Weslo Cadence J2.8 Treadmill Bedienungsanleitung

USER'S MANUAL

Serial Number Decal

Model No. WCTL19108.0

Serial No.

QUEST ONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. f you

have questions, or if parts are

damaged or missing, PLEASE

CONTACT OUR CUSTOMER

SERV CE DEPARTMENT

D RECTLY.

CALL TOLL-FREE:

1-888-936-4266

Mon.–Fri., 8:00 until 17:00 EST

(excluding holidays)

OR E-MA L US:

customerservice@iconcanada.ca

CAUT ON

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

Visit our website at

www.weslo.com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

MPORTANTPRECAUTONS .................................................................2

BEFOREYOUBEGN .......................................................................4

ASSEMBLY ...............................................................................5

OPERATONANDADJUSTMENT .............................................................8

HOWTOFOLDANDMOVETHETREADMLL ..................................................11

MANTENANCEANDTROUBLESHOOTNG ....................................................12

CONDTONNGGUDELNES ...............................................................14

ORDERNGREPLACEMENTPARTS ..................................................BackCover

LMTEDWARRANTY...............................................................BackCover

Note: A PART DENT F CAT ON CHART, an EXPLODED DRAW NG, and a PART L ST are attached in the

center of this manual.

1. t is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Place the treadmill on a level surface, with at

least 8 ft. (2.4 m) of clearance behind it and 2

ft. (0.6 m) on each side. Do not place the

treadmill on any surface that blocks air open-

ings. To protect the floor or carpet from dam-

age, place a mat under the treadmill.

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should not be used by persons

weighing more than 250 lbs. (113 kg).

8. Never allow more than one person on the

treadmill at a time.

9. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes

that could become caught in the treadmill.

Athletic support clothes are recommended for

both men and women. Always wear athletic

shoes. Never use the treadmill with bare feet,

wearing only stockings, or in sandals.

10. When connecting the power cord (see page 8),

plug the power cord into a surge suppressor

(not included) and plug the surge suppressor

into a grounded circuit capable of carrying 15

or more amps. No other appliance should be on

the same circuit. Do not use an extension cord.

11. Use only a single-outlet surge suppressor that

meets all of the specifications described on

page 8.

12. Failure to use a properly functioning surge

suppressor could result in damage to the con-

trol system of the treadmill. f the control sys-

tem is damaged, the walking belt may change

speed, accelerate, or stop unexpectedly,

which may result in a fall and serious injury.

13. Keep the power cord and the surge suppres-

sor away from heated surfaces.

14. Never move the walking belt while the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See

BEFORE YOU BEG N on page 4 if the tread-

mill is not working properly.)

15. Read, understand, and test the emergency

stop procedure before using the treadmill (see

STEP-BY-STEP CONSOLE OPERAT ON on

page 9).

WARN NG: To reduce the risk of burns, fire, electric shock, or injury to persons, read the

following important precautions and information before operating the treadmill.

MPORTANT PRECAUT ONS

The decals shown here have been ap-

plied in the locations shown. f a decal is

missing or illegible, call the telephone

number on the front cover of this

manual and request a free replace-

ment decal. Apply the decal in the lo-

cation shown. Note: The decals may

not be shown at actual size.

•Tension Dangereuse

• Risque de Choc Électrique

•Débranchez le tapis roulant Avant

l’Assemblage/Désassemblage

•Hazardous Voltage

• Risk of Electric Shock

•Unplug Treadmill before

Assembly/ Disassembly

ATTENTION

16. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the

handrails while using the treadmill.

17. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid

sudden jumps in speed.

18. Never leave the treadmill unattended while it

is running. Always remove the key, unplug

the power cord, and switch the reset/off cir-

cuit breaker to the off position when the

treadmill is not in use. (See the drawing on

page 5 for the location of the circuit breaker.)

19. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 5 and HOW TO FOLD

AND MOVE THE TREADM LL on page 11.)

You must be able to safely lift 45 lbs. (20 kg)

to raise, lower, or move the treadmill.

20. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

21. Do not change the incline of the treadmill by

placing objects under the treadmill.

22. nspect and properly tighten all parts of the

treadmill regularly.

23. Never drop or insert any object into any

opening on the treadmill.

24. DANGER: Always unplug the power

cord immediately after use, before cleaning

the treadmill, and before performing the main-

tenance and adjustment procedures de-

scribed in this manual. Never remove the

motor hood unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorized service

representative only.

25. This treadmill is intended for in-home use

only. Do not use this treadmill in any commer-

cial, rental, or institutional setting.

WARN NG: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. CON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

SAVE THESE NSTRUCT ONS

Thank you for selecting the WESLO®CADENCE J 2.8

treadmill. The CADENCE J 2.8 treadmill combines ad-

vanced technology with innovative design to let you

enjoy an excellent form of cardiovascular exercise in

the convenience and privacy of your home. And when

youʼre not exercising, the unique CADENCE J 2.8 can

be folded up, requiring less than half the floor space of

other treadmills.

For your benefit, read this manual carefully before

using the treadmill. f you have questions after read-

ing this manual, please see the front cover of this man-

ual. To help us assist you, note the product model

number and serial number before contacting us. The

model number and the location of the serial number

decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

BEFORE YOU BEG N

Handrail

Console

Key/Clip

Reset/Off

Circuit Breaker

ncline Leg

Walking Belt

Hood

Wheel

Foot Pad

Power Cord

Rear Roller

Adjustment Bolts

Water Bottle Holder

(Bottle not included)

R GHT S DE

LEFT S DE

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not

dispose of the packing materials until assembly is completed. Do not remove the long plastic tape inside the

Right Handrail until told to. Note: The underside of the treadmill walking belt is coated with high-performance lu-

bricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the ship-

ping carton. This does not affect treadmill performance. f there is lubricant on top of the walking belt, simply wipe

off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included allen wrench and your own phillips screwdriver ,

adjustable wrenches , and 9/16” socket wrench , wire cutters .

Note: To identify small parts used during assembly, see the PART DENT F CAT ON CHART in the center of

this manual.

1. Hold the Base (71) in

the position shown.

dentify the Right

Handrail (6), which has

a large hole near the

lower end. Hold the

Right Handrail with

the bend in the posi-

tion shown.

Using a 9/16” socket wrench and the included allen

wrench, attach the Right Handrail (6) to the Base (71) with

two Handrail Bolts (12), two Formed Washers (31), and

two Nuts (17). Do not tighten the Handrail Nuts yet.

Attach the Left Handrail (7) to the Base (71) in the

same way.

Large

Hole

Bend

•Tension Dangereuse

•Risque de Choc Électrique

•Débranchez le tapis roulant Avant

l’Assemblage/Désassemblage

•Hazardous Voltage

•Risk of Electric Shock

• Unplug Treadmill before

Assembly/ Disassembly

ATTENTION

2. Position the treadmill near the Handrails (6, 7) as shown. A

long plastic tape is inside the Right Handrail (6). Secure

the end of the plastic tape to the Wire Harness (22) with

the included plastic tie. Pull on the other end of the tape

to pull the Wire Harness through the Right Handrail and

out of the top.

With the help of a second person, raise the Handrails (6,

7) so that the Base (71) is resting flat on the floor.

71 6

Tie

Tape

5. Hold the Console Base (1) near the Right Handrail (6).

Touch the Right Handrail to discharge any static.

nsert the end of the Wire Harness (22) through the three

looped plastic ties. Press the end of the Wire Harness into

the connector on the back of the Console Base (1) in the lo-

cation shown. The connectors should slide in easily and

snap into place. f it does not, turn the connector and then

try again. F THE CONNECTORS ARE NOT CON-

NECTED PROPERLY, THE CONSOLE MAY BE DAM-

AGED WHEN THE POWER S TURNED ON.

Plastic

Ties

Connector

4. Have a second person raise and hold the front end of the

treadmill. Hold a Frame Spacer (13) between the Right

Handrail (6) and the Frame (55). Attach the Right Handrail

and the Base (71) to the Frame with a Frame Bolt (10), a

Handrail Washer (11), and a Star Washer (33).

Repeat this step on the left side of the treadmill.

3. Using two adjustable wrenches, attach the Wheels (15)

to the outer sides of the Base (71) with two Wheel Bolts

(14) and two Nuts (40) as shown. Do not overtighten

the Wheel Nuts; the Wheels should turn freely.

t may be helpful to tip the Handrails (6, 7) forward when

attaching the Wheels (15).

9. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen

wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the

floor or carpet, place a mat under the treadmill.

8. Have a second person raise the Frame to the vertical po-

sition (55). Make sure that the Latch Pin (69) is in the

Storage Latch (41) as shown. Attach the Storage Latch to

the Frame (55) with three Latch Screws (73). Do not

tighten the Screws yet.

See the inset drawing. Position the Storage Latch (69) so

the Latch Pin (69) is aligned with the hole in the Left

Handrail (7). Slide the Latch Pin into the hole, as shown.

Tighten the three Latch Screws (73).

Lower the Frame (55). (See HOW TO LOWER THE

TREADM LL FOR USE on page 11.)

73 41

Hole

7. Attach the Console Back (4) to the Console (1) with four

Console Back Screws (58). Make sure that no wires are

pinched.

See step 1. Tighten the four Nuts (17).

6. Set the Console (1) on the Right Handrail (6) and the Left

Handrail (not shown). Start four Console Screws (70)

(only two are shown) into the Console. After you have

started all four Console Screws, tighten them.

nsert the excess Wire Harness (22) down into the Right

Handrail (6). Tighten the three plastic ties around the Wire

Harness, and then cut off the ends of the plastic ties.

Plastic

Ties

OPERAT ON AND ADJUSTMENT

THE PRE-LUBR CATED WALK NG BELT

Your treadmill features a walking belt coated with high-

performance lubricant. MPORTANT: Never apply sil-

icone spray or other substances to the walking

belt or the walking platform. Such substances will

deteriorate the walking belt and cause excessive

wear.

HOW TO PLUG N THE POWER CORD

Your treadmill, like any other type of sophisticated

electronic equipment, can be seriously damaged by

sudden voltage changes in your homeʼs power.

Voltage surges, spikes, and noise interference can

result from weather conditions or from other appli-

ances being turned on or off. To decrease the possi-

bility of your treadmill being damaged, always use

a surge suppressor with your treadmill (see draw-

ing 1 at the right).

Use only a single-outlet surge suppressor that is

UL 1449 listed as a transient voltage surge sup-

pressor (TVSS). The surge suppressor must have a

UL suppressed voltage rating of 400 volts or less

and a minimum surge dissipation of 450 joules.

The surge suppressor must be electrically rated for

120 volts AC and 15 amps. There must be a moni-

toring light on the surge suppressor to indicate

whether it is functioning properly. Failure to use a

properly functioning surge suppressor could result

in damage to the control system of the treadmill. f

the control system is damaged, the walking belt

may change speed, accelerate or stop unexpect-

edly, which may result in a fall and serious injury.

This product must be grounded. f it should malfunc-

tion or break down, grounding provides a path of least

resistance for electric current to reduce the risk of elec-

tric shock. This product is equipped with a cord having

an equipment-grounding conductor and a grounding

plug. Plug the power cord into a surge suppressor,

and plug the surge suppressor into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

mportant: The treadmill is not compatible with

GFC -equipped outlets.

This product is for use on a nominal 120-volt circuit,

and has a grounding plug that looks like the plug illus-

trated in drawing 1 below. A temporary adapter that

looks like the adapter illustrated in drawing 2 may be

used to connect the surge suppressor to a 2-pole

receptacle as shown in drawing 2 if a properly

grounded outlet is not available.

The temporary adapter should be used only until a

properly grounded outlet (drawing 1) can be installed

by a qualified electrician.

The green-colored rigid ear, lug, or the like extending

from the adapter must be connected to a permanent

ground such as a properly grounded outlet box cover.

Whenever the adapter is used it must be held in place

by a metal screw. Some 2-pole receptacle outlet box

covers are not grounded. Contact a qualified elec-

trician to determine if the outlet box cover is

grounded before using an adapter.

DANGER: mproper connection

of the equipment-grounding conductor can

result in an increased risk of electric shock.

Check with a qualified electrician or service-

man if you are in doubt as to whether the

product is properly grounded. Do not modify

the plug provided with the product—if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician.

Grounded Outlet Box

Grounding Plug

Surge Suppressor

Grounding Pin

Adapter

Lug

Metal Screw

Grounded Outlet

Grounding Pin

D AGRAM OF THE CONSOLE

Clip

Key

Note: f there is a sheet of clear plastic

on the console, remove the plastic.

STEP-BY-STEP CONSOLE OPERAT ON

Before operating the console, make sure that the

power cord is properly plugged in (see page 8).

n addition, locate the reset/off

circuit breaker on the treadmill

near the power cord, and

make sure that the circuit

breaker is in the reset posi-

tion.

Next, stand on the foot rails of the treadmill. Find the

clip attached to the key (see the drawing above), and

slide the clip onto the waistband of your clothes. Then,

insert the key fully into the console. After a moment,

the display will light. mportant: n an emergency sit-

uation, the key can be pulled from the console,

causing the walking belt to slow to a stop. Test the

clip by carefully taking a few steps backward; if the

key is not pulled from the console, adjust the posi-

tion of the clip.

Follow the steps below to operate the console.

nsert the key fully into the console.

A moment after the key is inserted, the display will

light.

Press the Digital Speed increase button to start

the walking belt.

A moment after the button is pressed, the walking

belt will begin to move at 1 mph. Hold the handrails

and begin walking.

As you exercise, change the speed of the walking

belt as desired by pressing the Digital Speed but-

tons. Each time a button is pressed, the speed

setting will change by 0.1 mph; if a button is held

down, the speed setting will change in increments

of 0.5 mph.

CAUT ON: Before operating the

console, read the following precautions.

• Do not stand on the walking belt when turn-

ing on the power.

• Always wear the clip (see the drawing

above) while operating the treadmill.

• Adjust the speed in small increments to

avoid sudden jumps in speed.

• To reduce the possibility of electric shock,

keep the console dry. Avoid spilling liquids

on the console and place only a sealed

water bottle in the water bottle holders.

Reset

To stop the walking belt, press the Stop button.

Note: f the time mode is displayed (see step 3

below), the time will begin to flash.

Note: The first time the treadmill is used, observe

the alignment of the walking belt, and center the

walking belt if necessary (see page 13).

Follow your progress with the display.

As you exercise, the console can display the fol-

lowing modes:

• Time—This

mode displays

the elapsed

time. Note: f the

time is displayed

when the walk-

ing belt is

stopped, the

time will begin to flash.

• Distance—This mode displays the distance that

you have walked or run, in miles.

• Speed—This mode displays the speed of the

walking belt, in miles per hour.

• Calories—This mode displays the approximate

number of calories you have burned during your

workout.

• Fat Calories (FAT)—This mode displays the ap-

proximate number of fat calories you have

burned (see FAT BURN NG on page 14).

• Scan—This mode displays the Time, Distance,

Speed, Calories, and Fat Calories modes, for

about seven seconds each, in a repeating cycle.

When the key is

inserted, the Scan

mode will be se-

lected. One mode

indicator will ap-

pear below the

word SCAN, and

a second mode

indicator will show

which mode is

currently displayed.

To select only the Time, Distance, Speed,

Calories, or Fat Calories mode, press the Mode

button repeatedly until a mode indicator appears

above or below

the word T ME,

D STANCE,

SPEED, CALO-

R ES, or FAT.

Make sure that

there is not a

mode indicator

below the word

SCAN.

To reset all modes, press the Stop button, remove

the key, and then reinsert the key.

When you are finished exercising, remove the

key from the console.

Step onto the foot rails, press the Stop button, and

remove the key from the console. Keep the key in a

secure place. Then, switch the reset/off circuit

breaker to the “off” position and unplug the power

cord.

HOW TO CHANGE THE NCL NE OF THE TREADM LL

To vary the intensity of your exercise, the incline of the

treadmill can be changed. There are two incline levels.

Before changing the incline, remove the key and

unplug the power cord. Next, fold the treadmill to the

storage position (see page 11).

To change

the incline, re-

move the in-

cline pin from

one of the in-

cline legs as

shown. Adjust

the incline leg

to the desired

height, and

fully reinsert

the incline

pin. Make

sure that the incline pin is in the “locked” position

shown in the inset drawing. Adjust the other incline leg

in the same way. CAUT ON: Before using the tread-

mill, make sure that both incline legs are at the

same height and that both incline pins are fully in-

serted from the direction shown. Do not use the

treadmill with the incline pins removed.

After you have adjusted the incline legs, lower the

treadmill (see page 11).

Mode ndicator

ncline

Mode ndicator

Andere Handbücher für Cadence J2.8 Treadmill

Dieses Handbuch passt für folgende Modelle

Andere Weslo Tretmühle Handbücher

Weslo

Weslo Cadence C 8 Treadmill Kurzanleitung

Weslo

Weslo Cadence S 8 Benutzerhandbuch

Weslo

Weslo Cadence 955 Bedienungsanleitung

Weslo

Weslo Easy compact 2 treadmill Referenzhandbuch

Weslo

Weslo Cadence A 40 Treadmill Bedienungsanleitung

Weslo

Weslo WLTL26080 Bedienungsanleitung

Weslo

Weslo Cadence G 7.0 WLTL39810.0 Bedienungsanleitung

Weslo

Weslo WLTL19010 Bedienungsanleitung

Weslo

Weslo Cadence 10.0 P.i. Bedienungsanleitung

Weslo

Weslo Cadence S6 Treadmill Kurzanleitung

Weslo

Weslo CADENCE TS 310 Bedienungsanleitung

Weslo

Weslo WLTL29321 Bedienungsanleitung

Weslo

Weslo Easy compact 2 treadmill Systemhandbuch

Weslo

Weslo Cadence 70 Treadmill Bedienungsanleitung

Weslo

Weslo WETL59710.0 Bedienungsanleitung

Weslo

Weslo Cadence 875 Bedienungsanleitung

Weslo

Weslo Cadence R 5.2 Treadmill Benutzerhandbuch

Weslo

Weslo WCTL39102 Bedienungsanleitung

Weslo

Weslo Cadence Ds11 Bedienungsanleitung

Weslo

Weslo Cadence 16.0 Cwl Treadmill Bedienungsanleitung

Weslo

Weslo Crosswalk 5.0t Bedienungsanleitung

Weslo

Weslo WETL49710.2 Bedienungsanleitung

Weslo

Weslo Cadence 3280 Bedienungsanleitung

Weslo

Weslo Crosswalk 5.0t Treadmill Benutzerhandbuch

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung