20L Bolt

Quantity: 2

M5 x 70L Screw

Quantity: 1

(E3000 only)

STEP

• Slide the rear foot into place and

secure with two bolts (M8x20L) and

two lock washers (M8) to the outside

holes. Secure with two bolts (M8x65L)

and two lock washers (M8) to the

inside holes. Tighten with the 5MM Allen

wrench.

MODEL E3000 ONLY: Proceed to

Step 3 after completion of Step 1.

ORANGE BAG

STEP

• Slide the front axle into the plastic

sleeve of the front foot. Place a

washer (M16) on each end of the

axle.

• Slide a transport wheel onto each

end of the axle. With the 5MM Allen

wrench, tighten a bolt (M8x19L) and

washer (M8) to each end of the axle.

BLUE BAG

STEP

• MODEL E3000 ONLY: Slide the

console mast cover onto the console

mast. With the included wire-tie, pull

the sensor wire and resistance cable

through the console mast. Place the

console mast into the console mast

mounting-bracket and secure with

seven bolts (M8x15L) and six lock

washers (M8). Tighten with the 5MM

Allen wrench. Slide the console mast

cover into place so it integrates with

the frame.

• MODEL E3000 ONLY: Turn the

tension knob to level 15. Direct the

cable on the tension knob through the

tension knob bracket and into the

console mast. Connect the cable to

the tension cable located inside the

console mast. Secure the tension knob

to the tension mast with the screw

(M5x70L) and Phillips screwdriver.

• MODEL E3100 ONLY: Unfold the

console mast and slide the mast into

the console mast mounting-bracket.

Secure the console mast with the

seven bolts (M8x15L) and six lock

washers (M8). Tighten with the 5MM

Allen wrench. Slide the console mast

cover into place so it integrates with

the frame.

• MODEL E3200 & E3200HRT ONLY:

Slide the console mast cover onto the

console mast. Attach the included

wire tie in the console mast to the wire

harness coming from the frame. Pull

this wire trough the console mast while

simultaneously attaching the console

mast to the frame. Secure the console

mast to the frame by tightening the

seven bolts (M8x15L) and six lock

washers (M8) with the 5MM Allen

wrench. Slide the console mast cover

into place so it integrates with the

frame.

• Secure the handlebar onto the

handlebar bracket with two bolts

(M8x20L) and two lock washers

(M8). Tighten with the 5MM Allen

Wrench.

PINK BAG

E3000

Only

STEP

• Remove the four mounting screws

from the back of the console. Connect

the wire harness to the console.

Attach the console to the console mast

using the four mounting screw that

were removed earlier.

• Mount the water bottle bracket to

the console mast with the included

screws.

CONTINUED

621-D East Lake Street • P.O. Box 280 • Lake Mills. WI 53551

toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373

www.visionfitness.com

AG18.11PRD

REV1

STEP

• Slide the seat post cover onto the

seat post.

• Slide the seat post into the frame

and lower the seat post cover into

place.

• Screw the adjustment knob through

the seat post cover and into place on

the frame.

• Attach the seat to the seat post by

tightening the bolts on the underside

of the seat. Use the 14MM Allen

wrench.

GREEN BAG

STEP

• Attach the left and right pedals to the

left and right crank arms. Tighten with

the 15MM Pedal wrench.

BLACK BAG

STEP

Andere Handbücher für E3000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vision Fitness Heimtrainer Handbücher

Vision Fitness

Vision Fitness E3800HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R1400 Bedienungsanleitung

Vision Fitness

Vision Fitness E1500 Frame 9 Bedienungsanleitung

Vision Fitness

Vision Fitness R40 Bedienungsanleitung

Vision Fitness

Vision Fitness R40 Bedienungsanleitung

Vision Fitness

Vision Fitness E3200 Frame 9 Bedienungsanleitung

Vision Fitness

Vision Fitness E3600HRC Bedienungsanleitung

Vision Fitness

Vision Fitness R60 Bedienungsanleitung

Vision Fitness

Vision Fitness Fitness Cycle E3100/3200 Bedienungsanleitung

Vision Fitness

Vision Fitness R2200HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R1400 Bedienungsanleitung

Vision Fitness

Vision Fitness V-SERIES Bedienungsanleitung

Vision Fitness

Vision Fitness SIMPLE Bedienungsanleitung

Vision Fitness

Vision Fitness R2200HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R70 Bedienungsanleitung

Vision Fitness

Vision Fitness E4000 Bedienungsanleitung

Vision Fitness

Vision Fitness R2600HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R2000 Bedienungsanleitung

Vision Fitness

Vision Fitness E3600HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R70 Bedienungsanleitung

Vision Fitness

Vision Fitness E3200 Frame 9 Bedienungsanleitung

Vision Fitness

Vision Fitness R2600HRC Bedienungsanleitung

Vision Fitness

Vision Fitness R2250HRT Bedienungsanleitung

Vision Fitness

Vision Fitness ES600 Bedienungsanleitung

Beliebte Heimtrainer Handbücher anderer Marken

TOORX

TOORX BRX85 Bedienungsanleitung

Matrix

Matrix KranKcycle Bedienungsanleitung

Weslo

Weslo Vector 302 Kurzanleitung

Matrix

Matrix IC3 Bedienungsanleitung

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Bedienungsanleitung

Monark

Monark 827E Bedienungsanleitung

Stamina

Stamina 1310 Bedienungsanleitung

American Fitness

American Fitness SPR-BK1072A Bedienungsanleitung

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Bedienungsanleitung

BH FITNESS

BH FITNESS H9158H Bedienerhandbuch

Body Sculpture

Body Sculpture BC-7220G Bedienungsanleitung

Cateye

Cateye EC-2300 Bedienungsanleitung

FYTTER

FYTTER RACER RC MSR Bedienungsanleitung

Kikos

Kikos HM-9090M Bedienungsanleitung

Fuel Fitness

Fuel Fitness SU135-40 Bedienungsanleitung

NordicTrack

NordicTrack Gxr 4.2 Bike Bedienungsanleitung

Stamina

Stamina 15-0340A Bedienungsanleitung

KIDSFIT

KIDSFIT Cardio Kids 661 Bedienungsanleitung