Assa Abloy Norton 7540ST Series Bedienungsanleitung

Copyright © 1997, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-0551-020 (05-14)

ASSA ABLOY

Hinge Edge of Door

Left Hand Door-LHRight Hand Reverse-RHRRight Hand Door-RHLeft Hand Reverse-LHR

Hinge Edge of Door

Right Hand Door-RHLeft hand Reverse-LHRLeft Hand Door-LHRight Hand Reverse-RHRPush (Stop) Side MountedPull (Hinge) Side MountedInstallation Type• With or without "DA" suffix, delayed action closing feature.• With or without "M" suffix, Metal Cover.Non Hold Open Models Installation Instructions • Maximum pull side frame reveal is 1/8" (3mm).• Minimum frame face for pull side is 1-1/8" (26.6mm).• All components are non handed.• The use of ball bearing hinges is recommended for the door on which the closer will be installed. Door must swing freely.• Where severe or abusive conditions are expected a separate door stop, supplied by others, is recommended to assist in preventing damage to the door closer, closer arm; or to the door, frame or adjacent walls.• Door and frame must be properly reinforced, or the use of special fasteners employed, to prevent door collapse or the mounting screws from pulling out.• All dimensions are given in inches with corresponding metric dimensions (millimeters) in parentheses.Note: For Special Applications a separate door and frame preparation template is packed with these instructions. Use this sheet for installation sequence and closer adjustments only.• Sized Door Closers 7740 have 50% power increase capability. Closer size 2 has the weakest power, closer size 6 has the strongest power.• Multi-Sized Closer 7540 can be adjusted from size 1 thru 6.Series 7540ST, 7740ST (Pull Side Mounted)Series PS7540ST, PS7740ST (Push Side Mounted) Door Closers with Slide Track InstallationsAn incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility of misapplication or misadjustment.CAUTIONFor Use on Doors with 4½" or 5" Wide Butt Hinges

ASSA ABLOY

Track Assembly

End Cap (2)SliderCushion BlockStop BlockChannel

Non Hold Open Assembly PackBox No. 40-7940-0050-000

Template• Drop Plate and sex nuts not shownScrew packStop Position ScrewStudHingeSpring tube Plastic Cover (standard)(1)1/4-20 x 5/8 lg. phillip drive & arm washer with thread lock (1)1/4-20 x 5/8 lg.trusshead phillip drivewith thread lock(4)1/4-20 x 2-1/4 lg.phillip drive(2)1/4-20 x 1-1/2 lg. phillip drive1122Pull Side Installation

Pull Side

8-32 x 1/4 lg.phillip drive

CLHinge

2-11/16(68.3)24-3/16(614.4)(19)3/4

(2) Fastener holes in frame for track

(4) Fastener holes in door for closer13/16(20.6)

3/4(19)2-3/8(60.3)5-7/8(149.2)6-3/4(171.5)44-3/812-3/8(101.6)(111.1)(314.3)

Metal Cover(optional)(2)3rd hole Arm RodArm Tube

(4) Fastener holes in door for 7786 drop plate

inches (mm)

• Maximum door opening: 110°- recommended with cushion stop in track. 180°- without cushion stop.• Use of auxiliary door stop may be required to prevent damage to door, frame, and hinge. • Dimensions are given in Notes:• Right hand door is shown.• Do not scale drawing.• Minimum door width 26" (660.4mm).• .1046 (2.7mm) minimum thickness recommended for hollow metal door and frame reinforcement.• From centerline of hinge to end of track 27-3/8" (695.3mm).• Minimum ceiling clearance for track is 1-1/8" (26.6mm).• Closer mounted with sex nuts requires the use of door silencers.

8-32 x 1/4 lghex socket capscrew with thread lockCounterborefacing upInsertCover Screw(2 Per Cover)

ASSA ABLOY

3• Track Assembly Remove slider assembly parts from box # 40-7940-0050-000 and insert into channel in the order shown. See illustration on page 2 or 4. Use of a hold open device or assembly will void the UL® listing for this product. Insert end caps into ends of track prior to installing.• Install track to frame. Place the assembled slide track against frame with the open side down, stop and cushion blocks toward the hinge. Move the slider to the opposite end of the slide track. Secure slide track with 1/4-20 flat head phillips drive mounting screws.• Connect arm to track. Open door approximately 5"(127mm), rotate arm to slider and place end on stud. Push down on arm and tap gently to seat (to prevent stud from turning during assembly). Secure with 1/4-20 x 5/8" long truss (rounded) head phillips drive screw with thread lock. CAUTION: Closer arm is under spring tension and may be difficult to rotate.• Set door stop angle. Open door to the angle you want the door to stop. With the door held at that location, slide stop with cushion block against slider. Tighten the stop position screw (large set screw) with 3/16" hex wrench (from screw pack) until secure. Release door.• Adjust closer (see page 5) before installing cover. • Install Cover. Slide insert into cover slot (see illustration). Fasten cover to closer with (2) 8-32 x 1/4" long round head phillips drive screws. Installation Sequence Pull or Push Side Mount• Determine hand of door and type of installation from illustrations on page 1. • Use template dimensions to locate fastener holes on door and frame. See "Preparation for Fasteners" chart below. Frame: Prepare the frame for mounting track. Drill and tap holes for 1/4-20 machine screws or #14 wood screws. Door: Prepare the door for mounting closer. Drill and tap (4) holes for 1/4-20 machine screws, #14 wood screws, 3/8 diameter sex-nuts, or through bolts and grommet-nuts. Note: If drop plate is used, prepare holes for 7786 drop plate instead of closer. Secure drop plate before mounting closer. • Fasten closer to door or drop plate. Position spring tube away from hinge. See arm indexing illustrations (above right) for valve positioning (up or down). Secure mounting screws.• Assemble Slide Arm. Insert flat arm rod into arm tube with the counterbore screw hole facing up. Align counterbore with the 3rd hole in the arm tube and secure with 8-32 x 1/4 long hex socket cap screw. See illustration on page 2 or 4.• Install arm on closer pinion see arm indexing illustrations (above right). Position slide arm with counterbore facing up and align with pinion flat as illustrated. Install onto pinion. Secure with washer and flat head phillips drive arm screw with thread lock.

Arm in position

Left handRight handPinion Flat

Arm Indexing

Valves downValves upPULL MOUNT

Arm in position(Bottom View)

Right handPinion FlatArm IndexingLeft handValves downValves upPUSH MOUNT

(Top View)

Aluminum orWood Preparation for FastenersFasteners Door or Frame Drill Sizes#14 type "A" S.M. screw Wood7/32" (5.56mm)Arm: 1-1/4" (32mm)Closer: 2-3/4" (70mm) 1/4" -20 machine Metaldrill: #7 (.201")screw tap: 1/4" -20Sex-nuts and bolts Hollow Metal9/32" (7.00mm) through3/8" (9.50mm) door-faceopposite to closer3/8" (9.50mm) throughThrough-bolts and 9/32" (7.00mm) through;grommet-nuts All3/8" (9.50mm) dia. x3/8" (10mm) deep door-face opposite to closer(Optional)

ASSA ABLOY

412End Cap (2)SliderStudCushion BlockStop Block

Non Hold Open Assembly PackBox No. 40-7940-0050-000

Stop Position Screw

Track Assembly

Channel• Drop Plate and sex nuts not shown

Push Side

12Screw pack(4)1/4-20 x 5/8" lg. phillips drive(1)1/4-20 x 5/8 lg. truss headphillips drivewith thread lock(1)1/4-20 x 5/8 lg. phillips drive & arm washer with thread lockPlasticCover(standard)Spring TubeTemplatePush Side Installation(4)1/4-20 x 2-1/4 lg.phillips drive

CLCLHinge

(4) Fastener holes in door for closer1-7/8(47.6)

3/4(19)2-3/8(60.3)6-3/8(162)6-3/4(171.5)44-3/812-3/8(101.6)(111.1)(314.3)

Bottom of frame stop3/4(19)(4) Fastener holes in frame for track4- 3/16(106.4)8(203.2)1422(355.6)(558.8)HingeDoorFrameViewed from TopMetal Cover(optional)(2)8-32 x 1/4 lg.phillips drive 3rd hole 8-32 x 1/4 lghex socket capscrew with thread lockCounterborefacing upArmRodArmTubeInsert

(4) Fastener holes in door for 7786 drop plate

• Left hand door shown.• Do not scale drawing.• Minimum door width 29" (736.6mm).• Maximum door opening: 120°.• Use of auxilary door stop may be required for openings to 120°, to prevent damage to door, frame, and hinge.inches(mm)Notes:• .1046 (2.7mm) minimum thickness recommended for hollow metal door and frame reinforcement.• From centerline of hinge to end of track is 27-11/16" (703.3mm)• Dimensions are given inCover Screw(2) per cover

ASSA ABLOY

5Closer AdjustmentsClosing Power Control Figure 1Delayed ActionBackcheckSweepLatchClosing ControlsOpening ControlsClosing Power 7740 Models come in five different sizes (2 through 6); each power size can be increased by 50%. Adjust as required. See Figure 1. 7540 Models are fully adjustable. For proper sizing see Power Adjustment Chart. To adjust closer power, see Figure 1. Increase or decrease power as necessary. Closing Cycle (see illustrations above). Valve "L" controls door speed in Latch Range. Valve "S" (optional) Delayed Action Closer only. Controls door speed in Sweep Range. Valve "SD" controls door speed in Sweep Range for Standard Closer or Delay Range for Delayed Action Closer Use 1/8" hex-key furnished and adjust all valves as shown in Figure 2.Attention: Adjust closing speed to between 4 to 7 seconds from 90°. Use of door by handicapped, elderly or small children may require greater closing time.Opening Cycle (see illustration above). Valve "B" cushions (slows) door opening in the Backcheck Range. NOTE: Never close this valve completely or damage to closer may occur. Valve "P" allows "backcheck" to begin later in the opening cycle when required. Closing Speed ControlsFigure 2"L" (Latch)"S" (Sweep) Only supplied with Delayed Action Feature"S/D" (Delay Range)"B" (Backcheck)-NEVER close completely"B" (Backcheck)-NEVER close completely"P" (Normally shipped closed)slowerfasterstrongerweakerCaution:Do not back valves outof closer or a leak willresult.Standard CloserOnlyDelayed ActionCloser OnlyOR"S/D" (Sweep Range)"P" (Normally shipped closed)"L" (Latch) 1/8" Hex Key

3000 Highway 74 East • Monroe, NC 28112Tel: (877)- • Fax: (800)-338-0965974-2255www.nortondoorcontrols.com

ASSA ABLOY

Install closer per instructionswith the proper pre-load applied to the arm then adjust spring power. The power adjustment will notwork properly if the closerspring is not pre-loaded.To increase power, use 11/16"wrench to turn poweradjustment nut clockwise.To decrease power, turn nutcounter clockwise. DO NOT use a power drill or driver to turn adjustment nut. This will damage closer and void warranty."Spring PowerAdjustment Nut"+

NOTE: Maximum of 15 turns (360°) of Power Adjustment Nut. Closer is shipped set at lowest power setting.Power Adjustment Chart Full Clockwise Turns of Closer Power Adjustment NutInterior DoorExterior Door0 2255Door Size Inches (mm)28-32(0.07-0.80)37-42(0.95-1.05)43-48(1.10-1.20)33-36(0.85-0.90)88117540STPS7540ST

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Yale 3000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC200 Bedienungsanleitung

Assa Abloy

Assa Abloy RD3 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4600 A Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 724 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Rixson Smok-Chek VI Kurzanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Kurzanleitung

Assa Abloy

Assa Abloy Norton 5700P Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC3210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600H Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FIREGUARD 12-2468 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW60 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 2500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW300 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600H Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5400 FE Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Electroguard-59 80 Series Montageanleitung

Assa Abloy

Assa Abloy G-CO-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung