Advantech PCI-1220U Bedienungsanleitung

PCI-1220U

2-axis Universal PCI Stepping/

Pulse-type Servo Motor Control

Card

User Manual

PCI-1220U User Manual ii

This documentation and the software included with this product are

copyrighted 2009 by Advantech Co., Ltd. All rights are reserved.

Advantech Co., Ltd. reserves the right to make improvements in the

products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or

transmitted in any form or by any means without the prior written

permission of Advantech Co., Ltd. Information provided in this manual is

intended to be accurate and reliable. However, Advantech Co., Ltd.

assumes no responsibility for its use, nor for any infringements of the

rights of third parties which may result from its use.

Acknowledgments

PC-LabCard is a trademark of Advantech Co., Ltd. IBM and PC are

trademarks of International Business Machines Corporation. MS-DOS,

Windows®, Microsoft®Visual C++ and Visual BASIC are trademarks of

Microsoft® Corporation. Intel®and Pentium®are trademarks of Intel

Corporation. Delphi and C++Builder are trademarks of Inprise

Corporation.

CE notification

The PCI-1220U, developed by ADVANTECH CO., LTD., has passed the

CE test for environmental specifications when shielded cables are used

for external wiring. We recommend the use of shielded cables. This kind

of cable is available from Advantech. Please contact your local supplier

for ordering information.

Printed in Taiwan September 2009

iii

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its prod-

ucts will be free from defects in materials and workmanship for two years

from the date of purchase.

This warranty does not apply to any products which have been repaired or

altered by persons other than repair personnel authorized by Advantech,

or which have been subject to misuse, abuse, accident or improper instal-

lation. Advantech assumes no liability under the terms of this warranty as

a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous test-

ing, most of our customers never need to use our repair service. If an

Advantech product is defective, it will be repaired or replaced at no

charge during the warranty period. For out-of-warranty repairs, you will

be billed according to the cost of replacement materials, service time and

freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For

example, CPU speed, Advantech products used, other hardware

and software used, etc.) Note anything abnormal and list any

onscreen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your man-

ual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return

merchandize authorization) number from your dealer. This allows

us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and

Replacement Order Card and a photocopy proof of purchase date

(such as your sales receipt) in a shippable container. A product

returned without proof of the purchase date is not eligible for war-

ranty service.

5. Write the RMA number visibly on the outside of the package and

ship it prepaid to your dealer.

PCI-1220U User Manual iv

Technical Support and Assistance

Step 1. Visit the Advantech web site at www.advantech.com/support

where you can find the latest information about the product.

Step 2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before

you call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, appli-

cation software, etc.)

- A complete description of the problem

- The exact wording of any error messages

Packing List

Before setting up the system, check that the items listed below are

included and in good condition. If any item does not accord with the

table, please contact your dealer immediately.

• PCI-1220U

• Companion CD-ROM (DLL driver included)

• User Manual

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the

products from damage.

1. To avoid electrical shock, always disconnect the power from your

PC chassis before you work on it. Don't touch any components on

the CPU card or other cards while the PC is on.

2. Disconnect power before making any configuration changes. The

sudden rush of power as you connect a jumper or install a card may

damage sensitive electronic components.

v Table of Contents

Contents

Chapter 1 Introduction ..................................................... 2

1.1 Features ............................................................................. 2

1.2 Applications ...................................................................... 5

1.3 Installation Guide .............................................................. 5

1.4 Accessories........................................................................ 6

Chapter 2 Installation ....................................................... 8

2.1 Unpacking ......................................................................... 8

2.2 Driver Installation ............................................................. 9

2.3 Installation Instructions ..................................................... 9

Chapter 3 Signal Connections ........................................ 12

3.1 I/O Connector Pin Assignments...................................... 12

3.2 Location of Jumpers and DIP switch .............................. 12

Figure 3.1:I/O Connector Pin Assignments ................. 13

Table 3.1:I/O Connector Signal Description ............... 14

Figure 3.2:Location of Jumpers & DIP Switch ........... 16

Table 3.2:BoardID register .......................................... 16

Table 3.3:BoardID setting ............................................ 16

3.3 Output Pulse Definition................................................... 17

Figure 3.3:Output Signal Loop for Drive Pulses ......... 17

Table 3.4:JP1~4 Jumpers ............................................. 17

Figure 3.4:Photo Coupler Input Interface .................... 18

Figure 3.5:Line Driver Input Interface ........................ 18

3.4 General Purposed Output ................................................ 19

Figure 3.6:General Purpose Output ............................. 19

3.5 Over Traveling Limit Switch Input................................. 19

Figure 3.7:Movement Limit Input Signals .................. 20

Figure 3.8:Photo Sensor in the Limit Input Signal ...... 20

3.6 Deceleration/Instantaneous Stop Switch Input ............... 21

Figure 3.9:Deceleration/Instantaneous Stop Input ....... 21

3.7 General Purposed Input for Servo Drives ....................... 22

Figure 3.10:Input Signal for Servo Motor ................... 22

3.8 Encoder Input .................................................................. 23

Figure 3.11:Circuit Diagram of Encoder Feedback ..... 23

Figure 3.12:Differential-output Line Driver ................ 24

Figure 3.13:Open Collector Output Encoder ............... 24

3.9 External Pulse Control Input........................................... 25

Figure 3.14:External Drive Operation Signals ............ 25

Figure 3.15:Example of Connecting to Jog ................. 25

3.10 Emergency Stop Input (EMG) ........................................ 26

Figure 3.16:Emergency Stop Input Signal ................... 26

Table 3.5:Jumper Settings of JP5 ................................ 26

3.11 External Power Input (VEX)........................................... 26

3.12 Interrupt Setting............................................................... 27

Figure 3.17:Circuit Diagram of Interrupt Setting ........ 27

PCI-1220U User Manual vi

3.13 Connection Examples for Motor Drivers ........................ 28

3.13.1 Connection to Step Motor Drivers ............................... 28

Figure 3.18:Connecting to KR515M Drive ................. 28

Figure 3.19:Connecting to UPK Step Drive ................ 29

3.13.2 Connection to Servo Motor Drivers ............................. 30

Figure 3.20:MINAS X Series AC Servo Motor Drive 30

3.14 Field Wiring Considerations ........................................... 31

3.15 I/O Signal Timing............................................................ 32

3.15.1 Power On RESET ........................................................ 32

Figure 3.21:Timing Diagram of Power On Reset ........ 32

3.15.2 Individual Axis Driving ............................................... 32

Figure 3.22:Individual Axis Driving ........................... 32

3.15.3 Interpolation Driving ................................................... 33

Figure 3.23:Timing Diagram of Interpolation Driving 33

3.15.4 Input Pulse Timing ....................................................... 33

Figure 3.24:Quadrature Pulse of Encoder Input .......... 33

Figure 3.25:Timing Diagram of Up/Down Pulse Input 33

3.15.5 Instantaneous Stop Timing .......................................... 34

Figure 3.26:External Instantaneous Stop Signal .......... 34

Figure 3.27:Instantaneous Stop Instruction ................. 34

3.15.6 Deceleration Stop Timing ............................................ 34

Figure 3.28:External Deceleration/Stop Signal ........... 34

Figure 3.29:Deceleration/Stop Instruction ................... 34

3.16 TTL Level Position Compare Output.............................. 35

Table 3.6:Jumper Settings of JP6 ................................ 35

Appendix A Specifications ................................................. 38

A.1 Axes........................................ 38

A.2 Digital Input/Output ........................... 39

A.3 Input Pulse for Encoder Interface ................. 39

A.4 External Signals Driving ........................ 40

A.5 Other Functions ............................... 40

A.6 General ............................................................................ 41

Appendix B Block Diagram ............................................... 44

Appendix C Wiring with Third-Party Motor Drivers .... 46

Figure C.1:Mitsubishi MR-J2S Series Motor Driver ... 46

Figure C.2:Oriental LIMO EZMC Motor Driver ........ 47

Figure C.3:Panasonic MINAS-A Series Motor Driver 48

Figure C.4:Yaskawa SGDM Series Motor Driver ....... 49

CHAPTER

Introduction

This chapter introduces PCI-1220U and

lists features and specifications.

PCI-1220U User Manual 2

Chapter 1 Introduction

PCI-1220U 2-axis Stepping/Pulse-type Servo Motor Control Card is

designed for general-purpose motion applications. The card simplifies

stepping and pulse-type servo motor control.

The cards’ intelligent NOVA MCX312 motion ASIC builds in a variety

of motion control functions, such as 2-axis linear interpolation, 2-axis cir-

cular interpolation, T/S-curve acceleration/deceleration rate and more.

PCI-1220U performs motion control functions without processor load

during driving. For advanced applications, we supply Windows DLL

drivers and user-friendly examples to decrease your programming load.

Moreover, through a free bundled motion utility, you can complete con-

figuration and diagnosis easily.

1.1 Features

PCI-1220U provides users with the most requested motor control func-

tions as seen below:

• Independent 2-axis motion control

• Support hand wheel and jog function

• 2-axis linear interpolation function

• 2-axis circular interpolation function

• Continuous interpolation function

• Programmable T/S-curve acceleration and deceleration

• Up to 4MPPS pulse output for each axis

• Two pulse output types: Up/Down or Pulse/Direction

• Up to 1 MHz encoder input for each axis

• Two encoder pulse input types: A/B phase or Up/Down

• Position management and software limit switch function

• BoardID Switch

• Free Motion Utility bundled for configuration and diagnosis

• "Go home” functions

• Universal PCI Bus for both 3.3 and 5 V PCI slots

3 Chapter 1

The Advantech PCI-1220U offers the following main features:

Individual Control for 2 Axes

Each of the axes has identical capabilities, and is controlled by the same

method of operation with constant speed, trapezoidal or S-curve driving.

Programmable T/S-curve Acceleration and Deceleration

Each of four axes can be preset individually with S-curve or trapezoidal

acceleration/deceleration rates. When using S-curve acceleration to con-

trol driving speed, output pulse is generated in parabolic-shaped accelera-

tion or deceleration curves, and the triangular curve phenomenon will not

occur through the NOVA MCX-312-motion ASIC design concept.

Linear and Circular Interpolation

Two axes can be used to execute linear interpolation driving and circular

arc interpolation control. The interpolation speed range is from 1 PPS to 4

MPPS.

Powerful Position Management Function

Each axis is equipped with a 32-bit logical position counter and a 32-bit

real position counter. The logical position counter counts the axis’ pulse

output number and the real position counter is recorded with the feedback

pulse from the outside encoder or linear scale.

Speed Control

The speed range of the pulse output is from 1PPS to 4MPPS for constant

speed, trapezoidal or S-curve acceleration/deceleration driving. The

accuracy of the frequency of the pulse output is less than +/- 0.1% (at

CLK=16 MHz). The speed of driving pulse output can be freely changed

during the driving.

Continuous Interpolation

Different interpolation methods can be used continuously, for example:

Linear interpolationCircular interpolationLinear interpolation.

The maximum driving speed of performing continuous interpolation is 2

MPPS.

PCI-1220U User Manual 4

Constant Vector Speed Control

This function performs a constant vector speed. During the interpolation

driving, MCX312 can set a 1.414 times pulse cycle for 2-axis simultane-

ous pulse output that keeps constant speed during driving.

Compare Register and Software Limit

Each axis has two 32-bit compare registers for logical position counter

and real position counter. The comparison result can be read from the sta-

tus registers. The comparison result can be notified by an interrupt signal.

These registers can be also functioned as software limits.

Driving by External Signal

It is possible to control each axis by external signals. The +/- direction

fixed pulse driving and continuous driving can be also performed through

the external signals. This function is used for JOG or teaching modes, and

will share the CPU load.

Input/ Output Signal

Each axis has 2 points of general input signals. Besides, there are ORG

and EZ signals for high-speed near-by home search, home search and z-

phase search during the home returning. Each axis is with 4 output points

for general output.

Servo Motor Feedback Signals

Each axis includes input pins for servo feedback signals such as in-posi-

tioning, close loop positioning control and servo alarm.

Interrupt Signals

Interrupt signals can be generated when: (1) the start/finish of a constant

speed drive during the trapezoidal driving, (2) the end of driving, and (3)

the compare result higher/lower the border-lines of the position counter.

An interrupt signal can be also generated during the interpolation driving.

Inhaltsverzeichnis

Andere Advantech PCI-Karte Handbücher

Advantech

Advantech PCM-2312 Bedienungsanleitung

Advantech

Advantech MIC-3640 Bedienungsanleitung

Advantech

Advantech PCI-1737U Installations- und Betriebshandbuch

Advantech

Advantech PCIE-1730H-AE Bedienungsanleitung

Advantech

Advantech PCA-5610 Installations- und Betriebshandbuch

Advantech

Advantech DSPC-8661-PCXE Bedienungsanleitung

Advantech

Advantech PCIE-1680 Bedienungsanleitung

Advantech

Advantech PCI-1758 Series Bedienungsanleitung

Advantech

Advantech PCIE-1805 Bedienungsanleitung

Advantech

Advantech PCI-1202 Bedienungsanleitung

Advantech

Advantech PCI-1730U Bedienungsanleitung

Advantech

Advantech DVP-7635HE Bedienungsanleitung

Advantech

Advantech PCI-1710U Bedienungsanleitung

Advantech

Advantech PCI-1757UP Bedienungsanleitung

Advantech

Advantech PCIE-1760 Bedienungsanleitung

Advantech

Advantech PCM-3614I Installations- und Betriebshandbuch

Advantech

Advantech PCI-1751U Bedienungsanleitung

Advantech

Advantech PCIE-1752 Bedienungsanleitung

Advantech

Advantech PCN-6351 Series Bedienungsanleitung

Advantech

Advantech ARK-5261 Installations- und Betriebshandbuch

Advantech

Advantech PCI-1734 Installations- und Betriebshandbuch

Advantech

Advantech PCI-1780 Bedienungsanleitung

Advantech

Advantech PCA-6194 Bedienungsanleitung

Advantech

Advantech PCI-1736UP Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung