Agilent Technologies Archon Bedienungsanleitung

Agilent Technologies

Archon Connections

to Varian 3400 and 3600 GC's with Star Workstation

Remote I/O Cable Hookup Instructions

Archon to Tekmar LSC 2000/3000 to Varian 3400 and

3600 GC's

Archon Connections to Varian 3400 and 3600 GC's with Star Workstation

Remote I/O Cable Hookup Instructions:

Archon to Tekmar LSC 2000/3000 to Varian 3400 and 3600 GC's

When connecting to a Varian series 3400 or 3600 GC with Star Workstation,

connectors from both the Archon I/O cable and the Star Workstation cable

must access the J16 and J23 connectors on the GC motherboard. This is

possible using the J16 Splitter (p/n DY-700030-00) and the J23 Splitter

(p/n DY-700031-00) following the instructions below:

1Turn off the power and unplug the power cord from the GC. Remove the

top panels to allow access to the GC motherboard.

2Route the GC-end of the Archon I/O cable and the GC-end of the Star

Workstation cable through the back panel of the GC (see Star Workstation

installation diagram).

3Connect the 5-pin female Molex connector (P23) from the Star Workstation

cable to the male connector on the J23 Splitter with 4 pins (the second

position lacks a pin).

4Connect the 5-pin female Molex connector from the Archon I/O cable to the

5-pin male connector on the J23 Splitter.

5Connect the J23 Splitter to the J23 connector on the GC motherboard (see

GC manual for motherboard layout schematic).

6Connect the 4-pin female Molex connector from the Archon I/O cable to

either of the 4-pin male connectors on the J16 Splitter.

7Connect the 4-pin female Molex connector (P16) from the Star Workstation

cable to either of the 4-pin male connectors on the J16 Splitter.

2 Remote I/O Cable Hookup Instructions

Archon Connections

8Connect the J16 Splitter to the J16 connector on the GC motherboard (see

GC manual for motherboard layout schematic).

9Complete the installation of the Archon I/O cable and of the Star

Workstation cable according to the standard instructions for those cables.

The following sequence occurs when the Archon and a Purge and Trap unit is

configured with the Varian 3400 and 3600 GC with Star Workstation:

1The Archon begins its sample handling after receiving a Ready signal from

the Purge and Trap unit. As configured above, the Purge and Trap goes to

Ready without waiting for the GC. This allows the user to prepare the GC

or Workstation while the sample is being purged and collected in the Purge

and Trap.

2The Purge and Trap collects the purged sample onto its trap and waits for a

Ready signal from the GC. This occurs after the Workstation issues a

Ready signal to the GC through the Workstation's cable plug attached to the

GC's J16 Ready-In pins, 1 and 2. In turn, the GC sends a Ready-Out signal

from its J23 pins 1 and 3 into the Archon I/O cable.

3When the Purge and Trap has both completed its purge cycle and detected a

Ready signal from the GC, the Purge and Trap desorbs the sample from its

trap and issues a Desorb-Out signal to both the Archon and to the Varian

GC. This signal travels through the Remote I/O cable supplied with the

Archon.

4The Desorb-Out signal from the Purge and Trap starts the Archon's

AutoDrain cycle which drains the sparge vessel if a water-sample method is

being run on the Archon.

5The Desorb-Out signal simultaneously travels through the Archon Remote

I/O cable to its connector attached to the GC's J16 Start-In pins, 3 and 4,

and initiates the GC run. The GC in turn initiates a Start-Out signal

through J23 pins, 4 and 5, which triggers the Workstation to begin data

collection.

NOTE

Archon Connections

Remote I/O Cable Hookup Instructions 3

Agilent Technologies

Warranty

The material contained in this document is provided “as is,” and is subject to being changed, without notice,

in future editions. Further, to the maximum extent permitted by applicable law, Agilent disclaims all warran-

ties, either express or implied, with regard to this manual and any information contained herein, including

but not limited to the implied warranties of merchantability and fitness for a particular purpose. Agilent shall

not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or

performance of this document or of any information contained herein. Should Agilent and the user have a

separate written agreement with warranty terms covering the material in this document that conflict with

these terms, the warranty terms in the separate agreement shall control.

©Agilent Technologies, Inc. 2012

Printed in USA

First edition, March 2012

Agilent Technologies, Inc.

2850 Centerville Road

Wilmington, DE 19808-1610 USA

*G7361-90687*

G7361-90687

Andere Agilent Technologies Laborausrüstung Handbücher

Agilent Technologies

Agilent Technologies Labware MiniHub Bedienungsanleitung

Agilent Technologies

Agilent Technologies Cary 8454 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1260 Infinity Bedienungsanleitung

Agilent Technologies

Agilent Technologies MX3000P Bedienungsanleitung

Agilent Technologies

Agilent Technologies G2570A GC/MSD Betriebsanleitung

Agilent Technologies

Agilent Technologies PlateLoc Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1260 Infinity II Bedienungsanleitung

Agilent Technologies

Agilent Technologies Magnis G9710A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1260 Infinity Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8511B Service-Handbuch

Agilent Technologies

Agilent Technologies 55B AA Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5975 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7890A Handbuch

Agilent Technologies

Agilent Technologies SIPS 10 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5975 MSD Bedienungsanleitung

Agilent Technologies

Agilent Technologies TS-5400 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7820A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Medalist i1000 Bedienungsanleitung

Agilent Technologies

Agilent Technologies G1574A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6890 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7890A GC Benutzerhandbuch

Agilent Technologies

Agilent Technologies 1260 Infinity G1315C Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 1260 Infinity Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung

Yamato

Yamato BM510 Bedienungsanleitung