AFe Power Momentum hd Bedienungsanleitung

advanced FLOW engineering

Instruction Manual P/N: 50-73004

Make: FORD Model: F-250/350/450/550 Year: 2008-2010 Engine: V8-6.4L (td)

The Next

Generation

of Intakes

Label Qty. Description Part Number

A 1 Housing 05-73004B2

B 1 Plug, Urethane 05-01202

C 1 Clamp, T-bolt (8-5/16") 03-50267

D 1 PRO 10R (Blue Media) 20-91061

E 2 Screw, M4 03-50221

F 1 Tube 05-73004B1

G 1 Clamp, Mini 03-50023

H 1 Fitting, Elbow 03-50178

I 1 Grommet,Rubber 03-50139

J 2 Clamp, T-bolt (3") 03-50320

K 1 Coupling, Silicone Hump 05-01245

L 1 T20 Torx Bit 03-50066

Installation will require the following tools:

1/4" Nut Driver, 5/16" or 8mm Nut Driver, Wire Cutters, Flat Head Screw driver, 10mm and 7/16" Socket,

Ratchet and Extension.

Note: Legal in California for use on race vehicles only. The use of this device on vehicles used on public

streets or highways is strictly prohibited in California and others states that have adopted California

emission regulations.

• Please read the entire instruction manual before proceeding.

• Ensure all components listed are present.

• If you are missing any of the components, call technical support at 951-493-7100

or e-mail tech@afepower.com.

• Ensure you have all necessary tools before proceeding.

• Do not attempt to work on your vehicle when the engine is hot.

• Disconnect both the negative battery terminal before proceeding.

• Retain factory parts for future use.

Page 2

aFepower.com

Page 3

Refer to Figure A for steps 1-6

Step 1: Disconnect both batteries.

Step 2: Loosen the (2) Intake tube clamps using an 8mm nut driver.

Step 3: Disconnect the wire harness 1 from the Mass Air Flow (MAF) sensor.

Step 4: Disconnect the wire harness 2 from the ﬁlter minder.

Step 5: Remove the crank case breather hose clamp by prying it open with a screw driver or cutting it.

Then pull the crank case breather hose from the intake tube.

Step 6: Remove the factory intake tube out of the vehicle. Take the auxiliary air line out of the factory air

box. Remove the factory air box by pulling it ﬁrmly out of the factory grommets.

REMOVAL

Page 4

Figure A

Refer to Figure B for step 7

NOTE: Wipe the ﬁlter ﬂange with acetone to remove excess oil.

Step 7: Install the ﬁlter D in the Momentum HD housing A and install the large T-bolt clamp C .

Install the medium T-bolt clamp D on the ﬁlter. Do not tighten yet.

IMPORTANT: Prior to installation of T-bolt clamp, we recommend that you form the T-bolt clamps by

installing it in its intended position and tightening.

INSTALL

aFepower.com

Page 5

Figure B

Refer to Figure C for steps 8-12

Step 8: Remove the MAF sensor and ﬁlter minder with rubber grommet (Will be reused) from

the factory air intake.

Step 9: Install the factory ﬁlter minder grommet and ﬁlter minder onto the Momentum HD intake tube.

Step 10: Install the MAF sensor into the Momentum HD intake tube using the provided screws E .

Step 11: Install supplied rubber grommet I onto the intake tube F for the crank case breather.

Step 12: Install supplied coupling K to the intake tube. (Do not install the clamps at this time).

Figure C

Page 6

INSTALL

Refer to Figure D for step 13

Step 13: Place the Momentum HD housing in the truck. DO NOT push it completely into its ﬁnal location.

Figure D

INSTALL

aFepower.com

Page 7

Page 8

Refer to Figure E for steps 14-15

Step 14: Connect the Momentum HD tube to the turbo. Leave the tube at a 45-degree angle.

Step 15: PLEASE READ CAREFULLY: Rotate the intake tube down into the ﬁlter and at the same time

you will need to push the housing into the factory grommets. When secure in the grommets,

the tube will ﬁt into the ﬁlter. Install the auxiliary air line into the housing 4 .

Figure E

INSTALL

Refer to Figure F for steps 16-17

Step 16: Install the (2) supplied T-bolt clamps J over the coupling at the turbo, and tighten. Also tighten

the T-bolt clamps on the ﬁlter and on the housing.

Step 17: Install the crank case breather hose into the rubber grommet on the Momentum HD intake

tube. Early models (built before 5/6/2007) 90-degree ﬁtting can be reused. For later model

(built after 5/7/2007) production tubes, cut or pry the upper clamp off and use the

provided plastic 90-degree ﬁtting H & mini clamp supplied G .

aFepower.com

Page 9

Figure F

INSTALL

Refer to Figure G for steps 18-20

Step 18: Reconnect the harness to the MAF sensor and the Filter Minder.

Step 19: Check all components are tight and secured.

Step 20: Tighten all clamps and re-connect the batteries. Your installation is now complete.

Use the furnished plug B to close off the front auxiliary air inlet to completely seal the airbox.

NOTE: Retighten all connections after approximately 100-200 miles.

Page 10

Figure G

INSTALL

Andere Handbücher für Momentum hd

Inhaltsverzeichnis

Andere aFe Power Autozubehör Handbücher

aFe Power

aFe Power Magnum FORCE 54-13035D Bedienungsanleitung

aFe Power

aFe Power 440-401006-N Bedienungsanleitung

aFe Power

aFe Power 50-70007D Bedienungsanleitung

aFe Power

aFe Power Scorpion Bedienungsanleitung

aFe Power

aFe Power Quantum 2500 Bedienungsanleitung

aFe Power

aFe Power 46-71110A Bedienungsanleitung

aFe Power

aFe Power 52-10002D Bedienungsanleitung

aFe Power

aFe Power 46-20299-B Bedienungsanleitung

aFe Power

aFe Power 46-70022 Bedienungsanleitung

aFe Power

aFe Power 77-42008 Bedienungsanleitung

aFe Power

aFe Power 51-82722 Bedienungsanleitung

aFe Power

aFe Power advanced FLO engineering Bedienungsanleitung

aFe Power

aFe Power 54-12208 Bedienungsanleitung

aFe Power

aFe Power advanced FLOW engineering Bedienungsanleitung

aFe Power

aFe Power Scorcher Bedienungsanleitung

aFe Power

aFe Power 54-10468 Bedienungsanleitung

aFe Power

aFe Power 77-47001 Bedienungsanleitung

aFe Power

aFe Power SCORCHER BLUE 77-83043 Bedienungsanleitung

aFe Power

aFe Power dfs780 Bedienungsanleitung

aFe Power

aFe Power 77-83046 Bedienungsanleitung

aFe Power

aFe Power SCORPION 79-21008L Bedienungsanleitung

aFe Power

aFe Power SCORCHER GT 77-47004 Bedienungsanleitung

aFe Power

aFe Power 54-12742 Bedienungsanleitung

aFe Power

aFe Power Scorpion 79-21001L Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung

aFe Power Momentum hd Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken