Weider Platinum Xp 800 Bedienungsanleitung

Model No. 831.153971

Serial No.

Write the serial number in the

space above for future reference.

Serial Number Decal (under seat)

\_Visit our website at

www.weiderplatin um.com

•Assembly

•Adjustments

•Console Operation

•Part List and Drawing

_CAUTION

Read all precautions and instruc-

tions in this manual before

using this equipment. Save this

manual for future reference.

W E I D E R_

RESISTANCE SYSTEM EXERCISER

User's Manual

Sears, Roebuck and Co., Hoffman Estates, IL 60179

TABLE OF CONTENTS

WARNING DECAL PLACEMENT .......................................................... 2

IMPORTANT PRECAUTIONS ............................................................. 3

BEFORE YOU BEGIN ................................................................... 4

ASSEMBLY ........................................................................... 5

ADJUSTMENTS ...................................................................... 14

CONSOLE OPERATION ................................................................ 18

CABLE DIAGRAM ..................................................................... 20

TROUBLESHOOTING .................................................................. 21

EXERCISE GUIDELINES ............................................................... 22

ORDERING REPLACEMENT PARTS ................................................ Back Cover

FULL TEN-YEAR WARRANTY .................................................... Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin-

ning assembly.

WARNING DECAL PLACEMENT

The decals shown here have been

placed on the resistance system. If a

decal is missing or illegible, please call

1-800-999-3756 to order a free replace-

ment decal. Apply the decal in the loca-

tion shown.

•Misuse of this product may result in serious

injury.

•Read user's manual and follow all warnings

and operating instructions prior to use.

•DO not allow children on or around machine.

•Replace label if damaged, illegible, or removed.

IMPORTANT PRECAUTIONS

before using the resistance system.

t. Read all instructions in this manual before

using the resistance system. Use the resist-

ance system only as described in this manual.

adequately informed of all precautions.

3. The resistance system is intended for home

use only. Do not use the resistance system In

any commercial, rental, or institutional setting.

11. Pull on the lower cable only while sitting on

the bench or standing on the base plate. Pull

on the high cables only while sitting on the

bench, with the seat in one of the three posi-

tions closest to the upright base, or while

standing on the base plate.

12. The resistance system is designed to be

used with the included resistance. Do not

use the resistance system with any other

type of resistance.

surface. Cover the floor beneath the resist-

ance system to protect the floor.

5, Make sure that all parts are properly tight-

ened each time the resistance system is

used. Replace any worn parts immediately.

6, Keep children under 12 and pets away from

the resistance system at all times.

7. Keep hands and feet away from moving parts.

8. Always wear athletic shoes for foot protec-

tion while exercising.

9. The resistance syat_m is designed to sup-

part a maximum user weight of 300 pounds.

10. The crossbar on the top frame is not

designed to be used for pull-up exercises. Do

not hang on the crossbar.

cables when performing an exercise that

does not require it.

14. Make sure the storage knob is in place and

fully tightened each time the resistance sys-

tem is used.

15. Make sure that the cables remain on the pul-

leys at all times. If the cables bind as you are

exercising, stop immediately and make sure

that the cables are on the pulleys.

16. Do not pull on the cables while the resist-

ance level is being adjusted.

17. If you feel pain or dizziness while exercising,

stop Immediately and begin cooling down.

Read all instructions before using. Sears assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

BEFORE YOU BEGIN

Thank you for selectingthe innovative WELDER®PLAT-

INUM XP8O0 resistancesystem.The resistancesystem

offersa selectionofstationsdesignedtodevelop every

majormusclegroupof the body.Whether yourgoal isto

tone yourbody,builddramaticmusclesize and

strength,or improveyourcardiovascularsystem,the

resistancesystemwillhelpyouto achievethe specific

resultsyouwant.

For your benefit, read this manual carefully before

using the resistance system. If you havequestions

after readingthismanual, call 1-800-4-MY-HOME®

(1-800-469-4663). To helpusassistyou, please note

the productmodelnumber and serialnumberbefore

calling. The modelnumberis 831.153971. The serial

numbercan be found on a decal attachedtothe resist-

ance system(see thefrontcoverofthis manual).

Before readingfurther,please reviewthe drawing below

and familiarize yourselfwiththe parts thatare labeled.

Crossbar

Lat Bar

Console

Squat Backrest

Backrest

Storage Knob

Top Frame

High Pulley

-- ResistanceBar

Squat Pin

Low Pulley

Row Plate

Seat

Seat Knob

Base Plate

Leg Level ASSEMBLED

DIMENSIONS:

Height: 82 in.

Width: 66 in.

Depth: 80 in.

ASSEMBLY

This manualisdasigP_dto ensurethatthe resist-

ance systemcan be assembledsuccessfullyby

mostpeople. However,itis importantto realize

that the versatileresistancesystemhasmany

partsand that the assembly processwilltake

time. Most peoplefind_at bysettingaside plenty

oftime, assemblywillgo sm_ly.

Before beginning assembly, carefully read the

following information and instructions:

•Assembly requires two persons.

• Place all parts in acleared area and remove the

packing materials. Do not dispose of the packing

matedals untilassembly is completed.

•For help identifying small parts, use the PART

IDENTIFICATION CHART. Note: Some small

parts may have been pre-attached for shipping. If

a part is not in the parts bag, check to see if it

has been pre-attached.

•Tightenall parts as you assemble them, unless

instructedtodo otherwise.

• As you assemble the resistance system, make

sure all parts are orientedas shown in the draw-

ings.

The included Allen w_ _and the fol-

lowing tools (not included) are required for

assembly:

•Two adjustable wrenches

•One rubber mallet

• One standard screwdriver

•One Phillips screwdriver

•Lubricant, such as grease or petroleum jelly,

and soapy water,

Assemblywillbe more convenientifyou have a

socketset, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

Attach the Base Plate Foot (63) to the Base Plate

(1) with two M4 x 38mm Screws (100).

2. Attach a Wheel (65) to a Wheel Insert (64) with an

M10 x78mm Button Bolt (99) and an M1O Nylon

Locknut (103). Do not overtighten the Locknut;

the Wheel must be able to turn easily.

Attach the Wheel Insert (64) to the Base Plate (1)

with two M4 x 16mm Screws (53) and a Plastic

Foot (36).

Attach the other Wheel (65) in the same man-

ner.

100 p

_.-1 OO

103

3. 3

Insert the Upper Wire Harness (71) throughthe

hole in the Upright Cover (3). Pull the lower end

of the Upper Wire Harness out of the hole in the

back of the Upright (2).

Attach the Upright Cover (3) and Upright (2) to

the Base Plate (1) with an M10 x 25mm Button

Screw (88), an MIO Washer (106), an M10 x

92mm Button Bolt (83), and an M10 Nylon

Locknut (103).

4. Attach the Row Plate (28) to the Upright (2) with

four M10 x 75ram Button Bolts (84) and four MI0

Nylon Locknuts (103).

103

I O3

5. Insert the four connectorsofthe lowerwire har-

ness (C) into the socketsofthe Upper Wire

Harness (71). The connectors should slide easi-

ly into the sockets and snap into place. If a con-

nector does not slide easily and snap into place,

turn the connector over and then insert it.

Make sure that the connectorsand wires appear

as shown in the inset drawing. IF THE CONNEC-

TORS ARE NOT INSERTED PROPERLY, THE

CONSOLE MAY BE DAMAGED WHEN THE

POWER IS TURNED ON.

Pull the excess lower wire hamess ('Cl out of

the Mech Frame 1'61and Push it and the UDDer

Wire Harness (71_ into the Uoriaht (2_.

Insert the Mech Frame (6) into the Base Plate (1).

Attach the Mech Frame to the Upright(2) with a

1/2"x 25mm Screw (85) and a 1/2"Lock Washer

(12). Do not tighten the Screw yet.

Attach the Mech Frame (6) to the Base Plate (1)

withfour M10 Nylon Locknuts(103).

Tighten the 1/2" x 25mm Screw (85).

6. Attach the Leg Lever Bumper (55) to the Leg (5)

with two M5 x 56mm Screws (108).

7, Pullthe Seat Knob (48) and remove the Seat

Carriage (44) from the Rail (not shown).

Attach the Seat (45) to the Seat Carriage (44)

withfour M6 x 16mm Screws (41).

6 12

Pull the Seat Knob (48) out and slide the Seat

Carriage (44) onto the Rail (4) as shown. Engage

the Knob into a hole in the Rail.

Press the Rail Cap (49) onto the Leg (5). Attach

the Leg to the Rail (4) with two M10 x 64mm

Button Bolts (80), four M10 Washers (106), and

two M10 Nylon Locknuts (103).

9. Attach the Rail Insert (31) insideof the Rail (4)

with two M10 x 64mm Button Bolts (80), four M10

Washers (106), and two M10 Nylon Locknuts

(103). Make sure the Bolts go through the indi-

cated holes in the Rail Insert.

10. Lubricate an M10 x 125mm Button Bolt (89) with

grease. Attach the Rail (4) to the Row Plate (28)

with the Bolt, two M10 Washers (106), two 31mm

Spacers (30), and an M10 Nylon Locknut (103).

Do not overtighten the Locknut; the Rail must

be able to pivot easily.

Tighten the Storage Knob (29) into the Row Plate

(28) and the Rail (4).

11. Wet a Squat Arm (20) with soapy water. Slide a

Small Foam Pad (24) and a Short Handgrip (21)

onto the Squat Arm.

Repeat with the other Squat Arm (20).

Tighten the Squat Knob (27) into the Squat

Carriage (19) and the Squat Arm Pivot Tube (not

shown).

103 106 4

" Holes on

106 this side

49 80

103 106

Holes

106

30 106 89

Lubricate

12. Attach the Squat Backrest(25) to the Squat

Carriage (19) with four M6 x 16mm Screws (41).

13. Insert the Squat Pin (66) into the Upright (2).

Slide the Squat Carriage (19) onto the Upright (2).

14. Attach the Top Frame (37) to the Upright (2) with

two M10 x 25mm Button Screws (88), an M10 x

75mm Button Screw (84), three M10 Lock

Washers (75), and an M10 Washer (106).

15. Pull the excess Upper Wire Harness (71) out of

the Upright (2). Insertthe connector on the

Console (67) intothe socketon the Upper Wire

Harness. The connector should slide easily into

the socket and snap into place. Iftheconnector

does not slideeasilyand snap intoplace,turnthe

connector over and then insert it.

Make sure thatthe connector and wires appear

as shown in the inset drawing. IF THE CONNEC-

TOR IS NOT INSERTED PROPERLY, THE CON-

SOLE MAY BE DAMAGED WHEN THE POWER

IS TURNED ON.

Push the excess Upper Wire Harness (71) into

the Upright (2).

Attach the Console (67) to the Upright (2) with

four M4 x 70ram Screws (114).

16. Attach a Large Pulley (14) and the Pulley Plate

(68) to the Upright (2) with an M12 x 62mm

Button Bolt (81) and an M12 Nylon Locknut (43).

Do not tighten the Locknut yet.

17. Pull the upper cable (A), which is attached inside

of the Mech Frame (not shown), up between the

Updght (2) and the Pulley Plate (68).

Attach another Large Pulley (14) to the Upright (2)

and PulleyPlate (68) with an M12 x 62mm Button

Bolt (81) and an M12 Nylon Locknut (43). Make

sure that the upper cable (A) is between the

two Pulleys.

Hold the 38mm Spacer (90) insidethe loop ofthe

upper cable (A), and between the Upright(2) and

the Pulley Plate (68). Attach the Spacer with an

M1Ox 58mm Button Screw (42). Make sure the

ends of the cable do not wrap around each

other below the Spacer and the Large Pulleys

(14) used in steps 16 and 17 (refer to the

CABLE DIAGRAM on page 20).

Tighten the M12 Nylon Locknuts (43) used in

steps 16 and 17.

18. Attach aSmall Guide Spacer (18), a LargeGuide

Spacer (17), and two Bar Guides (15) to the

Upright (2) with an M10 x 152mm Bolt(86).

Pull the upper cable (A) up between the Bar

Guides (15). Press the metal cover on the cable

into the groove in the BlockSpacer (16). Attach a

Small Guide Spacer (18), the Block Spacer, the

two Bar Guides (15), an M10 Thick Washer (54),

and the two Tethers (70) to the Upright (2) with

another M10 x 152mm Bolt (86). Do not tighten

the Bolt yet.

114

_43

17 ._

18 86

Metal 54

18 16 Groove

Andere Handbücher für Platinum Xp 800

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weider Fitnessgeräte Handbücher

Weider

Weider XR20 Bedienungsanleitung

Weider

Weider Pro 9655 Bedienungsanleitung

Weider

Weider PowerPak WEMC06740 Bedienungsanleitung

Weider

Weider 8525 Bedienungsanleitung

Weider

Weider Total BodyWorks 5000 Bedienungsanleitung

Weider

Weider WEBE0878.0 Bedienungsanleitung

Weider

Weider Wesy70072powermax Bedienungsanleitung

Weider

Weider Pro 340 L Bench Bedienungsanleitung

Weider

Weider Pro 205 Bedienungsanleitung

Weider

Weider Victory X41 Bedienungsanleitung

Weider

Weider CrossBow ADVANTAGE Bedienungsanleitung

Weider

Weider 130 Tc Bench Bedienungsanleitung

Weider

Weider FLEX CXT 1112 Bedienungsanleitung

Weider

Weider Pro Pt 800 Bench Bedienungsanleitung

Weider

Weider 831.15395.0 Bedienungsanleitung

Weider

Weider WESY1938.1 Bedienungsanleitung

Weider

Weider Pro Pt 800 Bench Systemhandbuch

Weider

Weider 130 Tc Bench Bedienungs- und Wartungshandbuch

Weider

Weider Pro 9450 Bedienungs- und Wartungshandbuch

Weider

Weider PRO 800 Bedienungsanleitung

Weider

Weider Pro 6900 Bedienungsanleitung

Weider

Weider WESY1938C.0 Bedienungsanleitung

Weider

Weider Victory Club Series 320 Bedienungsanleitung

Weider

Weider CROSS BAR MAX Bedienungsanleitung

Beliebte Fitnessgeräte Handbücher anderer Marken

NSD

NSD PB-188P Bedienungsanleitung

Performance

Performance HyperVibe Bedienungsanleitung

Scalamobil

Scalamobil S27 Bedienungsanleitung

Precor

Precor Experience Series Bedienungsanleitung

FYTTER

FYTTER RedMIUM BENCH BE-T6R Bedienungsanleitung

Taurus

Taurus TF-RK1312 Bedienungsanleitung

Nustep

Nustep T5 Bedienungsanleitung

Precor

Precor CW-507 Bedienungsanleitung

Movement

Movement BICEPS Idea Bedienungsanleitung

Kegel8

Kegel8 V For Men Bedienungsanleitung

BLK BOX

BLK BOX 21-0122-0B Bedienungsanleitung

Stamina

Stamina aeropilates premier 299 Bedienungsanleitung

SPORTSTECH

SPORTSTECH PBX300 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 877102 Bedienungsanleitung

Weslo

Weslo Gym 650 Bedienungsanleitung

Rebel

Rebel ACTIVE RBA-1011 Bedienungsanleitung

4iiii

4iiii FLiiiight Bedienungsanleitung

Image

Image 540 Bedienungsanleitung