Assa Abloy Norton SafeZone 7100SZ Series Kurzanleitung

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

Requirements:

Units are handed. Hand of unit and hand of door must be the same.

All dimensions shown in inches (mm).

Door must be hung on ball bearing butt hinges or ¾” (19) offset pivots.

Door thickness must be 1-3/4" (44) to 2-1/4" (64).

Door must swing freely through the entire opening and closing cycle before beginning the installation procedure.

Frame face must be a minimum of 2" (51).

Ceiling clearance must be a minimum of 3 -1/2" (89) for push side application or 4” (102) for pull side application. See pages

3 and 7 for templates.

Power input to unit must be of the same voltage as that stated on the unit.

Unit to be mounted on interior of building in dry environment, maximum humidity of 95%.

See NFPA70 for wiring requirements and NFPA72 for alarm system requirements.

Pull Side Applications with Slide Track

(7110SZS, 7150SZS)

(see page 7 for template)

Patent Pending

Push Side Applications with Double Lever Arms

(7120SZS, 7130SZS)

(see page 3 for template)

Item No. Description

1 Track (Pull Side)

2 Cover

3 Track Arm (Pull Side)

4 Double Lever Arm (Push Side)

• Allen wrench set (inch)

• Flat blade screwdriver (potentiometer & terminal size)

• Screwdriver (Phillips size 2)

• Tape rule

• Power drill

• Center punch

• Wire stripper

Tools required:

Use screw pack and hardware provided to mount operator.

Table of Contents:

General Information...................2

Push Side Template...................3

Push Side Installation..............3-5

Closer Adjustments...................6

Pull Side Template.....................7

Pull Side Installation.................7-9

Closer Adjustments...................10

Electrical Connections...............11

Selective Hold Open..................12

Sensor Info and Set-up.........13-14

Troubleshooting.........................14

312

7100SZ Series SafeZone

With Selective Hold Open Option

Installation and Instruction Manual

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

General Information

Certifications

UL228, UL10B

Included with 7110SZS and 7150SZS Included with 7120SZS and 7130SZS

7120 Arm

Assembly

(7701-1A)

7130 Arm

Assembly

(7701-1B)

Arm Screw

(7701-MAS)

Track End

Cap (2)

Slide Assembly

(7100SLD)

Track Cover

7110 Main Arm (7110-1A)

Slide Track

(7100-1T)

7150 Main Arm, Handed

(7150-1L: Left Hand

7150-1R: Right Hand)

Track Mtg

Screw (2)

Cushion Stop

Assembly

(7100CB)

NOTE: Optional remote

for Advanced Settings

(sensitivity, door control

mode) if required.

(7100REM)

9/32” (7 mm) thru;

3/8” (9.5 mm) dia. x

3/8” (9.5 mm) deep on

door opposite to closer

Standard

Optional Through-bolts and

grommet-nuts All

Preparation for Fasteners

Door or Frame

Fasteners Drill-Sizes

1/4” - 20 machine

screw Metal

Pre-Drill: 9/64 hole

Sleeve nuts and

bolts

(Shoe screws only)

Hollow

Metal

9/32” (7 mm) through;

3/8” (9.5 mm) door face

opposite to closer

Aluminum

or Wood 3/8” (9.5 mm) through

Self drilling screw

(Track screws only)

Drill: #7 (0.201” dia.)

Tap: 1/4” - 20

Metal

Self drilling screw

(Closer mounting

screws only)

Metal

Pre-Drill: 3/16 hole

Component Layout

Cover

LH = 7100CL

RH = 7100CR

Closer/Holder Unit Assembly

Backplate

Sensor

Power Supply

(120V units only)

Backplate

Mtg Screw (4)

Cover Mtg

Screw (6)

Test/Power

Switch

Selective

Hold Open

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

7120SZS, 7130SZS: Double Lever Arm (Push Side)

Operator Mounting

Prepare Frame

Right Hand Reverse - RHR

LHR - Left Hand Reverse

Ceiling Line

(51)

3-1/2

(89)

Min

Use of an auxiliary door stop, by

others, is required for these applications.

Left Hand Door - LH

RH - Right Hand Door

Hinge

Edge

Door

Hinge or Pivot

Drill #7; Tap 1/4-20 19-3/4

1-3/4

(44.5)

1-5/8

(41.3)

(101.6)

11-1/4

(285.8)

(501.7)

For Concealed

Wiring Only

7/8

(22.2) DIA THRU

11/16

(17.5)

5/16

(7.9)

Left hand door shown, right

hand opposite.

All dimensions shown in

inches (mm).

Install two screws in

the key slot locations

leaving 1/8" gap

between screw head

and frame as shown

(a).

1/8"

Top of

Door

Frame

Soffit

1-3/4

(44.5)

7/8

(22.2)

Frame

Model

Door Open

Angle

Dim “A”

Dim “B”

Reveal

Inches

(mm)

Inches

(mm)

712X SZ

100° Max.

5-7/8

149.2

13-3/8

339.7

2-3/4” - 7”

180° Max.

3-1/8

79.4

10-5/8

269.9

2-3/4 - 4”

165° Max.

4” - 7”

713X SZ

180° Max.

4” - 7”

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

Operator Mounting

Hang closer body

by key hole slots (b)

and slide closer

toward hinge to

capture screw

heads (c).

Operator Mounting

Install remaining

mounting screws

through back plate and

tighten all four screws

(d). Pull wiring through

holes (if concealed

wired).

Arm Shoe Mounting

Mount closer arm shoe to

door face as shown.

For Concealed Wired Only

(If surface wired, see page 11)

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

Attach Arm

Preload Closer Spring

Arm Screw

(7/16” Drive)

Main

Arm

Closer Spring Adjustment

11/16"

Wrench

Closing Force

Weaker

Stronger

Pinion

Flat

Arm

Mark

Align the pinion flat with

the letter "S".

Slowly increase closer power

until door closes consistently.

NOTE: A closer set to the ADA

required 5 lbs opening force

may not be strong enough to

close the door due to latching

hardware, air pressure, or

frame issues.

90°

With the door closed and

latched, rotate main arm until

secondary arm is perpendicular

to the door frame, then tighten

adjustment screw as shown with

7/16” wrench.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

Closer Adjustments

1/8"

Hex

Key

"B"

Backcheck

75°

1/8"

Hex

Key

"P"

Backcheck

Position

75°

90°

Electrical Connections / Selective Hold Open Adjustments

Attach Cover

311

Attach cover using screws provided.

Never Close

backcheck valve

completely

Do not remove valves

from closer. Hydraulic

oil will escape.

Weaker

Stronger

Closing Speed Controls

• Valve "S" Controls Sweep Range from

full open to 5°.

• Valve "L" Controls Latch Range from 5°

to closed.

Opening Cycle

• Valve "B" controls the strength of

cushioning in Backcheck Range.

NEVER close this valve completely – it

is not to provide a positive stop.

• Valve "P" adjusts the angle that back-

check is felt in the open cycle.

Electrical Connections Page 11

Selective Hold Open Adjustments Page 12

"S"

Sweep

5°

1/8"

Hex

Key

"L"

Latch

0°

5°

1/8"

Hex

Key

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

7110SZS, 7150SZS: Track Mount (Pull Side)

Operator Mounting

Prepare Frame

Ceiling Line

(51)

(102)

Min

Left Hand Door - LH

Right Hand Reverse - RHR

RH - Right Hand Door

LHR - Left Hand Reverse

Track Mount Unit

(152.4)

19-1/8

(485.8)

CHinge or Pivot

3-1/4

(82.6)

3/4

(19)

For Concealed

Wiring Only

7/8

(22.2) DIA THRU

1-3/8

(34.9)

1-1/16

(27)

14-1/2

(368.3)

(584.2)

1-1/4 (31.8)

7110SZ Standard Arm

7150SZ Double Egress Arm

Series Dim "A"

5/8 (15.9)

Right hand door shown, left

hand opposite.

All dimensions shown in

inches (mm).

Install two screws in

the key slot locations

leaving 1/8" gap

between screw head

and frame as shown

(a).

1/8"

1/8

(3.2)

Top of

Door

Frame

Soffit

9/64 (3.6) Holes

for track screws

(44.5)

1-3/4

7/8

(22.2)

*9/64 (3.6) Holes

for track screws*

Prepare holes for mounting per instructions on page 2. *Track screws are

self tapping and are smaller than closer mounting screws*

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

Arm Mounting

Fully close Latch & Sweep

Valves with 1/8" wrench

provided.

Mount closer arm to pinion square as shown.

Use main arm to rotate pinion

until flat is visible.

RE-INSTALL

HERE

LEFT

HAND

RIGHT

HAND

PINION

FLAT

LEFT

HAND

RIGHT

HAND

Align the pinion flat as

shown.

*All views from floor looking upward*

Attach arm with provided

screw and washer.

Tighten arm screw with

5/32" Allen wrench.

Attach Arm

Hang closer body

by key hole slots (b)

and slide closer

toward hinge to

capture screw

heads (c).

Operator Mounting

Install remaining

mounting screws

through back plate

and tighten all four

screws (d). Pull

wiring through holes

(if concealed wired).

CFor Concealed Wired Only

(If surface wired, see page 11)

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

1) Insert slider into track.

2) Insert spring cushion stop on hinge side

of track for 125°or less opening angle.

!Do not use for openings greater

than 125°!

3) Insert end caps (both ends).

4) Secure track to door using provided

screws.

5) Snap on cover.

Set Screws

toward hinge

If opening angle greater than 125°, spring cushion stop cannot be used and an auxiliary stop

by others is required.

Mount Track

Connect Arm to Track

Open door to maximum desired

swing minus 5° and hold. Slide

spring cushion stop assembly

against slider assembly and

secure to track using 5/64" or

2mm wrench.

HINGE

Secure arm to slider

assembly using 3/16"

Wrench. Turn wrench

counterclockwise to

tighten.

Open Latch & Sweep Valves

with 1/8" wrench provided.

Closer Spring Adjustment

11/16"

Wrench

Closing Force

Weaker

Stronger

Slowly increase closer power

until door closes consistently.

NOTE: A closer set to the ADA

required 5 lbs opening force

may not be strong enough to

close the door due to latching

hardware, air pressure, or

frame issues.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9371-0085-020 (01-14)

ASSA ABLOY

Closer Adjustments

1/8"

Hex

Key

"B"

Backcheck

75°

1/8"

Hex

Key

"P"

Backcheck

Position

75°

90°

Electrical Connections

Attach Cover

312

Attach cover using screws provided.

Never Close

backcheck valve

completely

Do not remove valves

from closer. Hydraulic

oil will escape.

Weaker

Stronger

Closing Speed Controls

• Valve "S" Controls Sweep Range from

full open to 5°.

• Valve "L" Controls Latch Range from 5°

to closed.

Opening Cycle

• Valve "B" controls the strength of

cushioning in Backcheck Range.

NEVER close this valve completely – it

is not to provide a positive stop.

• Valve "P" adjusts the angle that back-

check is felt in the open cycle.

Electrical Connections Page 11

Selective Hold Open Adjustments Page 12

"L"

Latch

0°

5°

1/8"

Hex

Key

"S"

Sweep

5°

1/8"

Hex

Key

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Corbin Russwin DC8210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130-HU Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 3828 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Crawford MCS-R Bedienungsanleitung

Assa Abloy

Assa Abloy Rixson Smok-Chek VI Kurzanleitung

Assa Abloy

Assa Abloy RIXSON SMOK-CHEK V 0101 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9540 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC340 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1331 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED8200A Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5400 FE Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 1105 Bedienungsanleitung

Assa Abloy

Assa Abloy 78PRA-8L Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton LEO 5700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 2409 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5200 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7200 Series Kurzanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy besam PUSH-N-GO Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung