Bradley E19-310DC Bedienungsanleitung

P.O. Box 309, Menomonee Falls, WI USA 53052-0309

PHONE 800.BRADLEY (800.272.3539) FAX 262.251.5817

bradleycorp.com

Installation

215-163DCE Rev. A; ECN 08-512

Page 1 of 5 9/11/08

E19-310DC

Combination Drench Shower

and Eyewash

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . 2

Installation Instructions. . . . . . . . . . . . . . . . . . 3

Assembly of Components . . . . . . . . . . . . . . . 4

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

E19-310DC Installation

9/11/08 Bradley Corporation • 215-163DCE Rev. A; ECN 08-512

IMPORTANT

Read this installation manual completely to ensure proper installation, then file it

with the owner or maintenance department. Compliance and conformity to drain

requirements and other local codes and ordinances is the responsibility of the installer.

Separate parts from packaging and make sure all parts are accounted for before

discarding any packaging material. If any parts are missing, do not begin installation

until you obtain the missing parts.

Flush the water supply lines before beginning installation and after installation is

complete. Test the unit for leaks and adequate water flow. Main water supply to the

eyewash should be “ON” at all times. Provisions shall be made to prevent unauthorized

shutoff.

The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a

minimum 0.21 MPa (30 PSI) flowing pressure. Flushing fluid should be tepid per ANSI

Z358.1.

The inspection and testing results of this equipment should be recorded weekly to verify

proper operation. This equipment should be inspected annually to ensure compliance

with ANSI Z358.1.

Workers who may come in contact with potentially hazardous materials should be

trained regarding the placement and proper operation of emergency equipment per ANSI

Z358.1.

For questions regarding the operation or installation of this product, visit www.

bradleycorp.com or call 1-800-BRADLEY.

Product warranties and parts information may also be found under ”Products” on our

web site at www.bradleycorp.com.

Installation

THIS

SIDE

Packing List

•

P.O.Box309,MenomoneeFalls,WI53051

TESTTHISUNITEACHWEEK

Test-operatevalve(s) each week and sign below.

Reportany malfunctions immediately.

Ventil(e)wöchentlich im Testbetriebprüfen, bestätigt

durchUnterschrift. Jegliche Störung sofort melden.

Date

Datum

Date

Signed

Unterschrift

Signe

Date

Date Signed

Signed

DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.

ESSAIHEBDOMADAIRE

Testle fonctionnement des valves chaque semaine et

signeen bas. S'il y à quelque chose qui ne va pas fait

unrapport immédiatement.

P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA

TEL:1-800-BRADLEY FAX:(262-251-5817)

http://www.bradleycorp.com

114-051

Installation E19-310DC

Bradley Corporation • 215-163DCE Rev. A; ECN 08-512 9/11/08

Installation

Supplies Required:

• (3) M10 floor anchors and bolts

• Teflon tape and pipe sealant

• Piping to 1-1/4" BSP water supply inlet and 1-1/4"

BSP drain outlet on unit

• Adequate supply pipe supports

• Minimum 102mm (4") drain to accommodate 115 liters

(30 gallons) per minute discharge for shower waste

• OPTIONAL: sign-mounting hardware

NOTE: Local codes may require the installation

of a backﬂow prevention valve to complete proper

installation. Compliance with local codes is the

responsibility of the installer. Valve must be tested

annually to verify that it is functioning properly. Backﬂow

prevention valves are not included with the ﬁxture and

may be supplied by the contractor or purchased from

Bradley Corporation.

Step 1: Secure base to floor

1. Install three suitable anchors (supplied by installer)

for M10 bolts in the floor.

2. Bolt the base to the floor anchors using M10 bolts

(supplied by installer).

Step 2: Assemble components

1. Assemble the remaining unit components as

shown on page 4.

• Apply pipe sealant (by installer) to all male-

threaded pipe joints.

• Use the rubber grip pad provided or a strap

wrench around pipes when tightening to prevent

marring. Place the grip pad on the pipe, then

put the wrench over the grip pad and turn the

pipe with the wrench.

• Bottom edge of the showerhead should be

2159mm (7'-1") from the floor.

Step 3: Connect water supply

IMPORTANT: Do not rely on Bradley’s

Combination Unit to support supply piping.

1. Connect water supply piping to 1-1/4" BSP inlet

on unit (piping by installer). Provide adequate

supports (by installer) for supply pipe using pipe

hangers or other means.

2. Connect drain piping to 1-1/4" BSP drain outlet on

unit (piping by installer).

3. Hang the safety sign from the unit with the curtain

hooks provided (or mount it to the wall using sign-

mounting hardware by installer).

Top View From Bowl

114mm

(4-1/2")

Ø 78.7mm

(3.1")

NOTE: All dimensions assume standard thread

engagement. Variations in manufacturing allow for

+/- 3mm (1/8") per threaded joint. To ﬁnd the tolerance

of a dimension, add the number of thread joints in

between a dimension and multiply it by 3mm (1/8").

645mm

(25-3/8")

610mm

(24")

2159mm

(7'-1")

Floor

1676mm

(66")

Floor

140mm

(5-1/2")

1041mm

(41")

152mm

(6")

247mm

(9-3/4")

Ø 273mm

(10-3/4")

267mm

(10-1/2")

Ø229mm (9") Flange

with (3) Ø10mm

(3/8") Holes on Ø

203mm (8") Bolt Circle

229mm

(9")

E19-310DC Installation

9/11/08 Bradley Corporation • 215-163DCE Rev. A; ECN 08-512

Assembly of Components

P.O.BOX 309,MENOMONEE FALLS, WI 53052-0309 USA

TEL:1-800-BRADLEY FAX:(262-251-5817)

http://www.bradleycorp.com

114-052

P.O.Box 309, Menomonee Falls,WI 53051

TESTTHIS UNIT EACH WEEK

Test-operatevalve(s) each week and sign below.

Report any malfunctions immediately.

Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt

durch Unterschrift.Jegliche Störung sofort melden.

Date

Datum

Date

Signed

Unterschrift

Signe

Date

Date Signed

Signed

DIESES GERÄT1ST WÖCHENTLICH ZU PRÜFEN.

ESSAI HEBDOMADAIRE

Testle fonctionnement des valves chaque semaine et

signe en bas.S'il y à quelque chose qui ne va pas fait

un rapport immédiatement.

1-1/4" BSP

Drain Outlet

NOTE: If tee (Item 7) is used as a supply

inlet, use plug (Item 7) on tee (Item 2).

BSP threads this end

HANDLE NOTE:

Close the cover

and put the pin

through the clip

to keep closed.

1-1/4" BSP Supply Inlet

(BSP threads are noted

with black line on threads)

9.5

9.11

9.4

9.2

9.1

9.3

Flow

Control

This End

15.1

15.2

15.3

15.4

4.4

4.11

4.3

4.6

4.8

4.7

4.71

4.9

4.10

4.12

4.2

4.1

4.5

4.2

4.12

14 14.1

NOTE: Items 8.1–8.5 come preassembled as Item 8.

Items 14.1–14.12 come preassembled as Item 14.

NOTE: Use

teflon tape

only.

Installation E19-310DC

Bradley Corporation • 215-163DCE Rev. A; ECN 08-512 9/11/08

Parts List

1 131-059 1 Base

2 169-727B 2 Pipe Tee 1-1/4” NPT

3 113-006LC 1 Pipe 1-1/4” NPT x 706 mm

4 S39-226 1 Europe Eyewash Sub-Assy.

4.1 111-039 1 Inlet Drain Fitting

4.2 169-025 2 Street Elbow 1/2” NPT

4.3 S06-136 1 Plgd. Nipple 1-1/4” NPT x 76mm

4.4 169-841 1 Reducing Tee

4.5 142-002DA 1 Lockwasher

4.6 169-726 1 Union 1/2” Female NPT

4.7 S27-282 1 1/2” Ball Valve with Nut

4.71 110-215 1 Jam Nut only

4.8 113-006QX 1 Pipe 1-1/4” NPT x 180mm

4.9 169-764 1 90° Pipe Elbow 1-1/4” NPT

4.10 113-006LE 1 Pipe Nipple 1-1/4” NPT x 76mm

4.11 169-727 1 PIpe Tee 1-1/4” NPT

4.12 113-006LQ 3 Pipe 1/2” NPT x 76mm

5 113-006LW 2 Pipe 1-1/4” NPT x 579 mm

6 169-722B 1 Reducing Tee

7 169-724 1 Pipe Plug 1-1/4” NPT

8 113-006LL 1 Pipe 1” NPT x 234 mm

9 S30-059 1 Stay-Open Ball Valve Assy. 1” NPT

9.1 S27-278 1 1” Ball Valve with Jam Nut

9.11 110-214 1 Jam Nut only

9.2 140-720 1 Stop Bracket

9.3 124-048 1 Washer, Friction

9.4 128-129 1 Handle

9.5 142-002DC 1 Lockwasher

10 128-156A 1 Pull Rod - 24” Long

11 113-006LK 1 Pipe 1” NPT x 310 mm

12 169-847 1 90° Elbow 1” NPT

13 151-001 2 Curtain Hook

14 S24-188 1 Plastic Showerhead Assembly

14.1 S24-187 1 Flow Control Assembly, 23 GPM

15 S45-1782 1 Cup Strainer Prepack

15.1 124-028 1 Center Seal Gasket

15.2 173-009 1 Cup Strainer

15.3 S21-071 1 Stem Pipe Assembly

15.4 113-1159 1 Spacer, Drain

16 S90-009 1 Dust Cover Assembly

17 269-447 1 Bumper

18 161-025 1 Nut

19 S05-091 1 Eyewash Yoke

20 S08-056 1 Handle Assembly

21 153-372R 1 Adapter

22 204-421 1 Emergency Tag

23 114-052E 1 Safety Sign

24 269-915 1 Grip Pad (not shown)

Item Part No. Qty Description Item Part No. Qty Description

Prepack S30-087 includes Items 4.71, 4.5, 20

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley Advocate LA Series Bedienungsanleitung

Bradley

Bradley Express ELX Series Bedienungsanleitung

Bradley

Bradley S19-220ABF Bedienungsanleitung

Bradley

Bradley S19-220SC Bedienungsanleitung

Bradley

Bradley Aerada 900 Series Bedienungsanleitung

Bradley

Bradley Express EXD Series Bedienungsanleitung

Bradley

Bradley Terreon TDWL22 Bedienungsanleitung

Bradley

Bradley S19-220ABF Bedienungsanleitung

Bradley

Bradley S59-2005 Bedienungsanleitung

Bradley

Bradley Verge LVRD Series Bedienungsanleitung

Bradley

Bradley S19-220SS Bedienungsanleitung

Bradley

Bradley S19-315BF Bedienungsanleitung

Bradley

Bradley Corner-Fount MF2922 Kurzanleitung

Bradley

Bradley Navigator S19-2010 Series Bedienungsanleitung

Bradley

Bradley S19-465 Bedienungsanleitung

Bradley

Bradley S19-125SBF Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley FL-3H Bedienungsanleitung

Bradley

Bradley S19-110SS Bedienungsanleitung

Bradley

Bradley MG-2/BIR3 Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley COMBI5500 Handbuch

Bradley

Bradley FREQUENCY FL-1H Bedienungsanleitung

Bradley

Bradley Sentry SN2008/IR Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema