VMP LCD-DM2 Bedienungsanleitung
VIDEO MOUNT PRODUCTS
Instruction Sheet For:
LCD-DM2
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: 410.643.6390 Fax: 410.643.6615
www.videomount.com
-----
--
12
ND
PLUG
LCD-DM2
"U"
CONNECTOR
I 2
2A
~
I 1
CONNECTOR
A
2B
CONNECTOR
B
3 1
OUTER
TUBE
2
4
WASHER
010.2*¢J80*T2.0
5
IMETAL
WASHER
¢Jl0.5*¢J86*T3.0
2
LLEN
SCREW
MfO*Pl.5*L50
LLEN
KEY
M6
toSS
SCREW
M6*Pf.O*Lf2
4
10
SCREW
M5*Pf.0*L8
4
4
~
l)
®---]
\;l
Il)
l'i
VIDEO
MOUNT
PRODucr5
Step1
Before starting, lay out all parts to your mount and match them to the
parts list provided. Verify that you have all your parts before attempt-
ing to assemble the mount. Note: The LCD-DM2 and LCD-1 combo was
designed to mount two of the same TV or TVs of similar size and weight.
It is not designed to have two signif cantly different TVs mounted. Also
note that LCD-1 part numbers have hexagons around their numbers
and LCD-DM2 has circles around its part numbers.
Through bolting the LCD-DM2
Step 2
Mark the desk or desired mounting surface in preparation of instal-
lation of the bottom tube LCD-DM2. Drill a ½” hole through the
desired mounting surface. Place a plastic washer LCD-DM2 on
either side of the drilled hole and place metal washers LCD-DM2
on top of the plastic washers LCD-DM2. Insert the M10 screw
LCD-DM2 through the bottom most metal washer LCD-DM2
through to the top most metal washer and then screw the bottom
tube LCD-DM2 onto the M10 screw. Warning: Please verify
that your mounting surface will support the combined weight of
your mount, mounting hardware, and monitor. Also verify that the
mounting surface is safe to drill through. If in doubt, please contact
a professional installer.
Step 3
Make sure the flat head screw LCD-DM2 is connecting the bottom
tube LCD-DM2 to the base seat LCD-DM2. Note: The mount
may come assembled with the button cap M10 screw LCD-DM2
attaching the base seat please make sure to attach the flat head
screw instead.
Step 4
Place the clamp on the edge of the desk or mounting surface and
turn the adjustable bolt LCD-DM2 until the fixed plate LCD-
DM2 is tight against the bottom of the desk or desired mounting
surface. Warning: Please verify that your mounting surface will sup-
port the combined weight of your mount, mounting hardware, and
monitor. If in doubt, please contact a professional installer.
Step 2: Through bolting the mount
Step 3: Connecting the base seat
Step 4: Clamping down on the desk
VIDEO MOUNT PRODUCTS
Key:
LCD-1
LCD-DM2
3
17
4
5
4
6 5
3
321
6
19 18
Step 5
Now is time to adjust height of the upper tube LCD-DM2 and
connectors A and B and LCD-DM2 to the desired height of
your TV. To adjust the height of the upper tube LCD-DM2 simply
remove the M8 screw LCD-DM2 and nylon nut LCD-DM2.
Next slide the upper tube LCD-DM2 along the bottom tube
LCD-DM2 matching up the height adjustment holes on the
two of them until you get your desired height. Then secure the up-
per tube LCD-DM2 again using the M8 screw LCD-DM2
and nylon nut LCD-DM2. To adjust the connectors and
LCD-DM2 loosen the M6 screws LCD-DM2 and slide the
connectors to the desired height along the upper tube LCD-
DM2. Retighten the screws LCD-DM2 once the connectors
and LCD-DM2 are in the proper position.
Step 6
For this step it is assumed that you have assembled the LCD-1 to
the configuration desired, but have not attached the monitors to
the mounting plates. If this is not the case, please take the time to
assemble the LCD-1. Insert the plastic flanges LCD-1 into the
desired arm or LCD-1. Now use the 3/8” bolt LCD-1
and nylon nut LCD-1 to connect the arm or LCD-1
to the “U” connector LCD-DM2.
Step 7
Attach the monitors to the mounting plate or LCD-1 using
M4 LCD-1 or M5 LCD-1 screws. Please verify that all nuts
and screws are tight.
Step 5: Adjusting height
Step 6: Attaching LCD-1s
Step 7 : Attaching monitors
3
13
1
19 20
WARNING: The installer of these products must verify that the mount-
ing surface, ceiling or wall, will safely support the combined weight
of all attached equipment and hardware. Video Mount roducts will
not be held liable for the improper use or installation of its products.
Enjoy Your Mount!
2A 2B
2B
2A
15
1413
13
1514
13
9
2A
913
2B
5A 5B
11
17
18
8
2
8
2
Inhaltsverzeichnis
Andere VMP Rack & Stand Handbücher
VMP
VMP FRM Series Bedienungsanleitung
VMP
VMP FP-XMF Bedienungsanleitung
VMP
VMP ER-1-4PKIT Bedienungsanleitung
VMP
VMP PMC-S Bedienungsanleitung
VMP
VMP LCD-FT Bedienungsanleitung
VMP
VMP VH-004 Bedienungsanleitung
VMP
VMP LCD-2 Bedienungsanleitung
VMP
VMP PMC-L Bedienungsanleitung
VMP
VMP LCD-CM2B Bedienungsanleitung
VMP
VMP LCD-MID-FT Bedienungsanleitung
VMP
VMP PDS-LFT Bedienungsanleitung
VMP
VMP AP-2B Bedienungsanleitung
VMP
VMP PDS-LCM2B Bedienungsanleitung
VMP
VMP FP-LDSB Bedienungsanleitung
VMP
VMP DVR-WA Bedienungsanleitung
VMP
VMP LCD-2537C Bedienungsanleitung
VMP
VMP FP-MFTB Bedienungsanleitung
VMP
VMP VH-001 Bedienungsanleitung
VMP
VMP ER-148-4PKIT Bedienungsanleitung
VMP
VMP PM-LP Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
