B-K lighting TETON Bedienungsanleitung

Hot SurfaceLow VoltageWarning

RELEASE DATE

10/25/2022

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL

ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

REFERENCE NUMBER

INS-2815-00

RELEASE DATE

08/02/2023

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS001156

Installation Instruction

TETON

LED

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

INSTRUCTIONS

Flammable

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local and

Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective

equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and

lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause an

unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part, as

this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body.

• Replace LED assembly only with correct wattage and type of

power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause an

unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before

replacing lamp/LED. Fixture gets HOT quickly!

Contact only switch/plug when turning on.

Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time.

Use a soft cloth or gloves. Oil from skin may cause

damage.

SAVE THESE INSTRUCTIONS

· Suitable for wet locations

IMPORTANT LISTINGS AND CERTIFICATIONS

1/8” Allen Wrench

Phillips Screwdriver

Waterproof Wire Connectors

TOOLS

NEEDED:

Please refer to the low voltage design guide at www.bklighting.com/lvguide before installation for proper wire selection.

TT - Teton Fixture

Universal Mounting Ring

RELEASE DATE

10/25/2022

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS-2815-00

RELEASE DATE

08/02/2023

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS001156

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Phase 2 - Finish Installation of Fixture with Remote Transformer

Installation Instruction

TETON

LED

1. Install universal mounting ring (supplied with

fixture) using #10-24 screws onto back box. Align

fixture mounting holes to final mounting position.

Universal mounting ring orientation determines

fixture orientation.

2. Make watertight connections from remote

transformer to fixture leads using waterproof wire

connectors (not included). See wiring diagram.

Phase 1 - Rough In

Installation of Back box

1. Install conduit (not included) to be used

with this product.

2. Install junction box so that front face

is flush with finished wall. Seal building

envelope as per NEC.

3. Connect box to conduit and pull wires for

connections (See Wiring diagram).

Additional Info

• Please follow National and Local electrical codes for your area.

• 4” round cast box.

• Suitable for through wire.

• Suitable for installation into combustible materials.

• Rated for 90° C.

• Junction box, universal mounting ring screws, box mounting

hardware and gaskets (not included).

3. Using a 1/8” allen wrench mount fixture using

two (2) #10-24 screws to installed back box.

Seal building envelope as per NEC. Do not

overtighten.

HOT12V

FIXTURE

NEUTRAL

Remote

Magnetic

Transformer

12v

WIRING DIAGRAM

LED - For use with 12VAC LED remote

transformer or magnetic transformers only. B-K

Lighting cannot guarantee performance with

third party manufacturers’ transformers.

Low Voltage - For use with 12VAC remote

transformer.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Replacing LED Board/Driver and Optics

Replacing Low Voltage LED Lamps

RELEASE DATE

08/02/2023

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS001156.1

1. Use a 5/64” allen wrench to loosen #8-32 stainless

set screw and remove cap.

2. Space three fingers evenly around the optic and

gently rock optic to remove.

4. Disengage LED board and driver assembly. Replace

with new board and driver assembly.

5. Reverse install LED board and driver by carefully

wrapping 18 gauge wires around driver and

inserting into fixture body. Secure LED board in

place with stainless steel screws.

6. Snap optics in place. Place cap on fixture and

tighten set screw.

3. Use a 5/64” allen wrench to remove two (2) #2-56

socket head cap screws on LED board, grasp

LED board and gently pull up to expose quick

disconnect.

7. Use a 5/64” allen wrench on #8-32 stainless set

screw to secure cap.

1. Use a 5/64” allen wrench to loosen #8-32 stainless

set screw and remove cap.

3. Place cap on fixture and tighten set screw. Tighten

screw to 1/2 inch pounds. Top of screw should sit

flush with fixture cap.

Warning: Do not over tighten set screw. Doing

so will compromise o-ring seal and will void

warranty.

2. Firmly insert lamp pins into socket to make

connection. Rocking motion maybe required.

Do not exceed the maximum wattage listed on

the fixture label before installing.

Replacement/Installation Instructions

TETON

LED/LOW VOLTAGE LED LAMP

Andere B-K lighting Beleuchtungsausrüstung Handbücher

B-K lighting

B-K lighting MB2 Bedienungsanleitung

B-K lighting

B-K lighting Mini-Micro Series Bedienungsanleitung

B-K lighting

B-K lighting Union Bollard Bedienungsanleitung

B-K lighting

B-K lighting ORION Bedienungsanleitung

B-K lighting

B-K lighting Denali Series Bedienungsanleitung

B-K lighting

B-K lighting Altair Bedienungsanleitung

B-K lighting

B-K lighting RE1 Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Remote Bedienungsanleitung

B-K lighting

B-K lighting ORION Bedienungsanleitung

B-K lighting

B-K lighting MICRO NITE STAR Bedienungsanleitung

B-K lighting

B-K lighting MINI-MICRO RECESSED UPLIGHT Bedienungsanleitung

B-K lighting

B-K lighting HP2RM Bedienungsanleitung

B-K lighting

B-K lighting Union Bollard Bedienungsanleitung

B-K lighting

B-K lighting SS Bedienungsanleitung

B-K lighting

B-K lighting BKSSL Precision2 DR2 Series Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Series Bedienungsanleitung

B-K lighting

B-K lighting Nite Star Bedienungsanleitung

B-K lighting

B-K lighting YOSEMITE Series Bedienungsanleitung

B-K lighting

B-K lighting BACK BOX Bedienungsanleitung

B-K lighting

B-K lighting INTEGRAL DENALI Series Bedienungsanleitung

B-K lighting

B-K lighting SQUARE ADJUSTABLE WELL STAR Bedienungsanleitung

B-K lighting

B-K lighting Path Star Bedienungsanleitung

B-K lighting

B-K lighting PS Bedienungsanleitung

B-K lighting

B-K lighting LT Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung