2
Montage
Montage und Wartung darf nur von geschultem Fachper-
sonal mit entsprechender beruflicher Qualifikation in Über-
einstimmung mit den neuesten elektrischen Installations-
und Sicherheitsvorschriften durchgeführt werden.
Die Hinweise der Leuchtmittelhersteller der eingesetzten
Lampe für Betrieb und Wartung sind unbedingt zu beachten.
Bei der Montage direkt auf Beton ist auf eine geeignete
Sperrschicht zum Aluminiumkörper zu achten.
Bei Fragen wenden Sie sich bitte an unsere technische
Hotline unter +49 5194 909209 (Montag - Freitag von
08:00 Uhr bis 16:00 Uhr).
Um einen festen Stand der Leuchte zu gewährleisten ist
das WE-EF Erdstück ESD6 300-0456 zu verwenden.
Vorgehensweise
1) Spannungsfreiheit der Anschlussleitung herstellen.
2) Das Erdstück ausrichten und in dem Boden verankern.
3) Durch Lösen der Befestigungsschraube Adie
Abschlusskappe Bentfernen.
4) Die drei Befestigungsschrauben Cdes Chassis lösen,
den Steckverbinder Dabziehen, das Chassis Eleicht
drehen und nach oben herausnehmen.
5) Die Lampe einsetzen. Lampenleistung und Sockel
müssen mit den Angaben des Leistungsschildes über-
einstimmen.
6) Das Chassis Ewieder einhängen, die Befestigungs-
schrauben Cfest anziehen, Steckverbinder Daufste-
cken, die Abschlusskappe B aufsetzen, die Schraube A
fest anziehen und den Abdeckstopfen einsetzen.
7) Die Leuchte auf das Erdstück befestigen und die
Schrauben mit den beiliegenden Kappen abdecken.
8) Die Anschlusstür Fdurch Lösen der Verriegelungs-
schraube Gentfernen, die Sicherungskappe Hund die
Abdeckung des Anschlusskastens Iabnehmen.
Installation
The luminaire must be installed and maintained by a suit-
ably qualified person in compliance with latest construc-
tion and electrical regulations and relevant legislation.
The given information from the lamp manufacturer about
the correct lamp, operation and maintenance are strictly
to be observed.
For the mounting directly on concrete a suitable insulating
course to the aluminium body is necessary.
In case of questions please contact our technical hotline:
+49 5194 909209 (from Monday - Friday from 08.00 until
16.00 hours.
It is recommended to incorporate the WE-EF planted root
ESD6 300-0456 to facilitate rigid installation.
Installation Procedure
1) Switch off the mains electrical supply.
2) Adjust position of the planted root and fix it to the
ground.
3) Loosen the fixing screws Aand take off the cap B.
4) Loosen the 3 fixing screws Cof the gear tray, take off
the cable connector D, slightly turn the gear tray E
and take off upwards.
5) Carefully insert lamp. Lamp performance and lamp
base have to correspond with the data mentioned on
the label of the luminaire.
6) Re-install the gear tray, firmly tighten the fixing screws
C, insert cable connector D, re-install the cap B, firmly
tighten the fixing screw Aand insert the cover plug.
7) Mount the luminaire to the planted root and cover the
screws with the enclosed caps.
8) Remove the door Fthrough loosening of the locking
screw G, take off the safety cap Hand the cover of the
connecting box I.