WE-EF ETC320-GB LED Bedienungsanleitung

WE-EF LEUCHTEN

Installation and Maintenance

Instructions

Inground Luminaire

ETC320-GB LED

Surge Protection

This product features built-in surge protection circuitry in compliance

with applicable standards.

For comprehensive protection of a luminaire installation against lightning

and electrical surges, it is essential to cover mains supply and data input

lines at the distribution board level, by using respective primary (Type 1)

and secondary (Type 2) surge arrestors in compliance with EN61643-11/

IEC61643-1.

Warning

Ensure that all required surge protection measures are in place and

activated prior to luminaire installation. Also, disconnect luminaires

before operating high-power devices such as, for example, electrical

arc welders.

IP69, Class I, ta = 25°C

;

Fig. I

Inground Luminaire

355º

ø 160

ø 350

180

0º-20º

Light Source

LED

Maintenance

Warning: Do not open luminaire while mains supply is switched on.

 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\

2) Remove cover and lens/gasket assembly. Clean all surfaces and ensure that threaded entries are free

from dirt by using a wet cloth with mild detergent.

3) Check gasket for damage and replace if necessary.

Attention: In case of damage to the lens, the complete lens/gasket assembly must be replaced.

4) In case of damage to the LED, the complete gimbal module Xmust be returned to WE-EF for factory-

maintenance (contact your authorised WE-EF agent for service). To remove the gimbal module proceed

as follows (Fig. I):

a) Rotate wheel W(using a standard tool) in the direction of the 'open' mark until the gimbal module can

be pulled out of the luminaire housing.

b) Detach terminal connector Yand remove gimbal module X.

c) Properly package gimbal module Xand return to WE-EF for factory-maintenance.

Attention: During the factory-maintenance period, ensure both the luminaire cover and lens are secured

in position.

5) To install gimbal module X, attach terminal connector Y. Set gimbal module Xinto luminaire housing.

Rotate wheel Win the direction of the 'lock' mark until gimbal module XLVĥUPO\VHFXUH)ROORZVWHSV

11-16 to close the luminaire (see: Phase Two – Luminaire Installation, Electrical Connection, and Aiming

Procedure).

Damaged mains supply cable: Contact your authorised WE-EF agent for replacement.

Installation

The product must be installed and maintained

E\DVXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFH

with latest building/construction and/or electrical

regulations and relevant legislation.

Warning:6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWR

installing and connecting the luminaire.

Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHU

than the original manufacturer, then the warranty will

no longer be valid and shall become the full

responsibility of the modifying person/organisation.

Claims based on defects attributable to improper

installation and/or application, and the consequences

thereof, are excluded.

Installation Methods

For proper installation, use the supplied installation

blockout.

Ensure that proper drainage is provided for

the shown installation methods:

In landscape/paved areas, sand or concrete with

gravel base (Fig. I).

With fully concreted installation, drainage piping

must be provided (Fig. II).

Fig. III

Fig. II

Phase One

Blockout Installation Procedure

(during earth or masonry work)

1) Ensure that proper drainage is provided for the

shown installation methods.

Ensure a suitable recess is provided to accommodate

installation blockout/mounting ring assembly L/H.

3) Test drainage (ensure water drains within 30 mins,

Warning: warranty void if luminaire installed

without appropriate drainage).

4) Set installation blockout/mounting ring assembly

L/H in position and ensure that:

a) Arrow Ron mounting ring His pointed towards

the object to be illuminated (wall, tree, column).

b) Mounting ring HLVĦXVKZLWKVXUIDFHF.

,IWKHĦRRUZLOOEHWLOHGRUSDYHGDIWHUZDUGVOHDYH

an appropriate gap.

c) Mains supply cable(s) OLVRIVXĩFLHQWOHQJWK

to connect sealable junction box Jwith cable N

from luminaire.

5) During ongoing earth and/or masonry works,

do not remove screws M from mounting ring H.

Ensure that installation blockout/mounting ring

assembly L/H is not damaged and has maintained

its original shape. If necessary use a cover plate.

6) Framing should be installed to prevent vegetation

from growing over the lens.

Aiming of gimbal

14)Insert a standard tool into a slot on locking wheel

W. Rotate locking wheel Win the ‘OPEN’ direction

until gimbal can be moved (Fig. V).

To horizontally aim the gimbal

(Rotation 355°)

+ROGĥQVEto rotate the gimbal.

To vertically aim the gimbal

(Tilt 0-20°)

a) Insert screw driver into hole T.

b) Adjust gimbal to desired angle

(Refer to protractor scale U).

Note: Angle can be adjusted in 2° increments.

15)Insert screw driver into a slot on locking wheel W.

Rotate locking wheel Win the ‘LOCK’ direction

XQWLOWKHJLPEDOLVĥUPO\VHFXUHG)LJ9

Warning: Do not tighten more than necessary to

secure gimbal.

16)Ensure that all surfaces are clean and dry.

Reposition lens/gasket assembly B, cover Aand

screws Don luminaire housing C.

Note: Ensure that orientation pin Pis align with

hole Qin gasket (Fig. VI).

17)Switch on mains electrical supply and operate

light source for approximately 30 minutes to dry

any moisture.

Attention: 'RQRWVZLWFKRĪ/('EHIRUHOXPLQDLUH

is properly sealed.

18)Secure cover Aas follow:

a) Partially secure screws Din criss-cross

sequence (Fig. VII) starting from position 1.

b) Tighten screws Din same sequence.

c) Fully tighten screws Din same sequence again,

using torque 3 Nm.

Phase Two

Luminaire Installation, Electrical Connection, and

Aiming Procedure

 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\

8) Check that rating shown on luminaire label

conforms with mains electrical supply.

9) Remove screws Mfrom mounting ring H.

10)Terminate cable N and mains supply cable O

in sealable junction box J and connect leads to

respective terminals:

a) ON/OFF or wireless (L = Phase, N = Neutral,

= Earthing)

b) 1-10 V/DALI (L = Phase, N = Neutral,

= Earthing, DA/DA = DALI control line,

D–/D+ = 1-10 V control line).

Please refer to instruction inside SJB packaging.

11)Remove cover Aand lens/gasket assembly Bby

loosening screws D.

12)Set cables and sealable junction box Jinside

installation blockout L.

13)Place luminaire housing Cinto installation

blockout/mounting ring assembly L/H. Secure

luminaire with mounting ring Hby tightening

screws M.

Warning:

When luminaire is placed inside

installation

blockout L, ensure there is no stress on

sealable junction box Jor electric cables (Fig. IV).

Fig. IV

Fig. V



Fig. VI

Fig. VII

TO9191W0823 © WE-EF 2023

7HFKQLFDOVSHFLĥFDWLRQVDUH

subject to change.

www.we-ef.com

WE-EF LEUCHTEN

Germany

Tel +49 5194 909 0

Fax +49 5194 909 299

[email protected]

WE-EF LUMIERE

France

Tel +33 4 74 99 14 44

Fax +33 4 74 99 14 40

[email protected]

WE-EF SWITZERLAND

Switzerland

Tel +41 22 752 49 94

Fax +41 22 752 49 74

[email protected]

WE-EF LIGHTING

Thailand

Tel +66 2 738 9610

Fax +66 2 175 2174

[email protected]

WE-EF LIGHTING

Australia

Tel +61 3 8587 0444

Fax +61 3 8587 0499

[email protected]

WE-EF LIGHTING

United States of America

Tel +1 724 742 0030

Fax +1 724 742 0035

[email protected]

Andere Handbücher für ETC320-GB LED

Inhaltsverzeichnis

Andere WE-EF Außenleuchte Handbücher

WE-EF

WE-EF AFL100 Series Bedienungsanleitung

WE-EF

WE-EF CTY150 Bedienungsanleitung

WE-EF

WE-EF RLS400 Series Bedienungsanleitung

WE-EF

WE-EF PSY424 LED Bedienungsanleitung

WE-EF

WE-EF LSP434 Bedienungsanleitung

WE-EF

WE-EF XRY324 LED Bedienungsanleitung

WE-EF

WE-EF PSY414 Bedienungsanleitung

WE-EF

WE-EF VFL530 Bedienungsanleitung

WE-EF

WE-EF ZAT400 Series Bedienungsanleitung

WE-EF

WE-EF ETC100-GB LED Series Bedienungsanleitung

WE-EF

WE-EF PSY414 LED Bedienungsanleitung

WE-EF

WE-EF SLS400 Series Bedienungsanleitung

WE-EF

WE-EF VFL500-SE Series Bedienungsanleitung

WE-EF

WE-EF PFL240 LED Bedienungsanleitung

WE-EF

WE-EF ALP534 LED Bedienungsanleitung

WE-EF

WE-EF RFL540-SE LED Series Bedienungsanleitung

WE-EF

WE-EF RFS500 LED Series Bedienungsanleitung

WE-EF

WE-EF QRI354 LED Bedienungsanleitung

WE-EF

WE-EF ETV100 Series Bedienungsanleitung

WE-EF

WE-EF LTM440 LED Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

WE-EF

WE-EF ZTY630 LED Bedienungsanleitung

WE-EF

WE-EF FLA441 LED Bedienungsanleitung

WE-EF

WE-EF FLA780 Bedienungsanleitung

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

NEBO

NEBO NEB-LSP-0020 Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

BEGA

BEGA 84 253 Handbuch

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung

LIGMAN

LIGMAN DE-20023 Bedienungsanleitung