B-K lighting ArtiStar Integral Bedienungsanleitung

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

INSTRUCTIONS

RELEASE DATE

11/03/2021

REFERENCE NUMBER

INS-2119-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR

SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

TOOLS

NEEDED:

Warning High Voltage Hot Surface

· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground

IMPORTANT LISTINGS AND CERTIFICATIONS

ArtiStar Integral

Solid State LED

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local

and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective

equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and

lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause

an unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part,

as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body.

• Replace LED assembly only with correct wattage and type

of power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause

an unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT

SAFETY INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before

replacing lamp/LED. Fixture gets HOT quickly!

Contact only switch/plug when turning

on. Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time.

Use a soft cloth or gloves. Oil from skin may cause

damage.

SAVE THESE INSTRUCTIONS

Standard Installation

Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.

3/16” and 5/64” Allen Wrench

Waterproof Wire Connectors

Drill Bit and Drill

Mounting Hardware

Standard Mount

Anchor Base

Cap

Integral Driver

Housing

ArtiStar Knuckle

Mounting System

RELEASE DATE

11/03/2021

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

REFERENCE NUMBER

INS-2119-00

ArtiStar Integral

Solid State LED

Standard Installation

5. Make watertight connections using waterproof

wire connectors (not included) to connect

primary branch circuit wiring to primary driver

side. Connect incoming ground to ground wire

provided in fixture body. See wiring diagram.

WIRING DIAGRAM

7. Use a 3/16” allen wrench to slightly loosen ¼”-28

stainless steel black oxide socket head cap screw

at the knuckle for vertical aiming purposes.

Rotate fixture at base and aim fixture to desired

horizontal location.

8. Tighten the three (3) #8-32 stainless steel set

screws on anchor base and ¼”-28 stainless steel

locking screw at the knuckle to secure all aiming

positions.

6. Place fixture onto mounted anchor base and

press straight down until the two pieces are flush

with each other.

1. Study anchor base plan. Prepare mounting

surface for anchor base.

2. Use a 5/64” allen wrench to loosen three (3)

#8-32 stainless steel set screws (do not remove

stainless steel set screws from fixture base).

Remove anchor base from bottom of fixture.

3. Pull branch circuit wiring necessary for

installation (not included). Feed branch circuit

wiring through anchor base.

4. Secure anchor base to solid surface (i.e. wood,

concrete) using appropriate hardware for specific

surface.

Seal base to surface as per NEC.

Fixture Installation

All line voltage connections must be made in

compliance with the National Electrical Code.

Failure to do so will void warranty.

HOT (+)

FIXTURE

NEUTRAL

DRIVER

(-)

GROUND GROUND IN HOUSING

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

INSTRUCTIONS

RELEASE DATE

11/03/2021

REFERENCE NUMBER

INS-2120-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR

SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

TOOLS

NEEDED:

Warning High Voltage Hot Surface

· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground

IMPORTANT LISTINGS AND CERTIFICATIONS

ArtiStar Integral

Solid State LED

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local

and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective

equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and

lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause

an unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part,

as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body.

• Replace LED assembly only with correct wattage and type

of power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause

an unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT

SAFETY INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before

replacing lamp/LED. Fixture gets HOT quickly!

Contact only switch/plug when turning

on. Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time.

Use a soft cloth or gloves. Oil from skin may cause

damage.

SAVE THESE INSTRUCTIONS

Standard Installation

Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.

Stability Flange

Power Pipe

ArtiStar Knuckle Mounting

System

Integral Driver

Housing

3/16” and 5/64” Allen Wrench

Waterproof Wire Connectors

Phillips Screwdriver

RELEASE DATE

11/03/2021

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

REFERENCE NUMBER

INS-2120-00

ArtiStar Integral

Solid State LED

Standard Installation

Power Pipe Mounting Option

Finished grade

Pea gravel or sand

Finished grade

Concrete

Finished grade

Stability Flange

Pea gravel or sand

Finished grade

Pea gravel

or sand

Above Ground

Installation

Pea gravel

or sand

Concrete

Pea gravel

or sand

Pea gravel

or sand

Pea gravel

or sand

Concrete

Below Ground

Installation

Pea gravel

or sand

4. Back fill with pea gravel or sand prior to pour.

8. Tighten three (3) #8-32 stainless steel round

head Phillips screws at base and 1/4”-28

stainless steel black oxide socket head screw

at the knuckle to secure all aiming positions.

Finished grade

Pea gravel or sand

Finished grade

Concrete

Finished grade

Stability Flange Pea gravel or sand

Finished grade

Pea gravel

or sand

Above Ground

Installation

Pea gravel

or sand

Concrete

Pea gravel

or sand

Pea gravel

or sand

Pea gravel

or sand

Concrete

Below Ground

Installation

Pea gravel

or sand

5. Pour concrete (not included).

Label on Power Pipe™ indicates installation

depth with finished grade.

WIRING DIAGRAM

6. Use waterproof wire connectors (not included)

to connect driver primary leads to branch

circuit wires. Connect incoming ground to

ground wire provided in fixture body. See

wiring diagram.

7. Insert wires, connectors and driver into fixture

base and attach to Power Pipe™. To aim

fixture, use 3/16” Allen wrench to slightly

loosen ¼”-28 stainless steel black oxide

socket head screw at the knuckle for vertical

aiming purposes. Rotate fixture to aim to

desired horizontal location.

Finished grade

Pea gravel or sand

Finished grade

Concrete

Finished grade

Stability Flange Pea gravel or sand

Finished grade

Pea gravel

or sand

Above Ground

Installation

Pea gravel

or sand

Concrete

Pea gravel

or sand

Pea gravel

or sand

Pea gravel

or sand

Concrete

Below Ground

Installation

Pea gravel

or sand

3. Pull branch circuit wires necessary for

installation (not included) through Power Pipe.

Allow for additional cable to make connections

to fixture lead and future service. Place Power

Pipe in hole. Do not cut PVC.

Finished grade

Pea gravel or sand

Finished grade

Concrete

Finished grade

Stability Flange

Pea gravel or sand

Finished grade

Pea gravel

or sand

Above Ground

Installation

Pea gravel

or sand

Concrete

Pea gravel

or sand

Pea gravel

or sand

Pea gravel

or sand

Concrete

Below Ground

Installation

Pea gravel

or sand

Pea gravel or sand

Finished grade

Pea gravel or sand

Concrete or Soil

Finished grade

LINE 12V

FIXTURE

COM

Remote

Transformer

(by others)

COM

Finished grade Optional

Stability Flange

2. Slide optional Stability Flange onto Power

Pipe. Use optional Stability Flange to aid in

installation of Power Pipe.

1. Excavate trench according to designed

lighting plan. Dig hole a minimum of 18” deep

and 10” wide to accommodate Power Pipe at

desired fixture location(s).

All line voltage connections must be made

in compliance with the National Electrical

Code. Failure to do so will void warranty.

HOT (+)

FIXTURE

NEUTRAL

DRIVER

(-)

GROUND GROUND IN HOUSING

DRIVER HOUSING MUST BE INSTALLED ABOVE GRADE. POWER PIPE™ IS LABELED AT GRADE LEVEL.

DRIVER HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

INSTRUCTIONS

RELEASE DATE

11/03/2021

REFERENCE NUMBER

INS-2121-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR

SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

TOOLS

NEEDED: 3/16”, 1/8” and 5/64” Allen Wrench

Waterproof Wire Connectors

Mounting Hardware

Warning High Voltage Hot Surface

· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground

IMPORTANT LISTINGS AND CERTIFICATIONS

ArtiStar Integral

Solid State LED

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local

and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective

equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and

lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause

an unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part,

as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body.

• Replace LED assembly only with correct wattage and type

of power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause

an unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT

SAFETY INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before

replacing lamp/LED. Fixture gets HOT quickly!

Contact only switch/plug when turning

on. Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time.

Use a soft cloth or gloves. Oil from skin may cause

damage.

SAVE THESE INSTRUCTIONS

Junction Box

(Not Included)

Universal Mounting Ring Canopy

ArtiStar Knuckle

Mounting System

Integral Driver

Housing

Standard Installation

WIRING DIAGRAM

3. Use a 1/8” allen wrench to mount fixture with

two (2) #10-24 hex screws to installed back

box. Do not over tighten.

Phase 2 - Finish Installation of Fixture.

1. Install universal mounting ring (supplied with

fixture) using appropriate mounting hardware

(By Others). Align fixture mounting holes to

final mounting position.

2. Pull branch circuit wires necessary for

installation (not included). Use waterproof

wire connectors (not included) to connect

driver primary leads to branch circuit wires.

Connect incoming ground to ground wire

provided in fixture body. See wiring diagram.

4. Use a 3/16” allen wrench to slightly loosen

¼”-28 stainless steel black oxide socket head

cap screw at the knuckle for vertical aiming

purposes. Use a 5/64” allen wrench to loosen

the three (3) #8-32 stainless steel set screws.

Rotate to aim fixture to desired horizontal

location.

5. Tighten the three (3) #8-32 stainless steel

set screws and 1/4”-28 stainless steel black

oxide socket head cap screw at the knuckle to

secure all aiming positions.

Phase 1 - Rough In

Installation of Back box

1. Install Conduit (not included) to be used with this

product.

2. Install junction box so that front

face is flush with finished wall or

ceiling.

3. Connect box to conduit and pull wires for

connections (See Wiring Diagram).

Additional Info

• Please follow National and Local electrical codes for your area.

• Suitable for through wire.

• Suitable for installation into combustible materials.

• Rated for 90° C.

• Junction box, universal mounting ring screws, box mounting

hardware and gaskets (not included).

All line voltage connections must be made

in compliance with the National Electrical

Code. Failure to do so will void warranty.

HOT (+)

FIXTURE

NEUTRAL

DRIVER

(-)

GROUND GROUND IN HOUSING

RELEASE DATE

11/03/2021

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

REFERENCE NUMBER

INS-2121-00

ArtiStar Integral

Solid State LED

Standard Installation

Andere Handbücher für ArtiStar Integral

Inhaltsverzeichnis

Andere B-K lighting Beleuchtungsausrüstung Handbücher

B-K lighting

B-K lighting Union Bollard Bedienungsanleitung

B-K lighting

B-K lighting HP2RM Bedienungsanleitung

B-K lighting

B-K lighting ORION Bedienungsanleitung

B-K lighting

B-K lighting DENALI Bedienungsanleitung

B-K lighting

B-K lighting Nite Star Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Remote Bedienungsanleitung

B-K lighting

B-K lighting MICRO NITE STAR Bedienungsanleitung

B-K lighting

B-K lighting Path Star Bedienungsanleitung

B-K lighting

B-K lighting TETON Bedienungsanleitung

B-K lighting

B-K lighting YOSEMITE Series Bedienungsanleitung

B-K lighting

B-K lighting SS Bedienungsanleitung

B-K lighting

B-K lighting BACK BOX Bedienungsanleitung

B-K lighting

B-K lighting MB2 Bedienungsanleitung

B-K lighting

B-K lighting Altair Bedienungsanleitung

B-K lighting

B-K lighting SQUARE ADJUSTABLE WELL STAR Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Series Bedienungsanleitung

B-K lighting

B-K lighting PRECISION2 CO2 Series Bedienungsanleitung

B-K lighting

B-K lighting SIGN STAR Series Bedienungsanleitung

B-K lighting

B-K lighting CORE DRILL Bedienungsanleitung

B-K lighting

B-K lighting RE1 Bedienungsanleitung

B-K lighting

B-K lighting ORION Bedienungsanleitung

B-K lighting

B-K lighting MINI-MICRO RECESSED UPLIGHT Bedienungsanleitung

B-K lighting

B-K lighting INTEGRAL DENALI Series Bedienungsanleitung

B-K lighting

B-K lighting ArtiStar Remote ES16 Metal Halide Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung