VMP LCD-PV Bedienungsanleitung
LCD-PV
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: 410.643.6390 Fax: 410.643.6615
www.videomount.com
43
44 1
19
2
17
3321
22
16 15
6
9
4
5
3
7
8
12
11
10
30
28
29
31
27
26
13
25
24
32
23
42
20
14
41
38
36
35
37
34
18
36
39
40
LCD-PV
45
46
ITEM
NO.
DESCRIPTION
QTY.
1
Ceiling Plate
1
2
Extension Tube
1
3
Support Tube
1
4
Swivel Bracket
1
5
Small Mounting Plate
1
6
Large Mounting Plate
1
7
Nylon Nut M6*P1.0
1
8
Nylon Nut 3/8" - 16UNC
1
9
Screw M6*P1.0*L40
1
10
Screw 3/4"-16UNF*L74
1
11
Washer
3/4"*
46 2
12
Adjustable Screw 3/8"-
16UNC*L68mm
1
13
Cable Clip
2
14
End Plug
1
15
Washer
3/8"*
19*T1.6
2
16
Screw 3/8" - 16UNC*L2"
1
17
Brake Screw 1/4" - 20UNC*L1/2"
1
18
Screw 5/16" - 18UNC*L1.75"
1
19
Nylon Nut 5/16" - 18UNC
1
20
M3 Allen Key
1
21
Screw M5*P0.8*L12
4
22
Screw M4*P0.7*L12
4
23
Thin Nut M8*P1.25
1
24
L Connector
1
25
Connector (L=85)
1
26
Connector (L=45)
1
27
Round Metal
1
28
Screw 1/4" - 20UNC
1
29
Swivel Metal
1
30
Nut 1/4" - 20UNC
1
31
Brake Screw M6*P1.0*L6
2
32
Connector (L=150)
1
33
Screw M6*P1.0*L12
4
34
Hex Nut 5/8" - 11UNC
1
35
Lock Washer 5/8"
1
36
Brake Screw 1/4" - 20UNC*L3/8"
3
37
Female Pipe Couple
1
38
End Plug
1
39
Metal Washer
1
40
Gap Washer
44.5*
17.5*T2.5
1
41
Screw 5/8" - 11UNC*L4"
1
42
Ceiling Plate
1
43
Lag Screw 5/16"*L2.5"
4
44
Washer
8.3*
19*T1.6
4
45
Screw M8*P1.25*L16
4
46
Washer
4.3*
12*T1.0
4
Step 1
Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount.
Step 2
Determine the VESA standard that your TV follows to determine
which VESA plate you will be using. For VESA 75 or 100 use the
small mounting plate and for VESA 200 or 100x200 use the large
mounting plate . Once you have determined the correct VESA
plate for your TV, attach the plate or #6) to the pivot bracket
(#4) using an M6 screw (#9) and nylon nut (#7).
Step 3
Attach the swivel bracket (#4) to the support tube (#3) using the
3/8” screw (#16), washers (#15) and nylon nut (#8). Insert the ad-
justing screw (#12) into the back of the pivot bracket (#4) for use
when tilting the monitor.
If you plan to use the ceiling mast:
Step 4
Mark the ceiling or desired mounting surface in preparation of in-
stallation of ceiling plate (#1). If mounting to wooden ceiling joists,
pre drill pilot holes using a 7/32” drill bit. Attach the ceiling plate
(#1) to the wooden ceiling joist using the 5/16” by 2.5” long lag
screw (#43) and washer (#44). WARNING: Please verify that your
mounting surface will support the combined weight of your mount,
mounting hardware, and flat panel. Also verify that the mounting
surface is safe to drill through. Please note only mounting hardware
for mounting to wooden ceiling joists will be provided with the unit.
If mounting to a surface other than wooden ceiling joists then other
hardware will be required. If in doubt or uncertain about any of the
above, please contact a professional installer.
Step 5
Attach the extension tube (#2) to the
support tube (#3) using the ¾” bolt
(#10) and washers (#11). Then screw
the longer ¼” brake screw (#17) into
the extension tube (#2) so that it is
tight against the ¾” bolt (#10). This will
prevent the ¾” bolt (#10) from turning
loose within the extension tube (#2).
Step 2 : Selecting the correct
mounting plate
Step 3: Attaching the pivot bracket
Step 5(Right) : Attaching the
extension tube
Step 4: Mounting the ceiling plate
2
15
6
5
3
16
6
5
47
9
3
4
12
8
4
1
1
44
43
10 11
17
2
10
10
2
Step 6
Attach the mounting plate assembly from step 2 to your flat pan-
el using the M4 (#21), M5 (#22), M6 (#33) or M8 (#45) screws as
appropriate. NOTE: If you are using M4 screws with the Large
Mounting Plate (#6) then you have to use the small washers (#46)
provided with the M4 screws (#21).
Step 7
Connect the extension tube (#2) to the ceiling plate (#1) using
the 5/16” screw (#18) and nylon nut (#19). Proceed to step 12
If you plan to use 1.5” NPT as a ceiling mast:
Step 8
Mark the ceiling or desired mounting surface in preparation of
installation of ceiling plate (#42). If mounting to wooden ceiling
joists, pre drill pilot holes using a 7/32” drill bit. Attach the ceiling
plate (#42) to the wooden ceiling joist using the 5/16” by 2.5” long
lag screw (#43) and washer (#44). WARNING: Please verify that
your mounting surface will support the combined weight of your
mount, mounting hardware, and flat panel. Also verify that the
mounting surface is safe to drill through. Please note only mount-
ing hardware for mounting to wooden ceiling joists will be pro-
vided with the unit. If mounting to a surface other than wooden
ceiling joists then other hardware will be required. If in doubt or
uncertain about any of the above, please contact a professional
installer.
Step 9
Attach the female pipe couple (#37, #38 & #36) to the top of the
support tube (#3) using the 5/8” screw (#41), washers (#39 & #40),
spring washer (#35) and hex nut (#34).
Step 6: Attaching the monitor
(monitor not included)
42
43
42
44
Step 7: Connecting the ceiling
plate and the extension tube
Step 8: Mounting the ceiling plate Step 9: Attaching the female
pipe couple
12
19
18
37 36
38
341 40
39
35 34
6
21 22 33
46
21
45
Step 10
Attach the mounting plate assembly from step 2 to your flat panel
using the M4 (#21), M5 (#22), M6 (#33) or M8 (#45) screws as appro-
priate. NOTE: If you are using M4 screws with the Large Mounting
Plate (#6) then you have to use the small washers (#46) provided
with the M4 screws (#21).
Step 11
Screw in the 1.5” NPT pipe into the top of the female pipe couple
(#37) and the ceiling plate (#42). Screw ¼” brake screws (#36) into
the top of the female pipe couple (#37) and ceiling plate (#42) so
the brake screws are tight against the pipe. This will help prevent the
pipe from turning out of the pipe couples.
Step 12
If you desire to use the camera bracket then follow this step, other-
wise proceed to the next step. First determine if you wish the camera
to be mounted below or to the side of the monitor. Then determine
how long the camera arm needs to be to extend past the side or
bottom of the monitor. Use the connectors provided (#25, #26 &
#32) to extend the L connector (#24) as needed. Take the end as-
sembly (#27, #28, #29, #30 & #31) and screw it to the connector
(#24, #25, #26 or #32) furthest from the center of the mount. Make
sure the M6 brake screws (#31) are tight in the swivel metal (#29).
Step 13
Attach your monitor to the chosen mounting plate (#5 or #6) using
the M4 (#21), M5 (#22) or M6 (#33) screws as appropriate.
Please verify that all nuts and screws are securely tightened.
Step 11 : Inserting the 1.5” NPT
(monitor not shown for clarity)
Step 12: Using the camera
bracket
WARNING: The installer of these products must verify that the mount
surface, ceiling or wall, will safely support the combined weight of
all attached equipment and hardware. Video Mount Products will
not be held liable for the improper use or installation of its products.
Enjoy Your Mount!
37
33
56
42
21 22
36
37 42
25 26
32 24
27 28 29 30 31
31 29
25 26 32
24
6
21 22 33
Step 10: Attaching the monitor
(monitor not included)
46
21
45
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere VMP Rack & Stand Handbücher
VMP
VMP VH-001 Bedienungsanleitung
VMP
VMP ER-184-4PKIT Bedienungsanleitung
VMP
VMP ER-W24 Bedienungsanleitung
VMP
VMP PMC-L Bedienungsanleitung
VMP
VMP LCD-DM2 Bedienungsanleitung
VMP
VMP ER-1-4PKIT Bedienungsanleitung
VMP
VMP FP-SFT Bedienungsanleitung
VMP
VMP FP-LFV Bedienungsanleitung
VMP
VMP LCD-1C Bedienungsanleitung
VMP
VMP LCD-1C Bedienungsanleitung
VMP
VMP PDS-LC Bedienungsanleitung
VMP
VMP VH-004 Bedienungsanleitung
VMP
VMP ER-1 Bedienungsanleitung
VMP
VMP DVR-WA Bedienungsanleitung
VMP
VMP ER-148-4PKIT Bedienungsanleitung
VMP
VMP FP-MFTB Bedienungsanleitung
VMP
VMP W-20B Bedienungsanleitung
VMP
VMP FP-SFB Bedienungsanleitung
VMP
VMP AP-1 Bedienungsanleitung
VMP
VMP FP-XMF Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
