Argos 246/6848 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 70.5cm

Depth - 52cm

Height - 183cm

1 Drawer 2 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 6 - 09/09/14

Important - Please read these instructions fully before starting assembly

ALR3003

246/6848

248/4150

247/3329

Issue 2 - 02/07/12 - Plinth ID corrected to D1713A and added note at step 15 to use poly block.

Issue 3 - 07/12/12 - Dimemsions of Drawer Base T539 changed to 650 x 317mm.

NEW MK2 VERSION

Issue 4 - 13/06/13 - Rebates taken off and main panel numbers updated.

Issue 5 - 03/04/14 - Drawer box sizes increased.

Add 4 wedges.

Add 4 plastinails.

Remove old cat codes and add new ones.

Issue 6 - 09/09/14 - Removed‘Anderson’ from the title so it can be used for both Anderson and Normandy.

Added 3 new cat codes for Normandy.

331/5974

357/7310

355/7354

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 48kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 1, 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

Tools required

Rule

ScissorsSquare

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Step

ladder

Electric drill

(only use

when drilling

into walls)

mm 10 20 30 40 50 60 70 80 90 100

Components - Panels

Please check you have all the panels listed below

80% x 2

90% x 1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Drawer Back (W639-124)

(639 x 124mm)

13 14

Hanging Rail (FHR660)

(660mm long)

Drawer Base (T650-367)

(650 x 367mm)

Left Side (D2356A)

(1808 x 494mm)

Top (D2355A)

(702 x 516mm)

Right Side (D2357A)

(1808 x 494mm)

Base (D2358A)

(669 x 493mm)

Horizontal (D2359A)

(669 x 493mm)

Door (D2361A)

(1559 x 345mm) x 2

Plinth (D2360A)

(669 x 80mm)

Drawer Front (D2362A)

(692 x 162mm)

Back (X1590-695)

(1590 x 695mm)

Left Drawer Side

(W370-124LH)

(370 x 124mm)

Right Drawer Side

(W370-124RH)

(370 x 124mm)

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 8

Metal dowel (F901) x 16

Handle (F847a) x 3

aJHandle Screw (F847b) x 6

Hinge (F518) x 6

Hinge plate (F523) x 6

13mm Screw (F63) x 14

13mm Screw (F79) x 1

Large locking

nut (F900) x 14

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

9mm Screw (F73) x 49mm Screw (F74) x 2

Drawer runner (F1004) x 2

Knock-in Peg (F171) x 4

Small locking

nut (F3) x 2

Rail holder

(F1014) x 2

Bracket (F327) x 1

Nail (F51) x 33

Plastic Nail (F91) x 4

Wedgefix (F639) x 4

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Step 2

Prepare the drawer

front

Screw 2 metal dowels

into the holes shown on

the back of the drawer

front .

Note: Tighten metal

dowels up fully against

the panels.

Prepare the drawer

sides

Insert a small locking

nut into the hole

shown on the left drawer

side and right drawer

side .

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Step 3

Attach the drawer

sides to the drawer

front

Push the left drawer side

. and right drawer side

. onto the back of the

drawer front .

Turn the small locking

nuts on the left

drawer side and right

drawer side .

Note: Turn the locking

nuts clockwise to

secure panels - more

than 1/2 a turn.

Small groove

Note: The locking nuts can be on

either surface of the drawer sides.

Make sure that the small groove

is on the inside, as shown.

Note: Due to the manufacturing process, the holes for the

locking nut can be on either surface of the drawer sides.

910

Assembly Instructions

Step 4

Fit the drawer base

Slide the drawer base

down the grooves in the

drawer sides and

then down into the

groove in the drawer

front .

Step 5

Fit the drawer back

between the drawer

sides and .

Make sure that the

drawer base fits into

the groove in the drawer

back .

Hold the drawer back

in position and tap the

knock-in pegs

through the holes in the

drawer sides and .

Step 6

9 10

Attach the handle

to the drawer front

using 2 screws .

J a

J b

Step 7

Fit the wedgefixes

Turn the drawer

assemblies over and

slide 2 wedgefixes

into the front and back

grooves, as shown, and

tighten up the screws.

J b

J a

Finished

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

Step 8

Finished

front edge

Prepare the left side

a: Place a runner on

the left side . Slide

back the top of runner

and use the 2nd hole

from the front to fit the

1st screw .

b: Slide the runner

back the other way and

fit the 2nd screw into

the corresponding hole

in the left side .

Screw 5 metal dowels

into the left side .

c: Tap a wooden dowel

. into the left side .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Insert 2 large locking

nuts into the left side

. .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Push a rail holder into

the left side . Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

Fit 3 hinge plates onto

the left side , making

sure that the slot is

facing towards the

finished front edge.

10mm

Assembly Instructions

Step 9

Finished

front edge

Prepare the right side

a: Place a runner on

the right side . Slide

back the top of runner

and use the 2nd hole

from the front to fit the

1st screw .

b: Slide the runner

back the other way and

fit the 2nd screw into

the corresponding hole

in the right side .

Screw 5 metal dowels

into the right side .

c: Tap a wooden dowel

. into the right side .

Insert 2 large locking

nuts into the right

side .

Push a rail holder into

the right side . Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

Fit 3 hinge plates onto

the right side , making

sure that the slot is

facing towards the

finished front edge.

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

Prepare the base and

horizontal

Tap 2 wooden dowels

into the base .

Insert 4 large locking

nuts into the base

Tap 2 wooden dowels

into the horizontal .

Insert 4 large locking

nuts into the

horizontal .

Assembly Instructions

Step 10

Prepare the left side

a: Screw 5 metal dowels

. into the holes shown

on the left side .

Note: Tighten metal

dowels up fully against

the panel.

Push a rail holder into

the hole shown. Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

b: Fit 3 hinge plates

onto the left side ,

making sure that the slot

is facing towards the

finished front edge.

Insert 2 large locking

nuts into the left side

. as shown.

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Tap a wooden dowel

into the left side as

shown.

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Finished

front edge

Finished

front edge

Join the horizontal

and base to the right

side

Push the horizontal

and base onto the

right side as shown.

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

both the horizontal

and base .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Step 11

The base has a plain

chipboard surface

plain

chipboard

surface

Assembly Instructions

Step 12

Prepare the plinth

Tap 2 wooden dowels

into the plinth .

Insert 2 large locking

nuts into the plinth

Plain chipboard

surface

Fit the plinth

Push the plinth onto

the right side .

Use a screwdriver to

tighten the large locking

nut fitted to the plinth

. .

Step 13

Fit the left side

Push the left side

onto the assembly.

Use a screwdriver to

tighten the 5 large

locking nuts fitted to

the horizontal , plinth

. and base .

Step 14

5 4

Dieses Handbuch passt für folgende Modelle

Andere Argos Inneneinrichtung Handbücher

Argos

Argos 618/0144 Bedienungsanleitung

Argos

Argos Osaka 2556868 Bedienungsanleitung

Argos

Argos 875/7276 Bedienungsanleitung

Argos

Argos 144/3556 Bedienungsanleitung

Argos

Argos Habitat 600/5779 Bedienungsanleitung

Argos

Argos 608/0811 Bedienungsanleitung

Argos

Argos 3FT Josie 436/9730 Bedienungsanleitung

Argos

Argos Camden 259/3773 Bedienungsanleitung

Argos

Argos Cheval 152/6435 Bedienungsanleitung

Argos

Argos Dalton 228/5713 Bedienungsanleitung

Argos

Argos Wow Raye Wooden Chair Bedienungsanleitung

Argos

Argos Malibu 279/6288 Bedienungsanleitung

Argos

Argos Alicia 188/8379 Bedienungsanleitung

Argos

Argos Malibu 428/3445 Bedienungsanleitung

Argos

Argos Emberton 927/5788 Bedienungsanleitung

Argos

Argos Iceland 276107 Bedienungsanleitung

Argos

Argos Atlas 157/3309 Bedienungsanleitung

Argos

Argos 487/8317 Bedienungsanleitung

Argos

Argos Matrix 609/0399 Bedienungsanleitung

Argos

Argos Wooden Filer Bedienungsanleitung

Argos

Argos Napoli 600/6259 Bedienungsanleitung

Argos

Argos Lima Bedienungsanleitung

Argos

Argos 609/0131 Bedienungsanleitung

Argos

Argos 609/2256 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung