Weslo Momentum5.9 Elliptical Bedienungsanleitung

258868 258869 258870 258871

USERʼS MANUAL

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. eep this manu-

al for future reference.

Model No. WLEL32909.2

Serial No.

Write the serial number in the

space above for reference.

www.workoutwarehouse.com

Serial Number

Decal

QUESTIONS?

If you have questions, or if parts are

damaged or missing, DO NOT

CONTACT THE STORE; please

contact Customer Care.

IMPORTANT: Please register this

product (see the limited warranty

on the back cover of this manual)

before contacting Customer Care.

CALL TOLL-FREE:

1-866-699-3756

Mon.–Fri., 6 a.m.–6 p.m. MT

Sat. 8 a.m.–4 p.m. MT

ON THE WEB:

www.wesloservice.com

TABLE OF CONTENTS

WARNINGDECA P ACEMENT ..............................................................2

IMPORTANTPRECAUTIONS ................................................................3

BEFOREYOUBEGIN ......................................................................4

ASSEMB Y ...............................................................................5

HOWTOUSETHEE IPTICA .............................................................14

MAINTENANCEANDTROUB ESHOOTING ...................................................19

EXERCISEGUIDE INES ...................................................................21

PART IST ..............................................................................22

EXP ODEDDRAWING ....................................................................23

ORDERINGREP ACEMENTPARTS ..................................................BackCover

IMITEDWARRANTY ..............................................................BackCover

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the

warning decal(s). If a decal is missing or

illegible, see the front cover of this

manual and request a free replacement

decal. Apply the decal in the location

shown. Note: The decal(s) may not be

shown at actual size.

WES O is a registered trademark of ICON IP, Inc.

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your elliptical before using your elliptical. ICON

assumes no responsibility for personal injury or property damage sustained by or through the use of

this product.

IMPORTANT PRECAUTIONS

1. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or

persons with pre-existing health problems.

2. Use the elliptical only as described in this

manual.

3. It is the responsibility of the owner to ensure

that all users of the elliptical are adequately

informed of all precautions.

4. The elliptical is intended for home use only.

Do not use the elliptical in a commercial,

rental, or institutional setting.

5. eep the elliptical indoors, away from

moisture and dust. Do not put the elliptical in

a garage or covered patio, or near water.

6. Place the elliptical on a level surface, with at

least 3 ft. (0.9 m) of clearance in the front

and rear of the elliptical and 2 ft. (0.6 m) on

each side. To protect the floor or carpet from

damage, place a mat under the elliptical.

7. Inspect and properly tighten all parts

regularly. Replace any worn parts

immediately.

8. eep children under age 12 and pets away

from the elliptical at all times.

9. The elliptical should not be used by persons

weighing more than 250 lbs. (113 kg).

10. Wear appropriate clothes while exercising;

do not wear loose clothes that could become

caught on the elliptical. Always wear athletic

shoes for foot protection while exercising.

11. Hold the handlebars or the upper body arms

when mounting, dismounting, or using the

elliptical.

12. The pulse sensor is not a medical device.

Various factors may affect the accuracy of

heart rate readings. The pulse sensor is

intended only as an exercise aid in

determining heart rate trends in general.

13. The elliptical does not have a freewheel; the

pedals will continue to move until the

flywheel stops. Reduce your pedaling speed

in a controlled way.

14. eep your back straight while using the

elliptical; do not arch your back.

15. Over exercising may result in serious injury

or death. If you feel faint or if you experience

pain while exercising, stop immediately and

cool down.

BEFORE YOU BEGIN

Pulse Sensor

Upper Body Arm

Pedal Disc

*Water bottle is not included

Pedal

Wheel

Console

Water Bottle Holder*

Thank you for selecting the new WES O®

MOMENTUM CT 5.9 elliptical. The MOMENTUM CT

5.9 provides a selection of features designed to make

your workouts at home more effective and enjoyable.

For your benefit, read this manual carefully before

you use the elliptical. If you have questions after

reading this manual, please see the front cover of this

manual. To help us assist you, note the product model

number and serial number before contacting us. The

model number and the location of the serial number

decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

eveling Foot

Handlebar

M10 Split

Washer (45)–2

M10 Locknut

(33)–2

M10

Washer (83)–2

M8 Locknut

(38)–8

M8 x 43mm Button Bolt (50)–6

M10 x 25mm

Patch Screw (40)–2

M10 x 78mm Button Bolt (34)–4

Small Wave

Washer (69)–2

M8 Split

Washer (28)–6

M8 x 25mm Patch

Screw (56)–2

M8 Washer

(55)–8

M8 x 80mm Patch Bolt (79)–2

M6 Bolt Set (25)–2

Large Wave

Washer (76)–2

M10 x 74mm Button Bolt (7)–2

M4 x 10mm

Blunt Screw

(82)–2

M4 x 16mm

Self-tapping

Screw (52)–10

M6 x 13mm

Patch Screw

(81)–2

M8 x 14mm Button

Screw (27)–6

ASSEMBLY

To hire an authorized service technician to assemble the elliptical, call 1-800-445-2480.

Assembly requires two persons. Place all parts of the elliptical in a cleared area and remove all packing mate-

rials; do not dispose of the packing materials until assembly is completed.

In addition to the included tool(s), assembly requires a Phillips screwdriver , an adjustable

wrench , and a rubber mallet .

See the drawings below to identify the small parts needed for assembly. The number in parentheses below each

drawing is the key number of the part, from the PART IST near the end of this manual. The number following

the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if

it has been preassembled. To avoid damaging parts, do not use power tools for assembly.

2. Insert the Front Stabilizer Cover (68) into the

Front Stabilizer (63).

Attach the Front Stabilizer Cover (68) with two

M4 x 16mm Self-tapping Screws (52).

3. While a second person lifts the rear of the

Frame (1), attach the Rear Stabilizer (9) to the

Frame with two M10 x 78mm Button Bolts (34).

Identify the Front Stabilizer (63), which has

Wheels (21).

Orient the Front Stabilizer (63) so that the small

holes face downward.

While a second person lifts the front of the

Frame (1), attach the Front Stabilizer (63) to the

Frame with two M10 x 78mm Button Bolts (34).

Small

Holes

To make assembly easier, read the

information on page 5 before you begin.

4. Insert the Rear Stabilizer Cover (67) into the

Rear Stabilizer (9).

Attach the Rear Stabilizer Cover (67) with two

M4 x 16mm Self-tapping Screws (52).

5. Orient the Upright (2) as shown. Have a second

person hold the Upright near the Frame (1).

See the inset drawing. ocate the wire tie in

the Upright (2). Tie the lower end of the wire tie

to the Wire Harness (73). Next, pull the upper

end of the wire tie upward out of the top of the

Upright. Then, untie and discard the wire tie.

Tip: To prevent the Wire Harness (73) from

falling into the Upright (2), secure the Wire

Harness with a rubber band or a piece of

tape.

Slide the Upright (2) onto the Frame (1).

Tip: Avoid pinching the Wire Harness (73).

Attach the Upright (2) with two M10 x 74mm

Button Bolts (7), two M10 Split Washers (45),

and two M10 ocknuts (33). Do not tighten the

Button Bolts yet.

Wire Tie

Avoid pinching the

Wire Harness (73)

6. Attach the Water Bottle Holder (29) to the

Upright (2) with two M4 x 16mm Self-tapping

Screws (52).

Identify and orient the Console Cover (88) as

shown.

Slide the Console Cover (88) onto the Upright

(2).

7. Identify the eft and Right Handlebars (85, 86),

which are marked with “ eft” and “Right” stick-

ers.

While a second person holds the eft and Right

Handlebars (85, 86) near the Upright (2), insert

the Pulse Wires (84) into the holes in the

Upright and pull them upward out of the Upright.

Tip: Avoid pinching the wires. Attach the eft

and Right Handlebars (85, 86) to the Upright (2)

with an M8 x 80mm Patch Bolt (79) and an M8

ocknut (38). Do not tighten the Patch Bolt

yet.

Make sure that the M8 x 80mm Patch Bolt

(79) is inserted through the bottom hole in

the Left and Right Handlebars (85, 86) and

the Upright (2).

Avoid pinching

the wires

9. The Console (23) can use four D batteries (not

included); alkaline batteries are recommended.

IMPORTANT: If the Console has been

exposed to cold temperatures, allow it to

warm to room temperature before inserting

batteries. Otherwise, you may damage the

console displays or other electronic compo-

nents. Remove the battery cover and insert the

batteries into the battery compartment. Make

sure to orient the batteries as shown by the

diagram inside the battery compartment.

Then, reattach the battery cover.

To purchase an optional power adapter, call

the telephone number on the front cover of

this manual. To avoid damaging the console,

use only a manufacturer-supplied power

adapter. Plug one end of the power adapter

into the jack on the console; plug the other end

into an outlet installed in accordance with all

local codes and ordinances.

Batteries

Battery

Cover

8. While a second person holds the Console Plate

(75) near the Upright (2), insert the Wire

Harness (73) and the Pulse Wires (84) upward

through the Console Plate.

Tip: Avoid pinching the wires. Attach the

Console Plate (75) to the Upright (2) with two

M6 x 13mm Patch Screws (81).

73, 84

Avoid pinching

the wires

10. While another person holds the Console (23)

near the Upright (2), connect the console wires

to the Wire Harness (73) and to the Pulse Wires

(84).

Insert the excess wire into the Console (23) or

the Upright (2).

Tip: Avoid pinching the wires. See the lower

drawing. Attach the Console (23) to the Console

Plate (75) with four M4 x 16mm Self-tapping

Screws (52).

Console Wires

73, 84

Avoid pinching

the wires

11. Finish attaching the eft and Right Handlebars

(85, 86) to the Upright (2) with an M8 x 80mm

Patch Bolt (79) and an M8 ocknut (38).

Tip: While inserting the M8 x 80mm Patch

Bolt (79), avoid pinching or damaging the

wires inside the Upright (2).

Tighten both M8 x 80mm Patch Bolts (79).

Andere Handbücher für Momentum5.9 Elliptical

Dieses Handbuch passt für folgende Modelle

Andere Weslo Ellipsentrainer Handbücher

Weslo

Weslo Momentum 750 Elliptical Bedienungsanleitung

Weslo

Weslo Momentum 7.0 Ex Elliptical Bedienungsanleitung

Weslo

Weslo Body Shop 2 Bedienungsanleitung

Weslo

Weslo Momentum 4.0 Elliptical Bedienungsanleitung

Weslo

Weslo Momentum R 7.8 Elliptical Bedienungsanleitung

Weslo

Weslo Momentum5.0 Elliptical Benutzerhandbuch

Weslo

Weslo EasyFit WLIVEL86172.0 Bedienungsanleitung

Weslo

Weslo MOMENTUM 730 ELLIPTICAL EXERCISER... Bedienungsanleitung

Weslo

Weslo 8.25 Elliptical Bedienungsanleitung

Weslo

Weslo Momentum 710 Elliptical Bedienungsanleitung

Weslo

Weslo WLEL45070 Bedienungsanleitung

Weslo

Weslo Momentum 410 Elliptical Bedienungs- und Wartungshandbuch

Weslo

Weslo Momentum 410 Elliptical Bedienungsanleitung

Weslo

Weslo gllider III Bedienungsanleitung

Weslo

Weslo MOMENTUM ELLIPTICAL Bedienungsanleitung

Weslo

Weslo WLEL71807.0 Bedienungsanleitung

Weslo

Weslo Momentum 800 Elliptical Bedienungsanleitung

Weslo

Weslo Momentum R 5.2 Elliptical Benutzerhandbuch

Weslo

Weslo ALTA Bedienungsanleitung

Weslo

Weslo MOMENTUM CT 5.0 Bedienungsanleitung

Weslo

Weslo Momentum 850 Elliptical Bedienungsanleitung

Weslo

Weslo Eclipse 2 WLEMEL45071 Bedienungsanleitung

Weslo

Weslo Momentum 405 Elliptical Bedienungsanleitung

Weslo

Weslo MOMENTUM CT 5.0 Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

Precor

Precor Resolute RSL 620 Bedienungsanleitung

NordicTrack

NordicTrack E 9.2 Elliptical Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung

Reebok

Reebok 1000 Zx Elliptical Bedienungsanleitung