Weslo Cadence 255 Dr Treadmill Bedienungsanleitung

Model No. WLTL21104.2

Serial No.

Write the serial number in the

space above for future reference.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

Serial Number

Decal

QUESTIONS?

If you have questions, or if there

are missing parts, we will guar-

antee complete satisfaction

through direct assistance from

our factory.

TO AVOID DELAYS, PLEASE

CALL DIRECT TO OUR TOLL-

FREE CUSTOMER HOT LINE.

The trained technicians on our

Customer Hot Line will provide

immediate assistance, free of

charge to you.

CUSTOMER HOT LINE:

1-866-699-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

Visit our website at

www.weslo.com

new products, prizes,

fitness tips, and much more!

USER'S MANUAL

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Place the treadmill on a level surface, with at

least eight feet of clearance behind it and two

feet on each side. Do not place the treadmill

on any surface that blocks air openings. To

protect the floor or carpet from damage,

place a mat under the treadmill.

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should not be used by persons

weighing more than 250 pounds.

8. Never allow more than one person on the

treadmill at a time.

9. Wear suitable exercise clothes when using

the treadmill. Do not wear loose clothes that

could become caught in the treadmill.

Athletic support clothes are recommended

for both men and women. Always wear athlet-

ic shoes. Never use the treadmill with bare

feet, wearing only stockings, or in sandals.

10. When connecting the power cord (see page 8),

plug the power cord into a surge suppressor

(not included) and plug the surge suppressor

into a grounded circuit capable of carrying 15

or more amps. No other appliance should be

on the same circuit. Do not use an extension

cord.

11. Use only a single-outlet surge suppressor that

meets all of the specifications described on

page 8. To purchase a surge suppressor, see

your local WESLO dealer or call 1-866-699-

3756 and order part number 146148, or see

your local electronics store.

12. Failure to use a properly functioning surge

suppressor could result in damage to the con-

trol system of the treadmill. If the control sys-

tem is damaged, the walking belt may change

speed, accelerate, or stop unexpectedly,

which may result in a fall and serious injury.

13. Keep the power cord and the surge suppres-

sor away from heated surfaces.

14. Never move the walking belt while the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See page 4

if the treadmill is not working properly.)

15. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the

handrails while using the treadmill.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read

the following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

16. The treadmill is capable of high speeds.

Adjust the speed in small increments to

avoid sudden jumps in speed.

17. Never leave the treadmill unattended while it is

running. Always remove the key and unplug

the power cord when the treadmill is not in

use.

18. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 5, and HOW TO MOVE

THE TREADMILL on page 11.) You must be

able to safely lift 45 pounds (20 kg) to raise,

lower, or move the treadmill.

19. Do not change the incline of the treadmill by

placing objects under the treadmill.

20. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

21. Inspect and properly tighten all parts of the

treadmill regularly.

22. Never drop or insert any object into any

opening.

23. DANGER: Always unplug the power

cord immediately after use, before cleaning

the treadmill, and before performing the

maintenance and adjustment procedures

described in this manual. Never remove the

motor hood unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorized ser-

vice representative only.

24. This treadmill is intended for in-home use

only. Do not use this treadmill in any com-

mercial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician.

This is especially important for persons over the age of 35 or persons with pre-existing health prob-

lems. Read all instructions before using. ICON assumes no responsibility for personal injury or prop-

erty damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

The decals shown have been placed on your treadmill. If a decal is missing, or if it is not legible, please

call toll-free 1-866-699-3756 to order a free replacement decal. Apply the decal in the location shown.

Note: The decals are not shown at actual size.

BEFORE YOU BEGIN

Handrail

Console

Storage Latch

Key/Clip

Circuit Breaker

Walking Belt

Foot Rails

Incline Leg

Power Cord

FRONT

BACK

RIGHT SIDE

Rear Roller

Adjustment Bolts

Water Bottle Holder

(Bottle not included)

Upright

Thank you for selecting the WESLO®CADENCE 255

DR treadmill. The CADENCE 255 DR treadmill com-

bines advanced technology with innovative design to

let you enjoy an excellent form of cardiovascular exer-

cise in the convenience and privacy of your home. And

when you’re not exercising, the unique CADENCE 255

DR treadmill can be folded up, requiring less than half

the floor space of other treadmills.

For your benefit, read this manual carefully before

using the treadmill. If you have questions after read-

ing this manual, please call our Customer Service

Department toll-free at 1-866-699-3756, Monday

through Friday, 6 a.m. until 6 p.m. Mountain Time

(excluding holidays). To help us assist you, please note

the product model number and serial number before

calling. The model number of the treadmill is

WLTL21104.2. The serial number can be found on a

decal attached to the treadmill (see the front cover of

this manual for the location).

Before reading further, please review the drawing

below and familiarize yourself with the labeled parts.

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not

dispose of the packing materials until assembly is completed.

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a

small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a nor-

mal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply

wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included allen wrenches and your own phillips screwdriver ,

wire cutters , and needlenose pliers .

To identify small parts, use the PART IDENTIFICATION CHART attached in the center of this manual.

Note: If a part is not in the parts bag, first check to see if it has been pre-assembled.

2. Insert one of the Extension Legs (15) into the treadmill

as shown. Make sure that the Base Pad (33) is on the

indicated side. Note: It may be helpful to tip the Uprights

(38) in the direction shown by the arrow as you insert

the Extension Leg.

Attach the Extension Leg (15) with an Extension Leg

Screw (14). Make sure to push on the head of the

Extension Leg Screw while tightening it.

Attach the other Extension Leg (15) in the same way.

1. Make sure that the power cord is unplugged.

With the help of a second person, carefully raise the

Uprights (38) until the treadmill is in the position shown.

Cut the plastic tie (not shown) off the right Upright (38).

3. If there are plastic ties in the brackets on the Handrails

(4), remove the plastic ties. Hold one of the Handrails

near the right Upright (38) as shown. Insert the Wire

Harness (53) up through the bracket on the Handrail and

out of the round hole in the side of the Handrail. If nec-

essary, use needlenose pliers to pull the Wire Harness

out of the hole. Be careful not to damage the Wire

Harness.

Insert the brackets on the Handrails (4) into the upper

ends of the Uprights (38).

Finger tighten four 1” Bolts (16) with Handrail Washers

(40) into the Uprights (38) and the Handrails (4) as

shown.

Connectors

Bracket

Plastic Ties

4. Set the Console Base (87) on the Handrails (4). Thread

four 3/4” Screws (5) into the Handrails and the Console

Base. After you have started all four Screws, tighten the

Screws until they are snug; do not overtighten the

Screws. Note: It may be helpful to press down on the

top of the Console Base above the Handrails as you

tighten the Screws.

See step 3. Firmly tighten, but do not overtighten,

the four 1” Bolts (16).

Insert the Wire Harness (53) through the two indicated

plastic ties on the Console Base (87) and up through the

hole in the Console Base as shown.

5. Hold the Console (11) near the Console Base (87).

Touch the right Handrail (4) to discharge any static.

Next, insert the Wire Harness (53) through the plastic tie

labeled C in the drawing at the right.

Locate the two connectors on the Wire Harness (53).

Plug the wider connector into the connector labeled Ain

the drawing at the right (see drawing 5b). The connec-

tors should slide together easily and snap into

place. If they do not, turn the connector on the Wire

Harness and try again. Insert the other connector

through the plastic tie labeled D; plug the connector into

the connector labeled B (see drawing 5c). IF THE CON-

NECTORS ARE NOT INSERTED PROPERLY, THE

CONSOLE MAY BE DAMAGED WHEN THE POWER

IS TURNED ON.

See drawing 5a. Pull any slack in the Wire Harness (53)

through the two ties. Make sure that the end of the Wire

Harness indicated by the arrow is routed as shown.

Securely tighten the plastic ties around the Wire

Harness. Cut off the end of each plastic tie.

Tie

53 A

Tie

Tie C Tie D

66 5

7. Attach the Storage Latch (66) to the left Upright (38)

with two 3/4” Screws (5).

8. Make sure that all parts used in assembly are properly tightened before you use the treadmill. Keep

the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page

13). To protect the floor or carpet, place a mat under the treadmill.

Screw

6. Set the Console (11) in the Console Base (87). Make sure

that no wires are pinched. Insert as much of the Wire

Harness (53) as possible down into the hole in the right

Handrail (4). Securely tighten the plastic tie nearest to

the right Handrail. Pull any excess Wire Harness

between the plastic ties tight and tighten the other plastic

tie. Cut off the ends of the plastic ties. Cover the Wire

Harness with the Wire Cover (10), and route the Wire

Harness out of the hole in the side of the Wire Cover.

Attach the Wire Cover to the back of the Console Base

with two 3/4” Screws (5). Do not overtighten the Screws.

Make sure that no wires are pinched before you

attach the Console (11) to the Console Base (87).

Tighten five 3/4” Screws (5) into the Console Base and

the Console in the locations shown. Note: No 3/4”

Screw goes into the hole indicated by the arrow. Do

not overtighten the Screws.

Ties

OPERATION AND ADJUSTMENT

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high-

performance lubricant. IMPORTANT: Never apply sil-

icone spray or other substances to the walking

belt or the walking platform. Such substances will

deteriorate the walking belt and cause excessive

wear.

HOW TO PLUG IN THE POWER CORD

Your treadmill, like any other type of sophisticated

electronic equipment, can be seriously damaged by

sudden voltage changes in your home’s power.

Voltage surges, spikes, and noise interference can

result from weather conditions or from other appli-

ances being turned on or off. To decrease the pos-

sibility of your treadmill being damaged, always

use a surge suppressor with your treadmill (see

drawing 1 at the right). To purchase a surge sup-

pressor, see your local WESLO dealer or call 1-

866-699-3756 and order part number 146148, or see

your local electronics store.

Use only a single-outlet surge suppressor that is

UL 1449 listed as a transient voltage surge sup-

pressor (TVSS). The surge suppressor must have a

UL suppressed voltage rating of 400 volts or less

and a minimum surge dissipation of 450 joules.

The surge suppressor must be electrically rated for

120 volts AC and 15 amps. There must be a moni-

toring light on the surge suppressor to indicate

whether it is functioning properly. Failure to use a

properly functioning surge suppressor could result

in damage to the control system of the treadmill. If

the control system is damaged, the walking belt

may change speed, accelerate, or stop unexpect-

edly, which may result in a fall and serious injury.

This product must be grounded. If it should mal-

function or break down, grounding provides a path of

least resistance for electric current to reduce the risk

of electric shock. This product is equipped with a cord

having an equipment-grounding conductor and a

grounding plug. Plug the power cord into a surge

suppressor, and plug the surge suppressor into an

appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances. Important: The treadmill is not com-

patible with GFCI-equipped outlets.

This product is for use on a nominal 120-volt circuit,

and has a grounding plug that looks like the plug illus-

trated in drawing 1 below. A temporary adapter that

looks like the adapter illustrated in drawing 2 may be

used to connect the surge suppressor to a 2-pole

receptacle as shown in drawing 2 if a properly

grounded outlet is not available.

The temporary adapter should be used only until a

properly grounded outlet (drawing 1) can be installed

by a qualified electrician.

The green-colored rigid ear, lug, or the like extending

from the adapter must be connected to a permanent

ground such as a properly grounded outlet box cover.

Whenever the adapter is used it must be held in place

by a metal screw. Some 2-pole receptacle outlet

box covers are not grounded. Contact a qualified

electrician to determine if the outlet box cover is

grounded before using an adapter.

DANGER: Improper connection

of the equipment-grounding conductor can

result in an increased risk of electric shock.

Check with a qualified electrician or service-

man if you are in doubt as to whether the

product is properly grounded. Do not modify

the plug provided with the product—if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician.

Grounded Outlet Box

Grounding Plug

Surge Suppressor

Grounding Pin

Adapter

Lug

Metal Screw

Grounded Outlet

Grounding Pin

DIAGRAM OF THE CONSOLE

Speed Control

Incline Control

Displays

STEP-BY-STEP CONSOLE OPERATION

Before operating the console, make sure that the

power cord is properly plugged in (see page 8).

Next, locate the circuit break-

er near the power cord. Make

sure that the circuit breaker is

in the reset position.

Stand on the foot rails of

the treadmill. Find the

clip attached to the key,

and slide the clip onto

the waistband of your

clothes.

Next, insert the key fully into the console. After a

moment, the displays will light. Test the clip by care-

fully taking a few steps backward until the key is

pulled from the console. If the key is not pulled

from the console, adjust the position of the clip.

Follow the steps below to operate the console.

Insert the key fully into the console.

A few seconds after the key is inserted, the dis-

plays will light.

Press the Speed

button to start the walking

belt.

Amoment after the button is pressed, the walking

belt will begin to move. Hold the handrails and

begin walking.

CAUTION: Before operating the

console, read the following precautions.

•Do not stand on the walking belt when turn-

ing on the power.

•Always wear the clip (see the drawing at the

right) while operating the treadmill.

• Adjust the speed in small increments to

avoid sudden jumps in speed.

• To reduce the possibility of electric shock,

keep the console dry. Avoid spilling liquids

on the console and place only a sealed

water bottle in the water bottle holder.

Key

Reset

Note: If there is a thin sheet of

plastic on the console, remove it.

Clip

As you exercise, change the speed of the walking

belt as desired by pressing the Speed buttons.

Each time a button is pressed, the speed setting

will change by 0.1 mph; if a button is held down,

the speed setting will change in increments of 0.5

mph. Note: The console can display speed and

distance in either miles or kilometers (see

CALORIES/SPEED DISPLAY at the right). For

simplicity, all instructions in this section refer

to miles.

To stop the walking belt, press the Stop button.

The Time/Distance display will begin to flash.

Note: During the first few minutes that the treadmill

is used, inspect the alignment of the walking belt,

and align it if necessary (see page 13).

Change the incline of the treadmill as desired.

To change the incline of the treadmill, press either

of the Incline buttons until the desired incline level

is reached.

Follow your progress with the displays.

Time/Distance

display—This display

shows the elapsed time

and the distance that you

have walked or run. The

display will change from

one number to the other

every few seconds, as shown by the mode indica-

tors. When the Stop button is pressed, the display

will flash.

Calories/Speed

display—This display

shows the approximate

number of calories you

have burned and the

speed of the walking

belt. The display will change from one number to

the other every few seconds, as shown by the

mode indicators.

Note: The console can

display speed and dis-

tance in either miles or

kilometers. To change

the unit of measurement,

hold down the Stop but-

ton, insert the key into the console, and continue to

hold the Stop button for a moment. An “E” for

English miles or an “M” for metric kilometers will

appear in the Calories/Speed display. Press the

Speed

button to change the unit of measure-

ment. When the desired unit of measurement is

selected, remove the key and then reinsert it.

To reset the displays, press the Stop button,

remove the key, and then reinsert the key.

When you are finished exercising, remove the

key.

Step onto the foot rails, press the Stop button, and

remove the key from the console. Keep the key in a

secure place.

Mode Indicator

Andere Handbücher für Cadence 255 Dr Treadmill

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weslo Tretmühle Handbücher

Weslo

Weslo CADENCE C44 Bedienungsanleitung

Weslo

Weslo Cadence S6 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence M6 Elliptical Bedienungsanleitung

Weslo

Weslo Cadence 6.9 Ery Treadmill Benutzerhandbuch

Weslo

Weslo WLTL10091 Bedienungsanleitung

Weslo

Weslo Cadence 1020 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 21.5 Treadmill Benutzerhandbuch

Weslo

Weslo CADENCE 880 Bedienungsanleitung

Weslo

Weslo Cadence 830 Bedienungsanleitung

Weslo

Weslo Cadence 935 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence L 290 Bedienungsanleitung

Weslo

Weslo Cadence Ds23 Bedienungsanleitung

Weslo

Weslo WLTL19306.0 Bedienungsanleitung

Weslo

Weslo Cadence 500 Treadmill Bedienungs- und Wartungshandbuch

Weslo

Weslo Cadence Ds11 Bedienungsanleitung

Weslo

Weslo 78e 831.29522.0 Bedienungsanleitung

Weslo

Weslo Lyne 3500 Treadmill Bedienungs- und Wartungshandbuch

Weslo

Weslo CADENCE 1020 WETL28090 Bedienungsanleitung

Weslo

Weslo Cadence Sl 20 Bedienungsanleitung

Weslo

Weslo Lyne 3500 Treadmill Systemhandbuch

Weslo

Weslo Cadence A 40 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 10.0i Treadmill Bedienungsanleitung

Weslo

Weslo 925925 Bedienungsanleitung

Weslo

Weslo Lyne 3500 Treadmill Bedienungsanleitung

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung