Weslo Cadence 55 Bedienungsanleitung

USER'S MANUAL

Serial Number

Decal

Model No. WETL13606.0

Serial No.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing or damaged parts,

please call:

or write:

ICON Health & Fitness, Ltd.

Customer Service Department

Unit 4

Revie Road Industrial Estate

Revie Road

Beeston

Leeds, LS118JG

email: [email protected]

08457 089 009

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: A PART IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART LIST are attached in the

center of this manual.

WESLO is a registered trademark of ICON IP, Inc.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the

following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Place the treadmill on a level surface, with at

least 2.5 m (8 ft.) of clearance behind it and

0.5 m (2 ft.) on each side. Do not place the

treadmill on a surface that blocks any air

openings. To protect the floor or carpet from

damage, place a mat under the treadmill.

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should be used only by persons

weighing 115 kg (250 lbs.) or less.

8. Never allow more than one person on the

treadmill at a time.

9. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes

that could become caught in the treadmill.

Athletic support clothes are recommended for

both men and women.

Always wear athletic

shoes; never use the treadmill with bare feet,

wearing only stockings, or in sandals.

10. When connecting the power cord (see page

10), plug the power cord into an earthed cir-

cuit. No other appliance should be on the

same circuit. When replacing the fuse, an

ASTA approved BS1362 type should be fitted

to the fuse carrier. A 13 amp fuse should be

used.

11. If an extension cord is needed, use only a 3-

conductor, 1mm2(14-gauge) cord that is no

longer than 1.5 m (5 ft.).

12. Keep the power cord away from heated sur-

faces.

13. Never move the walking belt while the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See MAIN-

TENANCE AND TROUBLESHOOTING on page

17 if the treadmill is not working properly.)

14. Read, understand, and test the emergency

stop procedure before using the treadmill (see

OPERATION AND ADJUSTMENT on page 10).

15. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the

handrails while using the treadmill.

16. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid

sudden jumps in speed.

17. Never leave the treadmill unattended while it is

running. Always remove the key and unplug

the power cord when the treadmill is not in use.

18. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 6, and HOW TO FOLD

AND MOVE THE TREADMILL on page 15.)

You must be able to safely lift 20 kg (45 lbs.) to

raise, lower, or move the treadmill.

19. When folding or moving the treadmill, make

sure that the frame is securely held by the

latch pin.

20. Do not change the incline of the treadmill by

placing objects under the treadmill.

The decal shown at the right has been placed on the

treadmill. If the decal is missing, or if it is not legible,

call the toll-free telephone number on the front cover of

this manual and order a free replacement decal. Apply

the decal in the location shown. Note: The decal is not

shown at actual size.

21. Inspect and properly tighten all parts of the

treadmill regularly.

22. Never drop or insert any object into any

opening.

23. DANGER: Always unplug the power

cord immediately after use, before cleaning

the treadmill, and before performing the main-

tenance and adjustment procedures de-

scribed in this manual. Never remove the

motor hood unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorized service

representative only.

24. This treadmill is intended for in-home use

only. Do not use this treadmill in any commer-

cial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

Thank you for selecting the new WESLO®CADENCE

55 treadmill. The CADENCE 55 treadmill combines ad-

vanced technology with innovative design to make

your workouts at home more effective and enjoyable.

And when you’re not exercising, the CADENCE 55

treadmill can be folded up, requiring less than half the

floor space of other treadmills.

For your benefit, read this manual carefully before

using the treadmill.If you have questions after read-

ing this manual, please see the front cover of this man-

ual. To help us assist you, please note the product

model number and serial number before contacting us.

The model number of the treadmill is WETL13606.0.

The serial number can be found on a decal attached to

the treadmill (see the front cover of this manual for the

location).

Before reading further, please familiarise yourself with

the parts that are labelled in the drawing below.

BEFORE YOU BEGIN

Handrail

Storage Latch

Console

Key/Clip

Circuit Breaker

Incline Leg/Pin

Walking Belt

Hood

Wheel

Foot Rail

Rear Roller

Adjustment Bolts

Water Bottle Holder

(Bottle not included)

RIGHT SIDE

On/Off Switch

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; donot

dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking

belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to

the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant

on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the hex key and your own phillips screwdriver , two

spanners , and wire cutters .

Note: To identify small parts used during assembly, see the PART IDENTIFICATION CHART in the center of

this manual. Some parts may be preassembled.

1. Have a second person hold the Base (54) in the position

shown.

Identify the Left Upright (55) (the Right Upright [56] has a

large hole near the lower end).

Hold the Left Upright (55) so the bend is in the posi-

tion shown. Insert two Upright Bolts (2) into the

bracket on the Left Upright. Attach the Left Upright to

the Base (54) with the Upright Bolts and two Upright Nuts

(16). Do not tighten the Upright Nuts yet.

Attach the Right Upright (56) to the Base (54) in the same

way.

2. Slide the two Wheel Housings (64) onto the Base (54).

Attach each Wheel Housing with two Wheel Housing Bolts

(6), two Wheel Housing Washers (11), and two Wheel

Housing Nuts (15).

216

Large

Hole

611

64 15

Bend

3. With the help of a second person, raise the Uprights

(55, 56) so the Base (54) is flat on the floor as shown.

Position the front of the treadmill Frame (53) between the

Uprights (55, 56) as shown. Next, locate the long wire in-

side of the lower end of the Right Upright (see the inset

drawing). Secure the end of the wire to the end of the

Wire Harness (97) using the included plastic tie. Then,

pull the other end of the wire until the end of the Wire

Harness is extending from the indicated hole in the upper

end of the Right Upright.

Have a second person lift and hold the front end of the

Frame (53). Hold a Frame Spacer (111) between the Right

Upright (56) and the Frame. Attach the Right Upright and

the Frame Spacer to the Frame with a Frame Bolt (1), a

Frame Washer (14), and a Frame Star Washer (9).

Repeat this step on the left side of the treadmill. 9

111

Large

Hole

4. Have a second person raise and hold the treadmill

Frame (not shown).

Identify the Gas Spring (101). Note that the Gas Spring

has a cylinder end and a piston end. See the two small

inset drawings. Locate the Spring Clip (52) in the cylinder

end of the Gas Spring. Using your fingernail or the end of

ascrewdriver, press on the end of the Spring Clip to

loosen it, rotate the Spring Clip, and then pull the Spring

Clip out of the Gas Spring. Be careful to avoid losing

the Spring Clip. Note: Extra Spring Clips are included.

Next, hold the cylinder end of the Gas Spring (101) near

the bracket in the center of the Base (54). Press the end

of the Gas Spring as far as possible onto the ball on the

bracket.

See drawing 4a. Insert the Spring Clip (52) into the two

indicated small holes in the end of the Gas Spring (101).

Then, rotate the Spring Clip until it clips onto the Gas

Spring.

101

Holes

Bracket

Cylinder

Piston

Bracket

97 56

Tie

Wire

7. Hold the Console Assembly (90) near the Right Upright

(56). Touch the Right Handrail to discharge any static.

Insert the end of the Wire Harness (97) into the hole in

the bottom of the Right Handrail (57) and out of the large

hole in the side. Next, Insert the end of the Wire Harness

through the two looped plastic ties.

Press the end of the Wire Harness (97) into the indicated

connector on the back of the Console Assembly (90).

The end of the Wire Harness should slide easily into

the connector and snap into place. If it does not,turn

the end of the Wire Harness and try again. IF THE CON-

NECTOR IS NOT INSERTED PROPERLY, THE CON-

SOLE MAY BE DAMAGED WHEN THE POWER IS

TURNED ON.

Plastic

Ties

Connector

6. Turn the Console Assembly (90) face-down. Be careful

not to scratch the face of the Console Assembly.

Identify the Right Handrail (57), which has a large hole in

one side.

Attach the Right Handrail (57) to the Console Assembly

(90) with two Console Screws (4), a Crossbar Screw (5),

and a Crossbar Star Washer (12).

Attach the Left Handrail (not shown) in the same way.

Large Hole

5. Pivot the piston end of the Gas Spring (101) up to the

position shown. Remove the Spring Clip (52) from the

piston end of the Gas Spring.

Next, align with piston end of the Gas Spring (101) with

the bracket in the center of the Frame (53). Press the

end of the Gas Spring onto the ball on the bracket. Note:

It may be necessary to pivot the Frame forward or back-

ward slightly to align the end of the Gas Spring with the

ball.

See drawing 5a. Insert the Spring Clip (52) into the two

indicated small holes in the Gas Spring (101). Then, ro-

tate the Spring Clip until it clips onto the Gas Spring.

With the help of a second person, lower the Frame (53) to

the floor.

101

Bracket

10. Carefully lower the Handrails (57, 58) to the floor. Center

the Frame (53) between the Handrails, and tighten the

four Upright Bolts (2). Then, raise the Handrails back to

the vertical position.

See drawing 10a. Attach the Latch Assembly (108) to the

Left Upright (55) with two Latch Screws (7). Make sure

that the Latch Assembly is oriented as shown.

See HOW TO CHANGE THE INCLINE OF THE TREAD-

MILL on page 14.Adjust the incline of the treadmill as

desired.

11. Make sure that all parts are properly tightened be-

fore you use the treadmill. Note: Extra hardware may

be included. Keep the included hex keys in a secure

place; the large hex key is used to adjust the walking

belt (see page 18). To protect the floor or carpet, place

amat under the treadmill.

108

9. Set the Console Assembly (90) on the Right Upright (56)

and the Left Upright (not shown). Next, start four

Handrail Bolts (3) with four Handrail Washers (13) and

four Handrail Star Washers (10) (only two of each are

shown) into the Right Upright and the Left Upright.

Then, tighten all four Handrail Bolts.

Insert the slack in the Wire Harness (97) down into the

Right Upright (56).

Attach the Console Back (92) to the Console Assembly

(90) with four Console Back Screws (7). Make sure that

the Wire Harness (97) is in the indicated slot in the

Console Back and that no wires are pinched.

Slot

10a

57, 58

53 2

8. Insert the slack in the Wire Harness (97) down into the

Right Upright (56). Then, tighten the two plastic ties

around the Wire Harness, and cut off the ends of the plas-

tic ties.

97 Plastic

Ties

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply sili-

cone spray or other substances to the walking belt or the walking platform. Such substances will deterio-

rate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

This product must be earthed. If it should malfunction or break

down, earthing provides a path of least resistance for electric cur-

rent to reduce the risk of electric shock. This product is equipped

with a power cord having an equipment-earthing conductor and an

earthing plug. Important: If the power cord is damaged, it must

be replaced with a manufacturer-recommended power cord.

See drawing 1. Plug the indicated end of the power cord into the

socket on the treadmill.

See drawing 2. Press the pins on the power cord into the metal clips

in the adapter as shown. Close the adapter cover over the end of the

power cord and tighten the screw in the adapter. Important: Make

sure that the adapter cover is secure and the screw has been

tightened before using the power cord.

See drawing 3. Plug the power cord into an appropriate outlet that is

properly installed and earthed in accordance with all local codes and

ordinances. Important: The treadmill is not compatible with

GFCI-equipped outlets.

DANGER: Improper connection of the equipment-earthing conductor can result in an in-

creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as

to whether the product is properly earthed. Do not modify the plug provided with the product—if it will

not fit the outlet, have a proper outlet installed by a qualified electrician.

Socket on treadmill

Metal

Clips

Pins

Screw

Adapter

Outlet

Adapter

Cover

OPERATION AND ADJUSTMENT

Andere Handbücher für Cadence 55

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weslo Tretmühle Handbücher

Weslo

Weslo Cadence 80 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 16.0 Cwl Treadmill Einrichtungshandbuch

Weslo

Weslo Cadence 830 Bedienungsanleitung

Weslo

Weslo Cadence G 5.9 Treadmill Bedienungsanleitung

Weslo

Weslo WLTL11093 Bedienungsanleitung

Weslo

Weslo WLTL01530 Bedienungsanleitung

Weslo

Weslo Cadence 1050 Benutzerhandbuch

Weslo

Weslo Cadence 78s Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 215s Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 3280 Bedienungsanleitung

Weslo

Weslo CROSSWALK 5.2T Bedienungsanleitung

Weslo

Weslo CardioStride 3.0 Bedienungsanleitung

Weslo

Weslo Cadence 4.9 Ery Treadmill Bedienungsanleitung

Weslo

Weslo Cadence M6 Elliptical null

Weslo

Weslo Cadence Ls10 Bedienungsanleitung

Weslo

Weslo CADENCE 850 WETL85061 Bedienungsanleitung

Weslo

Weslo 445i Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 4.0 Bedienungsanleitung

Weslo

Weslo WLTL29200 Bedienungsanleitung

Weslo

Weslo Cadence 1050 Kurzanleitung

Weslo

Weslo Cadence 75 Treadmill Kurzanleitung

Weslo

Weslo Cadence 935 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 630 Benutzerhandbuch

Weslo

Weslo Cadence 50 Se Treadmill Bedienungsanleitung

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung