ACME LED-3082 RGB Bedienungsanleitung

15A

Innovation, Quality, Performance

"#$%!&'(!$)*!

$+)'!&'(!$)*!

LED-3082 RGB LED-3084 RGB

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specifications

3. Installation

4. How to set the unit

5. How to control the unit

6. DMX 512 Configuration

7. DMX 512 Connections

8. Troubleshooting

9. Fixture Cleaning

14A

EC - Declaration of Conformity

We declare that our products (lighting equipments) comply with the following

specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN61000-4-11: 1994.

Harmonized Standard

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

Part 1: General requirements

13A

9. Fixture Cleaning

The cleaning of internal must be carried out periodically to optimize light output. Cleaning

frequency depends on the environment in which the fixture operates: damp, smoky or

particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.

! Clean with soft cloth using normal glass cleaning fluid.

! Always dry the parts carefully.

! Clean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

Safety Introductions

WARNING

! Please keep this User Manual for future consultation. If you sell the fixture to another

user, be sure that they also receive this instruction booklet.

! Unpack and check carefully there is no transportation damage before using the fixture.

! It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

! Disconnect main power before servicing and maintenance.

! Maximum ambient temperature is Ta : 40!. Don’t operate it where the temperature is

higher than this.

! In the event of serious operating problem, stop using the fixture immediately. Never try

to repair the fixture by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance

center. Always use the same type spare parts.

! Do not connect the device to any dimmer pack.

! Do not touch any wire during operation and there might be a hazard of electric shock.

! To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain

or moisture.

! The housing must be replaced if they are visibly damaged.

! Do not look directly at the LED light beam while the fixture is on.

! There are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service,

please contact your nearest dealer.

! Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.

Direct sunlight can cause heat to build up inside of the unit, which will seriously damage

unit.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

For power supply, do not connect in series much more than 32 units, use

another mains supply for next 32 units.

2. Technical Specifications

! Fitted with 2 x 3W tri-color LEDs, the DMX Fury/Rage LED fills the entire room with

powerful and laser-like muticolor beams, delivering fabulous effects.

! Great built-in lighting shows under Master/Slave and Sound Active

! Full range dimmer and variable strobe effects.

! Optional CA-8 easy controller for enjoying instant lighting shows at you fingertips

! LED display for easy navigation

! Idear for discotheques, clubs, bars, parties, Mobile DJs, ect.

! Input Voltage: AC100V~240V 50/60Hz

! Power consumption: 16W

! Fuse: T 6.3A

! LED: 2 x 3W Tri-color LEDs 30000hrs rated

! Dimension: 296 x 271 x 140mm

! Weight: 4.0kgs (LED-3082 RGB)

3.8kgs (LED-3084 RGB)

3. Installation

The unit should be mounted via its screw

holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and

slipping while operating. Always ensure that

the structure to which you are attaching the

unit is secure and is able to support a weight

of 10 times of the unit’s weight. Also always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is

out of the touch of people and has no one pass by or under it.

12A

8. Troubleshooting

Following are a few common problems that may occur during operation. Here are some

suggestions for easy troubleshooting:

A. The fixture does not work, no light

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB

of the fixture or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may

cause damage or interference to DMX interface circuit.

C. Some fixtures don’t respond to the easy controller

1. You may have a break in the DMX cabling.

2. Check the LED for the response of the master/ slave mode signal.

D. No response to the sound

1. Make sure the fixture does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone.

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition.

11A

7. DMX512 Connections

The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.

1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the

fixture to the input of the next fixture. The cable cannot be branched or split to a “Y”

cable. Inadequate or damaged cables, soldered joints or corroded connectors can

easily distort the signal and shut down the system

2. The DMX output and input connectors are pass-through to maintain the DMX circuit

when one of the units’ power is disconnected.

3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal

errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a

3-pin XLR-plug and plug it in the DMX-output of the last fixture.

4. Each lighting fixture needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

5. 3 pin XLR connectors are more popular than 5 pins XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),

Pin4/5: not used

4. How toset the unit

4.1Rear Panel

1Display: To show the various menus and the selected functions

LED:

2 DMX On DMX input present

3 MASTER On Master Mode

4 SLAVE On Slave Mode

5 SOUND Flashing Sound activation

Button:

6 MENU To select the programming functions

7 DOWN To go backward in the selected functions

8 UP To go forward in the selected functions

9 ENTER To confirm the selected functions

10 Microphone"Receive music for the sound active.

11 DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal.

12 output"For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.

13 Only for remote control"By connect to the 1/4’’ microphone jack to control the unit for

Stand by, Function and Mode function.

14 Safety Ring"For attached the safety cable.

15 Mains output"Connect to supply mains power for the next unit.

16 Mains input"Connect to supply mains power.

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the display.

Select the function by ENTER button and the display will blink. Use DOWN and UP button to

change the mode. Once the required mode has been selected, press ENTER button to

setup or it will automatically return to the main functions without any change after idling 30

seconds. Back to the functions without any change press MENU button. The main functions

are shown below:

DMX 512 Address Setting

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX 512 address.

Once the address has been selected, press ENTER button to setup or automatically exit

menu mode without any change after 30 seconds. Back to the previous functions without

any change press MENU button.

10A

6. DMX512 Configuration

1 & 3-CH modes:

5.2 Easy Controller (by CA-8)

The easy remote control is used only in master/slave mode. By

connecting to the 1/4” microphone jack of the first unit, you will find that

the remote controller on the first unit will control all the other units for

Stand by, Function and Mode selection

5.3 DMX Controller

Using universal DMX controller to control the units, you have to set DMX address from 1 to

512 channel so that the units can receive DMX signal.

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press and keep ENTER button pressed up to when

the display stops blinking or storing automatically 8 seconds later. To go back to the

functions without any change press the MENU button again. If you use please refer to the

following diagram to address your DMX512 channel for the first 4 /2 units.

1 channel mode:

3 channels mode:

Blackout Blackout the unit

Function

1. SynchroStrobe

2. Asynchro Strobe

3. Sound Strobe

Select Show

(Show 1-8)

Select Speed

1. Slow

2. Middle

3. Fast

Mode Sound/Strobe

(LED OFF)

Show

(LED ON) LED blinking

Channel Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (1 channel) or (3

channels ) mode. Once select, press the ENTER button to setup or automatically exit menu

mode without any change after 30 seconds. To go back to the functions without any change

press the MENU button

Slave Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (master) or (slave 1) or

(Slave 2) mode. Once select, press the ENTER button to setup or automatically exit

menu mode without any change after 30 seconds. To go back to the functions without any

change press the MENU button

Show Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (Random show) or (show

1) or (Show 2) or … or (show8). Once select, press ENTER button to

store or automatically exit menu mode without any change after 30 seconds. To go back to

the functions without any change press the MENU button

Sound

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (sound on) or (sound off).

Once select, press ENTER button to setup or automatically exit menu mode without any

change after 30 seconds. To go back to the functions without any change press the MENU

button

Blackout mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (blackout) or (normal).

Once select, press ENTER button to setup or automatically exit menu mode without any

change after 30 seconds. To go back to the functions without any change press the MENU

button.

LED display

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select (display on) or

(display off) mode. Once select, press ENTER button to setup or exit menu mode

without any change after 30 seconds. Back to the functions without any change press

MENU button again.

Display Inverse

Press MENU button until is blinking on the display. Use DOWN and UP button to

select (normal) or (inverse), press ENTER button to setup. Back to the

functions without any change press MENU button.

Self-Test

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the unit will run the built-in programmer for self-test. To go back to the functions

press the MENU button.

Fixture Hours

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the number of working hours of the unit. To go back to the

functions press the MENU button.

"Software version

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the version of software of the unit. To go back to the

functions press the MENU button.

"Reset

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and all the motors will back to their home position.

4.3 Home Position Adjust

Press Enter button for about 5 seconds, “OPAN” will shown on the display, press ENTER

button to confirm, then use DOWN and UP button to adjust the home position (-127 - 127) of

the motor. Once the position has been selected, press the ENTER button to setup or exit the

offset mode without any change press the MENU button.

5. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave built-in preprogram function

2. By easy controller

3. By DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the unit on, it will show “L308” on the

display. After that the unit will be ready to receive DMX signal or run the built in programs.

5.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the other units to

give an automatic, sound activated, synchronized light show. This function is good when you

want an instant show. You have to set the first unit in master mode and select

(random show), (show 1) or #or (show 8). Its DMX input jack will

have nothing plugged into it, and Its master LED will be constantly on and sound LED will

flash to the music. The other units will have to select (normal) or (2 light

show) mode, Their DMX cables plugged into the DMX input jacks (daisy chain) and the

slave led lights will constantly on.

2-light show

In slave mode, means the unit works as the master unit and means 2-light

show. In order to create a great light show, you can set on the second unit to get

contrast movement to each other, even if you have two units only.

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME MP-12FC Bedienungsanleitung

ACME

ACME Neozone Bedienungsanleitung

ACME

ACME Xperior XP-380 BEAM IP F Bedienungsanleitung

ACME

ACME Building wash Bedienungsanleitung

ACME

ACME Beluga Bedienungsanleitung

ACME

ACME iSolution Bedienungsanleitung

ACME

ACME BTDG40 Bedienungsanleitung

ACME

ACME Uploader II Bedienungsanleitung

ACME

ACME Warrior Scan 50 LED-SC50C Bedienungsanleitung

ACME

ACME CA-DC6S Bedienungsanleitung

ACME

ACME CM-150 PAGEANT 150 Bedienungsanleitung

ACME

ACME Solaris Bedienungsanleitung

ACME

ACME LED-0408 Bedienungsanleitung

ACME

ACME LED-MTX6S-8W Bedienungsanleitung

ACME

ACME GEIST BSWF Bedienungsanleitung

ACME

ACME Spartan Hybrid C Bedienungsanleitung

ACME

ACME IM-250 SP Bedienungsanleitung

ACME

ACME Gemini Bedienungsanleitung

ACME

ACME LP-1600 BD30 Bedienungsanleitung

ACME

ACME ICARUS 620 Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME Dynamic 25 Roller LED-SC25B Bedienungsanleitung

ACME

ACME LED-WAV-10W Bedienungsanleitung

ACME

ACME LED-256D-10W Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung