ACME LED-256D-10W Bedienungsanleitung

LED-256D-10W

User Manual

Professional Entertainment Technology

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. Installation

4. How to Control the Unit

5. DMX 512 Configuration

6. DMX 512 Connection

7. Fixture Cleaning

1. Safety Instruction

WARNING

♦Please keep this User Manual for future consultation. If you sell the unit to another user,

be sure that they also receive this instruction booklet.

♦Unpack and check carefully there is no transportation damage before using the unit.

♦Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

♦It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

♦The unit is for indoor use only and use only in a dry location.

♦The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

♦Disconnect mains power before fuse replacement or servicing.

♦Replace fuse only with the same type.

♦Make sure there are not flammable materials close to the unit while operating as it is fire

hazard.

♦Use safety cable when fixes this unit.

♦In the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repair carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center and

always use the same type spare parts.

♦Do not touch any wire during operation as high voltage might be causing electric shock.

Please read the instruction carefully which including important

information about the installation, operation and maintenance.

2. Technical Specification

•It can be operated by DMX512 control or can be used as an individual unit without

controller.

•It can be linked together as many as required in master/slave mode, and perform the great

built-in programmed lighting shows triggered by music.

•Please use a 3 pin XLR cable/plug when connecting them together.

•Fan cooled.

•Voltage: AC 100V-240V 50/60Hz

•Fuse: T2A

•Power: 27 W

•LED：1X10W WHITE LED

•Dimension: 210X210X179 mm

•Weight: 1.8kg

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of

the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the

unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

4. How To Control The Unit

Three ways to operation:

A. Master/Slave operation

B. Easy controller CA-8

C. Universal DMX controller

A. Master/Slave operation

The unit can be linked together in daisy chain as many as you need in master/slave mode to

perform the great built-in pre-programmed lighting shows triggered by music.

In Master/Slave mode refer to the DMX settings below:

Master unit: DMX start address MUST be set to 001. (First DIP switch = ON, all other

are OFF)

Slave units: DMX start address may have any value but NOT 001 (example: set the

first 3 DIP switches to ON)

﹡Dipswitch 2 “OFF” has functions:

Perform the built-in pre-programmed by music.

﹡Dipswitch 2 “ON” has functions:

Auto mode: Eight Chase(At this mode press dip switch 3 will change the direction of

rotation，press dip switch 4,5,6 will change the speed)

﹡2-light show

Dipswitch 10”off” means the unit works normally and “on” means inversion. In order to

create a great light show, you can set dip switch 10 ”on” on any unit that is linking to the

master unit to get contrast movement to the master unit, even if you have two units only.

Dipswitch 10 on the first (Master) unit is no use for the 2-light show as it is the master unit

that operates the light show.

B. Easy Controller (by CA-8)

The easy remote control is used only in master/slave mode. By connecting to the 1/4”

microphone jack of the first unit (its DMX input plug is not used), you will find that the remote

control all the first unit will control all the other units for Stand by, Function and Mode. Built-in

lighting shows triggered by Easy Controller:

Stand by Blackout the unit

Function

1. Synchronous Strobe

2. Two light Strobe

3. Sound Strobe

Rotation Speed

1-8

Mode Strobe (LED OFF) Rotation (LED ON)

C. Universal DMX controller

When using a universal DMX controller to control the chain of units, you have to set DMX

address by Dip switches from 1 to 9 to make sure all the units will receive its DMX signal.

Dip switch 10 is used to keep OFF. Please refer to the following diagram to know how to

address your DMX 512 system in the binary code.

DMX 512 Address Chart:

Dip-switches # 1 # 2 # 3 # 4 # 5 # 6 # 7 # 8 # 9 #10

Value 1 2 4 8 16 32 64 128 256 Null

•Examples:

Channel 1：dip / on: #1 (=1)

Channel 3：dip / on: #1, #2 (1+2=3)

Channel 5：dip / on:, #1, #3(4+1=5)

Channel 7：dip / on: #1,#2, #3 (1+2+4=7)

5. DMX 512 Configuration

6. DMX 512 Connection

The DMX 512 is widely used in intelligent lightings and with a maximum of 512 channels.

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120

ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin

XLR-plug and plug it in the DMX-output of the last unit.

3. Connect the unit together in a ‘daisy chain’ by XLR plug from the output of the

unit to the input of the next unit. The cable can not be branched or split to a ‘Y’

cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables,

solder joints or corroded connectors can easily distort the signal and shut down

the system.

4. The DMX output and input connectors are pass-through to maintain the DMX

circuit, when power is connected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-512 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pins XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

7. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater

accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

EC - Declaration of Conformity

We declare that our products (lighting equipments) comply with the following

specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN61000-4-11: 1994.

Harmonized Standard

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

Part 1: General requirements

10-

11-

Innovation, Quality, Performance

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME Andromeda Bedienungsanleitung

ACME

ACME BF-1500ND B Bedienungsanleitung

ACME

ACME BIG BANG Bedienungsanleitung

ACME

ACME LED-HC101 II Bedienungsanleitung

ACME

ACME Energy Spot PRO Bedienungsanleitung

ACME

ACME SABER Mini Bedienungsanleitung

ACME

ACME LED-275 D Bedienungsanleitung

ACME

ACME DOT Bedienungsanleitung

ACME

ACME LED STROBE 50 Bedienungsanleitung

ACME

ACME COMET Bedienungsanleitung

ACME

ACME IL-2420 II Bedienungsanleitung

ACME

ACME TRACK 10 Bedienungsanleitung

ACME

ACME LED-WAV-10W Bedienungsanleitung

ACME

ACME Xperior 1500SZ Bedienungsanleitung

ACME

ACME LED-PS10D RGBW Bedienungsanleitung

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME LP-F1000 CW Bedienungsanleitung

ACME

ACME Thunder Bedienungsanleitung

ACME

ACME Xperior 700SZ Spot Bedienungsanleitung

ACME

ACME LED-900 A Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME STAGE PAR 400 ZOOM IP Bedienungsanleitung

ACME

ACME Libre Bedienungsanleitung

ACME

ACME LED Move 600SE Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung