ACME COOLIE 14FC Bedienungsanleitung

CONTENTS

1. Safety Instructions........................................................................................... 2

2. Techical Specfications ...................................................................................... 4

3. How To Set The Fixture.................................................................................... 5

3.1 Control Panel ............................................................................................. 5

3.2. Main Functions......................................................................................... 6

4. How To Control The Unit................................................................................ 12

4.1 Primary/Secondary Built-in Preprogram Function .................................. 12

4.2 Control By Universal DMX Controller ...................................................... 13

4.2.1 DMX512 Connection....................................................................... 13

4.2.2 Address Setting............................................................................... 14

4.2.3 DMX512 Configuration ................................................................... 14

5. Troubleshooting............................................................................................. 17

6. Fixture Cleaning............................................................................................. 17

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer

will not accept liability for any resulting defects or problems.

Unpack and check carefully to ensure that there is no transportation damage before using the

unit.

This product is suitable for wet locations. Do not immerse in water.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head

only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots is blocked, otherwise the unit will be overheated.

Before operation, ensure that you are connecting this product to the proper voltage in

accordance with the specifications in this manual or on the product’s specification label.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.Do not

operate this product at a lower or higher temperature.

DO NOT connect the device to any dimmer pack.

Keep flammable materials away from the fixture while operating to avoid fire hazard.

Make sure the power cord is not crimped or damaged; replace it immediately if damaged.

Avoid any flammable liquids, water or metal from entering the unit. Once it happens, cut off

the mains power immediately.

Please read the instruction carefully which includes important information

about the installation, usage and maintenance.

DO NOT operate in a dirty or dusty environment. DO clean the fixture regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid entanglement of the power cord with other wires.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the housing as there are no user serviceable parts inside.

DO NOT attempt to operate this unit if it becomes damaged. DO NOT attempt any repairs

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center if needed.

Disconnect this product from its power source before servicing.

DO use the original packaging if the device is to be transported.

Avoid direct eye exposure to the light source while the product is on.

DO NOT operate this product if you see damage on the housing, shields, or cables. Have the

damaged parts replaced by an authorized technician at once.

Installation:

The fixture should be fixed on the clamp. Always ensure that the unit is firmly fixed to avoid

vibration and slipping off during operation. Ensure that the trussing or area of installation must be

able to hold 10 times the weight without any deformation. Always install a safety cable that can

hold at least 12 times the weight of the fixture when installing.

DO install and operate by qualified operator. It must be installed in a place where there is out of

the reach of people.

2. Techical Specfications

Power Voltage:

100-240V~ 50/60Hz

Power Consumption:

165W

Light Source:

14x15W RGBW LED

Beam Angle:

13.5°

Spot Angle:

25.6°

Control:

DMX Channel : 4/5/7 Channel

Control Mode: DMX512, RDM, Primary/Secondary

Firmware upgrade via DMX link

Construction:

Display: LED display

Data In/Out: 3-pin XLR in/out

Power In/Out: Power Cord in/out

Protection Rating: IP66

Features:

Outstanding color mixing effect

Preset program in stand-alone mode

4 dimming curves, smooth dimming from 0~100%

Outstanding strobe effect with variable speed

Dimension/Weight:

302x230x350mm, 9.1kgs

11.9"x9.1"x13.8"in, 20.1lbs

302

350

230

Photometric Diagram:

3. How To Set The Fixture

3.1 Control Panel

1: Power: Water proof connectors for power input/output

2: DMX IN/OUT:

Water proof connectors for DMX512 operation, 3-pin XLR cable to link the units together

3: Display: To show the menu and the selected functions

Button:

4. MENU To select the programming functions

5. DOWN To go forward in the selected functions

6. UP To go backward in the selected functions

7. ENTER To confirm the selected functions

3.2. Main Functions

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until

the required function is shown on the monitor. Select the function by the ENTER button. Use the

UP/DOWN button to choose the submenu, press the ENTER button to store and automatically

return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.

The main functions are shown below:

Once you set to

, after running in show mode for 5 minutes without any

change or restarting the unit, the key board become locked. Press ENTER button to

enable the menu, the display will show , press UP and DOWN button until it

shows , then press ENTER to unlock.

DMX Address

Press the MENU button up to when the is shown on the display. Pres s ENTER button

and the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the

address has been selected, press ENTER button to setup or automatically exit menu mode without

any change after 30 seconds. Back to the previous functions without any change press MENU

button.

Channel Mode

Press the MENU button up to when the is shown on the display. Pres s ENTER button

and the display will blink. Use DOWN and UP button to select the (4 channels),

(5 channels) or (7 channels). Once select, press ENTER button to setup or

automatically exit menu mode without any change after 30 seconds. To go back to the functions

without any change press the MENU button.

Show Mode

Press the MENU button up to when the is shown on the display. Pres s ENTER button

and the display will blink. Use DOWN and UP button to select the (show 1) …

(show 16) or (Manual). After select the show mode, use DOWN and UP button to

adjust the value for fade mode and speed mode. Once select, press ENTER button to store or

automatically return to the main functions without any change after 30 seconds. To go back to the

previous functions without any change press the MENU button.

Pri./Sec. Mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Pri mary),

(Secondary 1) or (Secondary 2). Once select, press ENTER button to store or

automatically return to the main functions without any change after 30 seconds. To go back to the

previous functions without any change press the MENU button.

Dimmer Mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Dimme r Curve

1) … (Dimmer Curve 4). Once select, press ENTER button to store or automatically return

to the main functions without any change after 30 seconds. To go back to the previous functions

without any change press the MENU button.

Dimmer Speed

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Smooth),

(Fast). Once select, press ENTER button to store or automatically return to the main functions

without any change after 30 seconds. To go back to the previous functions without any change

press the MENU button.

DMX State

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Primary/Secondary),

(Blackout Mode) or (Hold). Once select, press ENTER button to store or

automatically return to the main functions without any change after 30 seconds. To go back to the

previous functions without any change press the MENU button.

LED

Press the MENUbutton up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (On) or

(Off). Once select, press ENTER button to store or automatically return to the main functions

without any change after 30 seconds. To go back to the previous functions without any change

press the MENU button.

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME DAZZLED COLORLED-430 Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME LED-PS10 Bedienungsanleitung

ACME

ACME Dragon Scan 50 LED-SC50B Bedienungsanleitung

ACME

ACME RAYZOR HYBRID Bedienungsanleitung

ACME

ACME ASTRO LED-256D Bedienungsanleitung

ACME

ACME Thunderstruck LP-2304 Bedienungsanleitung

ACME

ACME Beluga Bedienungsanleitung

ACME

ACME LED-3082 RGB Bedienungsanleitung

ACME

ACME FLASHDOT Bedienungsanleitung

ACME

ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

ACME

ACME CP-18TC Bedienungsanleitung

ACME

ACME LED-WAV-10W Bedienungsanleitung

ACME

ACME IL-2420 II Bedienungsanleitung

ACME

ACME Oxygen Bedienungsanleitung

ACME

ACME VOGUE Bedienungsanleitung

ACME

ACME Stage Par 220MP-220 Bedienungsanleitung

ACME

ACME Spartan Hybrid Bedienungsanleitung

ACME

ACME LED-SC252 Bedienungsanleitung

ACME

ACME Building wash Bedienungsanleitung

ACME

ACME Xperior 700SZ Spot Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME Pageant CM-200Z Bedienungsanleitung

ACME

ACME TV LIGHT PANEL 2000 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung