ACME LP-1600 BD30 Bedienungsanleitung

TV LIGHT PANEL 1600

LP-1600 BD30

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specifications

3. How To Set The Fixture

4. How To Control The Fixture

5. DMX 512 Configuration

6. DMX 512 Connections

7. Troubleshooting

8. Fixture Cleaning

1. Safety Introductions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user,

be sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the

power requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

The unit is for indoor use only and use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

Disconnect mains power before fuse replacement or servicing.

Replace fuse only with the same type.

Make sure there are not flammable materials close to the unit while operating as it is fire

hazard.

Use safety cable when fixes this unit.

Maximum ambient temperature is TA: 40℃and don’t operate it where the temperature

is higher than this.

The unit must be installed in a location with adequate ventilation, at least 2.5m from

adjacent surfaces, Be sure that no ventilation slots are blocked.

There are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service,

please contact the nearest authorized technical assistance center and always use the

same type spare parts. .

Don’t connect the device to any dimmer pack or power pack.

Do not look directly at the LED light beam while the fixture is on.

The housing must be replaced if they are visibly damaged.

Unit surface temperature may reach up to 60℃. Don’t touch the housing bare-hand

during its operation, and allow about 15 minutes to cool down before replacing bulb or

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

serving, as the unit could be very hot

Do not touch any wire during operation as high voltage might be causing electric shock.

Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.

Direct sunlight can cause heat to build up inside of the unit, which will seriously damage

unit.

2. Technical Specifications

It can be operated by DMX512 control or can be used as an individual unit without

controller.

It can be linked together as many as required in master/slave mode, and perform the

great built-in programmed lighting shows triggered by music.

Please use a 3 pin XLR cable/plug when connecting them together.

It features different pre-programmed chase patterns.

3 Channel modes.

Voltage：AC 100-240V, 50/60Hz

LED: Total 1600pcs,

CW: 800pcs, WW: 800pcs

Power consumption：160W

Fuse: T 6.3A

Dimension：540 x 556 x 115mm

Weight：9.7KG

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of

the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the

unit when installing the fixture.

For power supply, do not connect in series much more than 4 units, use another

mains supply for next 4 units.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

4. How To Set The Fixture

4.1Control Panel

○

1Display: To show the various menus and the selected functions

○

2 Indicator LED:

DMX

DMX input present

MASTER

Master Mode

SLAVE

Slave Mode

COLOR TEMP.

Flashing

Max. power consumption of CW/WW

○

3 Button:

To select the programming functions

DOWN

To go backward in the selected functions

To go forward in the selected functions

ENTER

To confirm the selected functions

○

4 Color Temperature: Adjust the color temperature from 3200k to 6500k, 25K as a step.

When the value is between 4825K and 4875K the green LED

indicator will light .It means the power consumption of CW/WW

color has reached the maximum.

○

5 Dimmer Adjust knob: Adjust brightness for the unit.

○

6 DMX output: For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.

○

7 DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal

○

8 Mains input: Connect to supply mains power

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the display.

Select the function by ENTER button and the display will blink. Use DOWN and UP button to

change the mode. Once the required mode has been selected, press ENTER button to

setup or it will automatically return to the main functions without any change after idling 30

seconds. Back to the functions without any change press MENU button. The main functions

are shown below:

DMX 512 Address setting

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX 512 address.

Once the address has been selected, press ENTER button to setup or automatically exit

menu mode without any change after 8 seconds. Back to the previous functions without any

change press MENU button.

Channel mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (2

channels) or (2 channels) or (3 Channels) mode. Once the mode has

been selected, press the ENTER button to setup or automatically exit menu mode without

any change after 8 seconds. To go back to the functions without any change press the

MENU button.

Master-Slave mode

Press the MENU button up to when the s shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (master mode) and (slave

mode). Once select, press ENTER button to setup or automatically exit menu mode without

any change after 8 seconds. To go back to the functions without any change press the

MENU button.

Manual mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the or

or (dimmer) mode, press the ENTER button to confirm, use UP and DOWN button

to adjust the value between 0 and 255, once select press ENTER button to setup or

automatically exit menu mode without any change after 8 seconds. To go back to the

functions without any change press the MENU button.

Blackout mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (blackout) or (normal).

Once select, press ENTER button to setup or automatically exit menu mode without any

change after 8 seconds. To go back to the functions without any change press the MENU

button.

Dimmer curve

Press the MENU button up to when the is shown on the display，Pressing ENTER

button and the present mode will blink. Use DOWN and UP button to select

the (dimmer mode 1) or (dimmer mode 2) or (dimmer mode 3) or

(dimmer mode 4). Once select, press ENTER button to setup or automatically exit

menu mode without any change after 8 seconds. To go back to the functions without any

change press the MENU button.

Optically Linear: The increase in light intensity appears to be linear as DMX value is

increased.

Square Law: Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.

S-curve: Light intensity control is finger at low levels and high levels and coarser at medium

levels.

LED display

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select (display on) or

(display off) mode. Once select, press ENTER button to setup or exit menu mode

without any change after 8 seconds. Back to the functions without any change press MENU

button again.

Display Inverse

Press MENU button until is blinking on the display. Use DOWN and UP button to

select (normal) or (inverse), press ENTER button to setup. Back to the

functions without any change press MENU button.

Self-Test

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the unit will run the built-in programmer for self-test. To go back to the functions

press the MENU button.

Fixture hours

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the number of working hours of the unit. To go back to the

functions press the MENU button.

Software version

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the version of software of the unit. To go back to the

functions press the MENU button again.

5. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave function

2. By DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the unit on, it will show type on the

display. After that the unit will be ready to receive DMX signal or run the built in programs.

5.1 Master/Slave Function

By linking the units in master/slave connection, the first unit will be master automatically. You

should set the master unit effect via its knobs, then the other units (slave) will lighting as the

same.

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME LED-MS600 PE Bedienungsanleitung

ACME

ACME TOUR PIXEL BAR 1010 II Bedienungsanleitung

ACME

ACME TV LIGHT PANEL 2000 Bedienungsanleitung

ACME

ACME Dragon Scan 50 LED-SC50B Bedienungsanleitung

ACME

ACME TRACK 10 Bedienungsanleitung

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME ICARUS 620 Bedienungsanleitung

ACME

ACME XP-5000SZ F Bedienungsanleitung

ACME

ACME Whack Bedienungsanleitung

ACME

ACME Andromeda Bedienungsanleitung

ACME

ACME Sandane Bedienungsanleitung

ACME

ACME DMX512 Dynamic Scan Bedienungsanleitung

ACME

ACME DOT Bedienungsanleitung

ACME

ACME Solaris Bedienungsanleitung

ACME

ACME BP-183 RGBW S R DXX Bedienungsanleitung

ACME

ACME Sunrise Bedienungsanleitung

ACME

ACME LED-PS10 Bedienungsanleitung

ACME

ACME IM-250 SP Bedienungsanleitung

ACME

ACME PIXEL LINE IP Bedienungsanleitung

ACME

ACME LIGHT PANEL 1000 Bedienungsanleitung

ACME

ACME ColorTec 250 LED-CC60 Bedienungsanleitung

ACME

ACME LED Move 600SE Bedienungsanleitung

ACME

ACME LED-256D-10W Bedienungsanleitung

ACME

ACME Stag Par MP-200 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung