Vision Fitness E4100 Bedienungsanleitung

ASSEMBLY INSTRUCTIONS

E4100

To avoid possible damage to this Fitness Cycle,

please follow these assembly instructions.

Carefully remove all its parts from the box,

lay them out and review the parts list.

If any parts are missing, please call 1-800-335-4348, Ext 12

Before proceeding, find your Fitness Cycle’s serial number,

located on the underside of main frame, and enter here:

______________________________

Refer to this number when calling for service.

IT ALL STARTS WITH A VISION

A41.2

E4100 Parts Diagram

VISION FITNESS E4100 Parts Description

Part # Description Count Dimensions

Front Wheel Parts

#60 Front Foot Wheel Axle 1

#61 Front Transport Wheels 2

#182 Outside Wheel Washers 2

#183 Wheel Attachment Nuts 2

Arm Assembly Parts

#116 Right Arm 1

#115 Left Arm 1

#74 Plastic Arm Cam Cover 2

#105 Inside Cam Pulley 2

#106 Outside Cam Pulley 2

#169 Pulley Washer 4 Flat

#107 Cam Pulley Spring 2

#183 Cam Pulley Locknuts 2

Frame Parts

#62 Rear Foot Assembly 1

#167 Rear Foot Attach Bolts 4 20mm L x 8mm D

#65 Seat Post 1

#108 Seat 1

#82 Top Cap 1

#176 Top Cap Screws 3

Console Assembly Parts

#70 Console Mast 1

#78 Console Mast Plug 1

#168 Console Mast Bolts 2 38mm L x 8mm D

#95 Console 1

#96 RPM Sensor Wire 1

#179 Upper Magnet Shift Cable 1

#143 Lower Magnet Shift Cable 1

#163 Console Attachment Bolts 6 11mm L x 5mm D

Other Parts

#91 Pedals 2

E4100 Parts

E4100 Assembly

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in

before completely tightening any ONE bolt.

Step 1 • Rear Foot

1:Secure the Rear Foot Assembly (62) to the Frame by using the four Rear Foot Attachment Bolts (167).

Step 2 • Seat and Seat Post

1: Slide the Seat Post (65) into the frame seat post receiver tube. The seat post numbers should be

facing the right or seat pin side of the Fitness Cycle.

NOTE: Both nuts in the Seat Clamp should be tightened at the same time, to ensure a proper fit.

2: Attach the Seat (108) to the Seat Post (65) and tighten securely. To avoid scratching the seat post

paint, always hold the the seat pin knob out when adjusting the seat post height.

Step 3 • Console Mast

1: Remove the Top Cap Screws (176) which hold the Top Cap (82) to the frame. Then remove the Top

Cap (82).

NOTE: DO NOT thread in the Water Bottle Cage Bolts yet. Never slide the Top Cap (82) on or off with

the Waterbottle Cage Bolts threaded in, as they will scratch the paint on the Console Mast (70).

2: Slide the Top Cap (82) over the bottom of the Console Mast (70). The VISION decal on the Console

Mast (70) should be facing forward, away from the rider.

3: Locate the RPM Sensor Wire (96) and the Lower Magnet Shift Cable (143). Holding the Top Cap (82)

and Console Mast (70) above the frame console mast receiver tube, guide the RPM Sensor Wire (96)

and the Lower magnet Cable (143) through the Console Mast (70) while simultaneously sliding

the Console Mast (70) into the receiver tube.

4: Lift the Top Cap (82) up, install the two 38mm-long Console Mast Allen bolts (168) and tighten

securely.

5: Now slide the Top Cap (82) back into place. Make sure that the back end of the Top Cap (82) is

nested fully into the Seat Cap groove. Secure the Top Cap (82) by threading the three Top Cap Screws

back into their holes.

NOTE: Check that there are no large gaps between the Top Cap (82) and the Side Covers.

Step 4 • Console

1: Feed the Upper Magnet Shift Cable (179) into the topmost opening of the Console Mast (70).

2: Plug the RPM Sensor Wire (96) into the Console (95). DO NOT PINCH the RPM Sensor Wire (96)

between the Console (95) and the Console Mast (70). Make sure the cable fits in the slot cut in the

Console Mast Mount.

3: Mount the Console (95) to the Console Mast (70) using the six Console Attachment Phillip Head Bolts

(163).

E4100 Assembly

Step 5 • Connect Magnet Shift Cable

1: Turn the Tension Knob to position 8. Reach inside the opening

of the Console Mast (70) and connect the Upper Magnet Shift

Cable (179) to the rectangular red cable-slide on the end of the

Lower Magnet Shift Cable (143), as shown in the accompanying

illustrations.

2:While holding the metal separating tab (Figure 5), turn the

Tension Knob to Level 1 and then pull the tab out and discard.

3:Press the Console Mast Plug (78) into the opening of

the Console Mast (70).

Step 6 • Install Arms and Front Wheels

1: Tip the Fitness Cycle back until it is balanced on the Seat and

the back of the Rear Foot Support. Place cardboard beneath

the seat to avoid tearing or marring the seat cover.

2: Identify the Left and Right Arms (115 & 116). Insert the Front

Foot Wheel Axle (60) through the frame axle hole.

3: Remove the Cam Pulley Locknut (183), the two Pulley Spring

Washers (107), and the Outside Cam Pulley (106) from the Cam

Pulley Arm (75). Note the order and direction of these parts

before removal.

4: Place the bottom hole of the Right Arm (116) onto the Front

Foot Wheel Axle (60). Position the Right Arm (116) so that the

chromed slot rests against the inside Cam Pulley (105).

5: Place a thin layer of grease on the pulley surfaces. Reassemble

the parts removed in the above steps onto the Cam Pulley Arm

(75). Do not yet tighten the Cam Pulley Locknut (183).

E4100 Assembly

6: Slip the Front Transport Wheel (61) onto the right side of the Front

Foot Wheel Axle (60). Secure this wheel with the Outside Wheel

Washer (182) and the Wheel Attach Nut (183). This nut should be

tightened until the wheel has no side-to-side play, but it can still

be easily rotated with your fingers.

7:Tighten the Cam Pulley Locknut (183). NOTE: This nut must be

tightened all the way down or the Pulleys may loosen. When the

Locknut is properly adjusted, the Outside Cam Pulley (106) can

be turned with your fingers, and there will be no side-to-side play

in the arm.

NOTE: Production models prior to 3/97 had TWO Cam Pulley

locknuts instead of the newer SINGLE Cam Pulley Locknut (183).

8:Repeat the above procedure with the Left Arm (115).

9:Tighten the Axle Bushing Allen Bolts (157). Snap the Plastic Arm

Cam Covers (74) into place on each arm. Check that they are

secure and even.

NOTE

Symptom: Too much resistance.

Cause: The black Cam Follower Pulleys OR the Wheel Axle Nuts

have been overtightened. When the nylock Cam Pulley Locknut

(183) has been tightened, the cam pulley should be able to be

turned with your fingers. If it cannot be turned, the nylock nut is

too tight. Also check that the wheel axle nuts are not too tight.

The wheels should also be able to be turned with your fingers. If

not, the axle nut is too tight.

E4100 Final Assembly

Step 7 • Pedals

1: Identify the left and right Pedals (91). Grease the Pedal threads,

thread each Pedal into the correct left and right crank arms and

tighten.

NOTE: It is very important to FULLY TIGHTEN each pedal using a

long wrench. Failure to do so will result in loosening and NOISE.

Step 8 • Install Batteries and Test Operation

1:Remove the battery compartment lid on the back of the Console

(95) and install the Batteries. Two AA-cell batteries are required.

2:The Console provides accurate workload readouts because it

knows which position the magnet is in through a sensor located

at the base of the tension knob. To check the operation of this

sensor, immediately after battery installation the ‘ML’ icon will be

flashing and a number from 1 to 8 will show in the WORKLOAD

window. This number should indicate the position of the tension

knob.Turn the tension knob from 1 through 8 and check that the

number in the WORKLOAD window matches the number on the

tension knob. Once any key is pressed, the ‘ML’ icon will stop

flashing and WORKLOAD window will display only watts.

3:To change the display to Kilometers, consult the Owner’s Manual.

4:Test ride the bike and make sure that all console feedback

functions are operational.

CAM ARM

SILVER

WASHER

SILVER

WASHER

SILVER

WASHER

SILVER

WASHER BLACK

WASHER

BLACK

WASHER

NUT

NUT INSIDE CAM

PULLEY WHEEL

INSIDE CAM

PULLEY WHEEL

OUTSIDE CAM

PULLEY WHEEL

OUTSIDE CAM

PULLEY WHEEL

SPRING

COMPLETE SIDE VIEW

E4100 CAM PULLEY WHEEL W/SPRING INSTRUCTIONS

(SERIAL #1198-CURRENT)

621-D East Lake Street

P.O. Box 280

Lake Mills, WI 53551

(920) 648-4090

Inhaltsverzeichnis

Andere Vision Fitness Heimtrainer Handbücher

Vision Fitness

Vision Fitness E3000 Bedienungsanleitung

Vision Fitness

Vision Fitness E3000 Bedienungsanleitung

Vision Fitness

Vision Fitness E3200 Frame 9 Bedienungsanleitung

Vision Fitness

Vision Fitness U60 Bedienungsanleitung

Vision Fitness

Vision Fitness R40 Bedienungsanleitung

Vision Fitness

Vision Fitness R2000 Bedienungsanleitung

Vision Fitness

Vision Fitness R1500 Frame 9 Bedienungsanleitung

Vision Fitness

Vision Fitness SIMPLE Bedienungsanleitung

Vision Fitness

Vision Fitness R2050 Bedienungsanleitung

Vision Fitness

Vision Fitness R2600iNetTV Bedienungsanleitung

Vision Fitness

Vision Fitness E1500 Frame 9 Bedienungsanleitung

Vision Fitness

Vision Fitness E3000 Bedienungsanleitung

Vision Fitness

Vision Fitness R1400 Bedienungsanleitung

Vision Fitness

Vision Fitness R2600HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R2200HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R2200 Bedienungsanleitung

Vision Fitness

Vision Fitness Fitness Cycle E3100 Bedienungsanleitung

Vision Fitness

Vision Fitness E3800HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R2100 Bedienungsanleitung

Vision Fitness

Vision Fitness E3600HRT Bedienungsanleitung

Vision Fitness

Vision Fitness U70 Bedienungsanleitung

Vision Fitness

Vision Fitness E4000 Bedienungsanleitung

Vision Fitness

Vision Fitness R20 Bedienungsanleitung

Vision Fitness

Vision Fitness U60 Bedienungsanleitung

Beliebte Heimtrainer Handbücher anderer Marken

TOORX

TOORX BRX85 Bedienungsanleitung

Matrix

Matrix KranKcycle Bedienungsanleitung

Weslo

Weslo Vector 302 Kurzanleitung

Matrix

Matrix IC3 Bedienungsanleitung

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Bedienungsanleitung

Monark

Monark 827E Bedienungsanleitung

Stamina

Stamina 1310 Bedienungsanleitung

American Fitness

American Fitness SPR-BK1072A Bedienungsanleitung

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Bedienungsanleitung

BH FITNESS

BH FITNESS H9158H Bedienerhandbuch

Body Sculpture

Body Sculpture BC-7220G Bedienungsanleitung

Cateye

Cateye EC-2300 Bedienungsanleitung

FYTTER

FYTTER RACER RC MSR Bedienungsanleitung

Kikos

Kikos HM-9090M Bedienungsanleitung

Fuel Fitness

Fuel Fitness SU135-40 Bedienungsanleitung

NordicTrack

NordicTrack Gxr 4.2 Bike Bedienungsanleitung

Stamina

Stamina 15-0340A Bedienungsanleitung

KIDSFIT

KIDSFIT Cardio Kids 661 Bedienungsanleitung