Accu-Scope EXS-210 Bedienungsanleitung

MANUAL

73 Mall Drive, Commack, NY 11725 • 631-864-1000 (P) • 631-543-8900 (F)

www.accu-scope.com • [email protected]

EXS-210

STEREO

MICROSCOPE SERIES

EXS-210 STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 1

CONTENTS

SAFETY NOTES ..................................................................................................................2

CARE AND MAINTENANCE................................................................................................2

INTRODUCTION..................................................................................................................3

UNPACKING AND COMPONENTS.....................................................................................3

COMPONENTS DIAGRAM ...............................................................................................3-4

ASSEMBLY..........................................................................................................................5

ADJUSMENT AND OPERATION

CONNECTING THE POWER CORD..............................................................................5

ADJUSTING INTERPUPILLARY DISTANCE..................................................................5

ADJUSTING THE DIOPTER...........................................................................................6

ADJUSTING THE FOCUSING TENSION.......................................................................6

CHANGING THE MAGNIFICATION ...............................................................................7

ADJUSTING ILLUMINATION..........................................................................................7

OBSERVING A SPECIMEN............................................................................................8

RECHARGING THE MICROSCOPE ..............................................................................8

REPLACING THE BATTERIES.......................................................................................9

REPLACING THE LED BULBS.......................................................................................9

SPECIFICATIONS..............................................................................................................10

TROUBLESHOOTING........................................................................................................11

MAINTENANCE..................................................................................................................12

SERVICE............................................................................................................................12

WARRANTY.......................................................................................................................12

EXS-210 STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 2

SAFETY NOTES

1. Open the shipping carton carefully to prevent any accessory, i.e. eyepieces, from dropping and being

damaged.

2. Keep the instrument out of direct sunlight, high temperature or humidity, and dusty environments.

3. If any specimen solutions or other liquids splash onto the stage, objective or any other component,

disconnect the power cord immediately and wipe up the spillage. Otherwise, the instrument may be

damaged.

4. LAMP REPLACEMENT -- CAUTION: the glass housing of the lamp may be extremely

hot. DO NOT attempt to change the lamp before it is completely cooled or without

wearing adequate skin protection.

5. All electrical connectors (power cord) should be inserted into an electrical surge protector to prevent

damage due to voltage fluctuations.

6. Confirm that the input voltage indicated on your microscope corresponds to your line voltage. The

use of a different input voltage other than indicated will cause severe damage to the microscope.

NOTE: Always plug the microscope power cord into a suitable grounded electrical outlet.

Use only the AC adapter provided with the microscope.

CARE AND MAINTENANCE

1. Do not attempt to disassemble any component including eyepieces, objective housing or the focusing

assembly.

2. Keep the instrument clean; remove dirt and debris regularly. Accumulated dirt on metal surfaces

should be cleaned with a damp cloth. More persistent dirt should be removed using a mild soap

solution. Do not use organic solvents for cleansing.

3. The outer surface of the optics should be inspected and cleaned periodically using an air bulb. If dirt

remains on the optical surface, use a soft, lint free cloth or cotton swab dampened with a lens

cleaning solution (available at camera stores). All optical lenses should be swabbed using a circular

motion. A small amount of absorbent cotton wound on the end of a tapered stick makes a useful tool

for cleaning recessed optical surfaces. Avoid using an excessive amount of solvents as this may

cause problems with optical coatings or cemented optics or the flowing solvent may pick up grease

making cleaning more difficult.

4. Store the instrument in a cool, dry environment. Cover the microscope with the dust cover when not

in use.

5. ACCU-SCOPE®microscopes are precision instruments which require periodic servicing to maintain

proper performance and to compensate for normal wear. A regular schedule of preventative

maintenance by qualified service personnel is highly recommended. Your authorized ACCU-SCOPE®

distributor can arrange for this service.

EXS-210 STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 3

INTRODUCTION

Congratulations on the purchase of your new ACCU-SCOPE®stereo microscope. ACCU-SCOPE®

microscopes are engineered and manufactured to the highest quality standards. Your microscope will

last a lifetime if used and maintained properly. ACCU-SCOPE®microscopes are carefully assembled,

inspected and tested by our staff of trained technicians in our New York facility. Careful quality control

procedures ensure each microscope is of the highest quality prior to shipment.

UNPACKING AND COMPONENTS

Your microscope arrived packed in a molded shipping carton. Do not discard the carton: the shipping

carton should be retained for reshipment of your microscope if needed. Avoid placing the microscope in

dusty surroundings or in high temperature or humid areas as mold and mildew can form. Carefully

remove the microscope from the shipping carton and place the microscope on a flat, vibration-free

surface.

COMPONENTS DIAGRAM

Eyepieces

Rotatable Objective

Housing/

Magnification Turret

Stage Plate

Base

Frame

Focus

Adjustment

Knob

ON/OFF

Switch

Transmitted (Bottom)

Illuminator

Variable Intensity

Adjustment Dial

Stage Clips

Carry Handle

Eyepiece

Tubes

Diopter

Adjustment Collar

EXS-210 STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 4

COMPONENTS DIAGRAM (continued)

Indicent (Top) Illuminator

Transmitted (Bottom)

Illuminator

Incident (Top)

Illuminator

Variable Intensity

Adjustment Dial

Power Cord

Receptacle

EXS-210 STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 5

ASSEMBLY

Your stereo microscope comes pre-assembled. Optional eyeguards are included with your microscope

and can be installed on the eyepieces to help block out extraneous light.

ADJUSTMENT & OPERTATION

Voltage Check

Confirm that the input voltage indicated on the rear label of the

microscope corresponds to your line voltage. The use of a

different input voltage than indicated will cause severe damage

to your microscope.

Connecting the Power Cord (Fig. 1)

Make sure the ON/OFF (I/O) switch ①is turned to the OFF (O)

position. With the microscope facing away from you, make sure

the illuminators are turned off.

To turn the illuminators off: for the bottom illuminator –the dial

on the left side of the microscope ②should be turned all the

way toward the front of the microscope (or away from you); for

the Top illuminator –the dial on the right side ③of the

microscope should be turned all the way toward the back of the

microscope (or toward you).

Insert the power cord into the power receptacle on the back of

the microscope ④; make sure the connection is snug.

Plug the other end of the power cord into the power supply

receptacle.

Input: 100V～240V, 0.15A; 50/60Hz

Output: 4.5V DC; 1000mA

Adjusting Interpupillary Distance (Fig. 2)

Different users have different interpupillary distances (this

distance is between the centers of pupils of each eye). When

operators of the microscope change, it will be necessary to

adjust interpupillary distance.

While looking through the eyepieces, hold the left and right

eyepiece tubes ① of the binocular assembly and adjust the

eyepiece tubes by opening or closing them until the left and right

fields of view coincide completely and you are able to see a

complete circle.

Fig. 1

①

③

②

④

Fig. 2

①

EXS-210 STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 6

ADJUSTMENT & OPERATION (continued)

Adjusting Diopter Ring (Fig. 3)

Place an easy-to-observe specimen on the stage plate, i.e., a

coin.

Rotate the magnification turret ① to the highest magnification,

then turn the focusing knob ②to focus the specimen.

Rotate the magnification turret ① to the lowest magnification,

looking only into the left eyepiece, adjust the diopter ring ③on

left eyepiece to focus the specimen.

NOTE: The working distance of the microscope is 57mm (the

distance between the microscope objective to the top of the

specimen).

Adjusting the Focusing Tension (Fig. 4)

To adjust the tension, hold both left and right focus adjustment

knobs ①with both hands, hold the left knob (to prevent it from

turning), and rotate the right knob clockwise to increase

(tighten) or counterclockwise to decrease (loosen) the focus

knob tension.

After tension adjustment has been completed, always rotate

both adjustment knobs in the same direction.

①

Fig. 3

Fig. 4

①

②

③

EXS-210 STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 7

ADJUSTMENT & OPERATION (continued)

Changing the Magnification (Fig. 5)

Using the finger grips at the top of the turret ①, rotate the

objective turret until it clicks into place. The magnification of the

objective in the field of view is indicated by the number ②on

the front of the objective turret (facing forward).

Additional magnification ranges can be obtained through the

use of optional 5x, 15x, or 20x eyepieces.

Total Magnification = Magnification of microscope body x

magnification of eyepiece

(i.e., 3x X 10=30x)

Adjusting Illumination (Fig. 6)

The EXS-210 is equipped with a rechargeable variable, built-in

3-way illumination system: LEDs for incident (top) and

transmitted (bottom).

Brightness adjustment: the right brightness adjustment dial ①

is used to adjust the bottom illumination, and the left brightness

adjustment dial ②is used to adjust the top illumination.

Turn the dials to adjust the brightness as needed.

Each dial also has its own on/off so you can use either top

illuminator or bottom illuminator, or both illuminators

simultaneously.

For more information about the rechargeable LED illumination

system and replacing the rechargeable batteries, please refer to

pages 8-9.

①

Fig. 5

Fig. 6

②

①

②

EXS-210 STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 8

ADJUSTMENT & OPERATION (continued)

Observing a Specimen (Fig. 7)

Turn on the microscope.

Select the appropriate illuminator for the specimen being

observed; there are three modes of illumination:

Incident (top) –for viewing opaque specimens

Transmitted (bottom) –for viewing translucent specimens

Incident & Transmitted –to develop contrasting conditions on

a variety of specimens.

Place a specimen in the center of the stage plate area ①.

While looking through both eyepieces with both eyes, focus the

microscope at the highest power by turning the focus

adjustment knob(s) ②to bring the specimen into focus. This

will keep the specimen in close focus at any magnification. A

slight turn of the focusing knobs may be needed to sharpen

focus.

Recharging the Microscope (Fig. 8)

The LED cordless, rechargeable microscope is completely

portable and be used indoors or outdoors in any location where

there is no electrical outlet access.

The LED cordless microscope is powered by three 1.2v NiMH

AA 1300mAh (Nickel Metal Hydride) rechargeable batteries,

and when used properly can sustain approximately 2 hours

(depending on the light intensity/user) before a charge is

required.

Each microscope is supplied with its own 4.5v/1000A line

cord/charger and would require approximately 8 hours for a full

charge. The life expectancy of the rechargeable batteries is

approximately 10,000 hours or equivalent to 250 recharges

before needing replacement.

NOTE: Your microscope can be used while recharging.

Use ONLY the AC adapter/cord that came with your

microscope.

①

Fig. 7

②

Fig. 8

EXS-210 STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 9

ADJUSTMENT & OPERATION (continued)

IMPORTANT

USE ONLY 1.2v NiMH AA

1300mAh (Nickel Metal

Hydride) rechargeable

batteries in your microscope.

Using any other type of

battery may damage to your

microscope.

Replacing the Rechargeable Batteries (Fig. 9)

1. Unplug the microscope from the electrical outlet (if plugged in)

and unplug charger from rear of microscope (if plugged in).

2. Carefully place the microscope on the back of its arm so the

bottom of the microscope base is facing towards you.

3. Open the trap door on the bottom using a small Philips head

(+) screw driver.

4. Replace the three NiMH AA 1300mAh rechargeable batteries.

5. Close the trap door, and place the microscope in an upright

position.

6. Plug the charger to the power receptacle on the back of the

microscope and plug into an electrical receptacle for continued

use while charging.

Allow the LED microscope to charge for 8 hours before using as

cordless.

Replacing the LED Bulbs

The reflected (top) and transmitted (bottom) lights can be used

simultaneously. The lux rating for the reflected illuminator is

7000lux, and the transmitted 18,000 lux by a distance of 70mm.

The life expectancy of the LED bulbs is 20,000 hours. The LED

bulbs are covered by a 1 year manufacturer’s warranty.

Should your LED bulbs need replacing, please contact an

authorized ACCU-SCOPE service center or call ACCU-SCOPE

Inc.’s technical service department at 631-864-1000 for an

authorized service center near you.

Fig. 9

Inhaltsverzeichnis

Andere Accu-Scope Mikroskop Handbücher

Accu-Scope

Accu-Scope 3078-HD Bedienungsanleitung

Accu-Scope

Accu-Scope 3055 Bedienungsanleitung

Accu-Scope

Accu-Scope 3025-LCD Bedienungsanleitung

Accu-Scope

Accu-Scope 3012-LED Bedienungsanleitung

Accu-Scope

Accu-Scope 3078 Series Bedienungsanleitung

Accu-Scope

Accu-Scope EXC-500 Bedienungsanleitung

Accu-Scope

Accu-Scope EXC-350 Series Bedienungsanleitung

Accu-Scope

Accu-Scope 3075 SERIES Bedienungsanleitung

Accu-Scope

Accu-Scope 3025-2 Betriebsanleitung

Accu-Scope

Accu-Scope 3025 Betriebsanleitung

Accu-Scope

Accu-Scope 3052-GEM Bedienungsanleitung

Accu-Scope

Accu-Scope EXC-120 SERIES Bedienungsanleitung

Accu-Scope

Accu-Scope 3065 Bedienungsanleitung

Accu-Scope

Accu-Scope 3078-HDR Bedienungsanleitung

Accu-Scope

Accu-Scope EXC-500 Bedienungsanleitung

Accu-Scope

Accu-Scope EXC-350-PH Bedienungsanleitung

Accu-Scope

Accu-Scope EXI-410 Series Bedienungsanleitung

Accu-Scope

Accu-Scope MT-40 Series Bedienungsanleitung

Accu-Scope

Accu-Scope EXC-400 Series Bedienungsanleitung

Accu-Scope

Accu-Scope 3019 Bedienungsanleitung

Accu-Scope

Accu-Scope EXC-400 Series Betriebsanleitung

Accu-Scope

Accu-Scope 3025 Series Bedienungsanleitung

Accu-Scope

Accu-Scope 3002 Bedienungsanleitung

Accu-Scope

Accu-Scope EXC-120-PL Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung