Wali M002-W Bedienungsanleitung

M002-W

WARNING

！

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.

SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may

cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.

Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect

assembly or inappropriate use.

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

Dual Monitor Desk Mount

75x75\100x100

VESA Plate

e (x2)

Swivel Arm

d (x1)

C-Clamp

b (x1)

C-Clamp Brace

c (x1)

Pole

a (x1)

Wire Clip

n2 (x4)

Wire Clip

n1 (x1)

Grommet Base Plate

m (x1)

M4 Spacer

s (x8)

M8x12 Bolt

g (x2)

Nut

h (x2)

M5x14 Bolt

f (x3)

Wrench

p (x1)

Allen Key

o (x1)

M4x30 Bolt

r (x8)

M4x12 Bolt

q (x8)

M10 Bolt

i (x1)

Support Plate

j (x1)

M10 Washer

k (x1)

Spring Washer

l (x1)

Measure the thickness of your mounting surface or desk.

INSTALLATION MANUAL

1-844-SATTLER (18447288537)

[email protected]

www.walielectric.com

(10kg/22lbs)x2

RATED

MAX 27”

TIPOVER WARNING

RT OF MONITOR OR STAND.

Supplied Parts List

Option A : Clamp Installation

1. Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and

tighten with Allen Key 3mm o .

Option A : Clamp Installation

2Option B : Grommet Base Installation

I. Place Pole a onto Grommet Base Plate m . Connect them from the bottom using M5x14 Bolt

and tighten with Allen Key 3mm .

2. Select the preferred height according to your desk thickness. Connect C-Clamp b to C-Clamp

Brace c using M8x12 Bolt g and tighten with Allen Key 5mm o . Rotate the hand knob

clockwise to fasten for stability.

Fit clamp: 0.4”- 4”

Grommet: 0.4”- 3”

Hand Knob

a c f

3Put the Wire Clip n1 and Swivel Arm d through the Pole a , adjust the preferred height and

tighten using Allen Key 6mm o . Attach the Wire Clips n1 to the Swivel Arm d .

6If one monitor is lower, remove the Nut h and turn the bolt counter-clockwise using

Allen key 3mm o to raise the monitor. Tighten the VESA Plate e with Nut h for stability

after the adjustment.

5Put the assembled TV/Monitor onto the Swivel Arm d and tighten the VESA Plate e with

Nut h for stability.

Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included)

8Manually swivel, tilt, and rotate the monitor for the best viewing angle.

7Guide the cable through the Wire Clips ( n1, n2 ) and store the Allen Keys o in the Wire Clip n1 .

Adjust the tilt angle using Allen Key 5mm n .

n1 n1

aja

n1n2

Step 4.1

Select Monitor Screws

2a. Existing Grommet Hole Installation

If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before

installing the desk mount. Position the Pole a on the mounting surface and secure using the

Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the Bolt using

the provided Wrench p .

2b. Self-drilled Grommet Hole Installation

Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm) diameter hole at the

marked position through the mounting surface. Position the Pole a on the mounting surface and

secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the

Bolt using the provided Wrench p .

90°

Step 4.3a

Flat Back Monitor

Step 4.3b

Curved or Recessed Back Monitor

M4x12 M4x30

jkli

jkl

Ignore this step if monitors are level.

ø 10mm

(ø ")3/8

Only one screw size fits your Monitor

Step 4.2

Select Spacers ( if needed )

Hand thread screws into the

threaded inserts on the back

of your Monitor to determine

which screw (M4x12 or M4x30)

to use.

Notice: Please make sure the security nut h is installed before you rotate the monitor.

Andere Wali Rack & Stand Handbücher

Wali

Wali TVDVD-04 Bedienungsanleitung

Wali

Wali SWM-EH-01B Bedienungsanleitung

Wali

Wali SBR201 Bedienungsanleitung

Wali

Wali TVDVD-01 Bedienungsanleitung

Wali

Wali GPV002 Bedienungsanleitung

Wali

Wali GSMP001 Bedienungsanleitung

Wali

Wali TVF001 Bedienungsanleitung

Wali

Wali 1342LM Bedienungsanleitung

Wali

Wali WMH002-B Bedienungsanleitung

Wali

Wali PRS001 Bedienungsanleitung

Wali

Wali GSDM003 Bedienungsanleitung

Wali

Wali M001LP Bedienungsanleitung

Wali

Wali MF002XLS Bedienungsanleitung

Wali

Wali M12XXL Bedienungsanleitung

Wali

Wali CS203 Bedienungsanleitung

Wali

Wali M001-W Bedienungsanleitung

Wali

Wali CS202 Bedienungsanleitung

Wali

Wali CS201 Bedienungsanleitung

Wali

Wali M001SXL Bedienungsanleitung

Wali

Wali GSWM002 Bedienungsanleitung

Wali

Wali GSMP002 Bedienungsanleitung

Wali

Wali GSM002XL Bedienungsanleitung

Wali

Wali 2655LO Bedienungsanleitung

Wali

Wali 1742LM Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung