Bradley Verge LVRD Series Bedienungsanleitung

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

215-1671 Rev. L: ECN 19-08-037C

Page 1 of 11 2/27/2020

LVRD3

Verge®Lavatory System – LVRD-Series

with Evero®Natural Quartz Material

Table of Contents

Components..................................2

Supplies Required .............................3

Dimensions ................................3–4

Rough-Ins ...................................5

Frame Mounting...............................6

Drain Assembly ...............................7

Faucets and Optional Soap Valve .................7

Bowl Mounting ................................8

Strainer and P-Trap ............................9

Adjust the Temperature .........................9

Trap Cover ..................................10

Cleaning and Maintenance .....................11

WARNING

Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation.

Electrical power MUST remain off until installation is complete.

Installer’s hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out

rating of 1,000 lb.

NOTICE

Make sure that all water supply lines have been flushed and then completely turned off before beginning

installation. Debris in supply lines can cause valves to malfunction.

IMPORTANT

Read this entire installation manual to ensure proper installation. When finished with the installation, file

this manual with the owner or maintenance department. Compliance and conformity to local codes and

ordinances is the responsibility of the installer. Product warranties may be found under “Products” on our

Web site at bradleycorp.com.

Separate parts from packaging and make sure all parts are accounted for before discarding any packaging

material. If any parts are missing, do not begin installation until you obtain the missing parts.

For standard height mounting, do not exceed the recommended 34" distance from the top of the lav deck

to the finished floor. To meet ADA requirements, the lav deck cannot exceed the 34" maximum height

dimension.

LVRD3 Installation

22/27/2020 Bradley • 215-1671 Rev. L: ECN 19-08-037C

Components

TMV Valve

(½" NPTM Outlet)

(S45-2478)

Chrome P-Trap (S29-094)

Plastic P-Trap (269-1697)

Frame

(S17-363)

Access Panel

(186-2281)

Hose Prepack

(S45-2730)

Supply Fittings

(Standard)

(S45-2512)

and

(S45-3004)

for Verge Faucets

S53-3100, S53-3300,

S53-3500, & S53-3700

Supply Fittings

(Standard)

(S45-2512)

and

(S45-3005)

for Verge Faucets

S53-3100, S53-3300,

S53-3500, & S53-3700

Hose Prepack

(S45-2731)

TMV Supply Connections Tempered Supply Connections

Bowl

Contact your Bradley Representative for color options

Complete Drain Prepack

(S45-2471)

Strainer and

Screw

(S45-2479)

O-Ring

(125-111)

Drain

Adapter

Packing

Washer

#10-24

Screw

Drain Adapter

Prepack

(S45-2480)

Complete Hardware Prepack (S45-2473)

Frame Mounting Qty.

Washer, Square 9

Washer, Flat 1" O.D. 2

Bowl-To-Frame (S45-2481) Qty.

Screw, ¼-20 x ½" 3

Washer, Flat ⁵⁄₈" O.D. 3

Trap Cover (S45-2482) Qty.

Screw, 10-24 x ½" 6

#10 Finishing Washer 6

Trap Hook Bracket 1

Screw, 10-24 x 3⁄8" 1

Washer, Flat 35⁄64" O.D. 1

Plastic

Hose

Plastic

Hose

Stainless

Steel

Hose

Plastic

Hose

Plastic Hose

Water supply to battery box solenoid MUST be supplied

using a plastic hose (provided by Bradley).

Stainless

Steel

Hose

Plastic

Hose Plastic

Hose

Installation LVRD3

Bradley • 215-1671 Rev. L: ECN 19-08-037C 2/27/2020 3

Dimensions (mm)

30"

(762)

90"

(2286)

30"

(762)

66"

(1676)

Top View

Front View

Supplies Required:

• (11)

3⁄8" lag screws, wall anchors and bolts (minimum pull-out rating of 1,000 lb)

• ½" hot/cold or tempered supply piping

• 1½" NPT drain piping

• OPTIONAL: (2) 110V GFCI protected electrical outlets for 100–120V AC plug-in transformers (for Verge Faucets)

• Screen filter(s) as needed, if not included with faucet(s)

90"

(2286)

LVRD3 Installation

42/27/2020 Bradley • 215-1671 Rev. L: ECN 19-08-037C

Dimensions – Side View (mm)

33½"

(851)

32½"

(826)

22½"

(572)

15¹⁄16"

(392)

15¹⁄16"

(392)

15¹⁄16"

(392)

15¹⁄16"

(392)

8⁷⁄₁₆"

(214)

8⁷⁄₁₆"

(214)

8⁷⁄₁₆"

(214)

8⁷⁄₁₆"

(214)

14⁷⁄₈"

(378)

10⁷⁄₈

(277)

11⁷⁄₈"

(302)

12⁷⁄₈"

(328)

30½"

(775)

29½"

(749)

22½"

(572)

28½"

(724)

29½"

(749)

22½"

(572)

30½"

(775)

22½"

(572)

31½"

(800)

Standard

Height

Juvenile

Height

TAS, Grades 6

through 8 or 9

TAS, Pre-K

through Grades

5 or 6

Installation LVRD3

Bradley • 215-1671 Rev. L: ECN 19-08-037C 2/27/2020 5

Rough-Ins

RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FOR CODES A–E and H FIXTURE STYLE

33½" None Standard Height

31½" Subtract 2" TAS, Grades 6 through 8 or 9

29½" Subtract 4" TAS, Pre-K through Grades 5 or 6

30½" Subtract 3" Juvenile Height

27⁷⁄₁₆"

(697)

BAD GG GG

31½"

(800)

31"

(787)

427⁄8"

(1089)

427⁄8"

(1089)

21"

(533)

21"

(533)

27¹⁄₈"

(688)

267⁄8"

(682)

(76)

27"

(686)

27"

(686)

235⁄8"

(600)

2½"

(64)

21⁹⁄₁₆"

(548)

10¾" (273)

4" (102)

Finished Floor

(76)

B B B

5.550

20¹⁵⁄₁₆"

(531)

30¼"

(768)

30¹⁄₆"

(763)

CODE DESCRIPTION QTY.

3⁄8

" Lav Deck Bowl Anchors with a Minimum Pull-Out Force of 1,000 lb (reinforce walls at anchor points) 2

3⁄8

" Lav Deck Frame Anchors with a Minimum Pull-Out Force of 1,000 lb (reinforce walls at anchor points) 9

H, C ½" Hot/Cold Supplies, Stub-Out 2" From Wall 1

D110V GFI Protected Electrical Outlet (AC version only)

Three single outlets are required for CAP-DCR faucets due to the size of the transformers. 3

E1½" NPT Drain, Stub-Out 2" from Wall 1

F#10 Anchors for Faucet Control Box Installation 6

G#10 Anchors for Soap Tank Installation 4

13¾"

(349)

13"

(331)

3³⁄₁₆"

(80)

Standard rough-in shown.

Areas marked with a crosshatch require sufﬁcient

backing compliant with local building codes.

Approx. Soap

Battery Box

Location

Approx. Soap

Battery Box

Location

LVRD3 Installation

62/27/2020 Bradley • 215-1671 Rev. L: ECN 19-08-037C

1Frame Mounting

Typical installation is shown. It may be necessary to repair the wall

after mounting. The ﬁxture may not cover all of the wall modiﬁcations.

16"

(406mm)

centers

14"

(356mm)

Floor

Drywall

Drain, supplies and electrical box are

shown in their approximate locations.

Cut clearance holes in the plywood as

required.

NOTE: Plywood should equal the

thickness of the drywall (½" minimum).

Fasten plywood securely

to at least (4) studs.

Use 3⁄8" lag screws and square washers provided to secure

the frame to plywood (9) places. Shim frame as necessary.

NOTE: Other fasteners may be used based on wall material.

Plywood Mounting Height "A" Dimension

Standard Height 18" (457 mm)

TAS, Grades 6 through 8 or 9

16" (406 mm)

TAS, Pre-K through Grades 5 or 6

14" (356 mm)

Juvenile Height 15" (381 mm)

Shim the frame at anchor points to

ensure the offset bracket is straight.

Leave the top three screws loose.

Minimum required to

pick up four studs and

vertical frame members

–56" (1422mm) min.

56"

(1422mm)

Installation LVRD3

Bradley • 215-1671 Rev. L: ECN 19-08-037C 2/27/2020 7

3Faucets and Optional Soap Valve

For ease of installation, leave the bowl laying on its back.

See Faucet and Soap installation instructions for assembly.

2Drain Assembly

For ease of drain installation,

lay the bowl on its back.

O-Ring

Drain Adapter

Packing Washer

#10-24

Screw

LVRD3 Installation

82/27/2020 Bradley • 215-1671 Rev. L: ECN 19-08-037C

4a Bowl Mounting (to Frame)

Washer

¼"-20

Screw

4b Bowl Mounting (to Wall)

Reinforce behind the wall

at the two bowl mounting

locations, then secure the

bowl to the wall.

Press firmly on the back

of the bowl to seat the

bowl into the frame.

Tighten the top three

screws on the frame.

Bowl is heavy!

Cold

Hot

Optional TMV Valve

(½" NPTM Outlet)

Connect faucet hoses. Slide

through keyhole slots from behind.

Optional

Tempered

Supply

TMA Option

NONE Option

Plastic

Hose

Plastic

Hose

Stainless

Steel

Hose

Water supply to battery box solenoid MUST be supplied

using a plastic hose (provided by Bradley).

Stainless Steel Hose

Plastic

Hose Plastic

Hose

Installation LVRD3

Bradley • 215-1671 Rev. L: ECN 19-08-037C 2/27/2020 9

Strainer

5Strainer and P-Trap

Thread the strainer screw

through the boss on the

drain adapter and secure

the strainer to the bowl.

Attach the strainer

screw to the strainer.

Do not overtighten.

6Adjust Temperature with Water Running

ALoosen Cap Screw about 1/4" (4-6 turns)

and lift up cover (do not remove).

BUsing cover, turn cartridge gently until

desired water temperature is reached. Do

not turn past stops as this may damage

unit. Push cover down and tighten screw.

This valve is NOT factory preset.

Upon installation, the temperature

of this valve must be checked and

adjusted to ensure delivery of a

safe water temperature. Water

in excess of 110°F (43°C) may

cause scalding.

LVRD3 Installation

10 2/27/2020 Bradley • 215-1671 Rev. L: ECN 19-08-037C

7Trap Cover

Hang the trap cover onto

the hook, then secure

the trap cover with the

screws provided, starting

with the side screws.

Hook

#10-24

Screw

Washer

#10-24

Flat Head

Screw

Finishing

Washer

Make all connections before installing trap cover.

Andere Handbücher für Verge LVRD Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley SN2003 Kurzanleitung

Bradley

Bradley S19294 Series Bedienungsanleitung

Bradley

Bradley S19-210SC Bedienungsanleitung

Bradley

Bradley S67-504 Bedienungsanleitung

Bradley

Bradley Sentry SN2003/TT Bedienungsanleitung

Bradley

Bradley EXPRESS SS-2/AST/JUV Bedienungsanleitung

Bradley

Bradley S19-304D1 Bedienungsanleitung

Bradley

Bradley Terrazzo WF2613 Bedienungsanleitung

Bradley

Bradley Verge Crestt Series Kurzanleitung

Bradley

Bradley Aerada 1000 Series Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley S19-690 Bedienungsanleitung

Bradley

Bradley S19-230FW Bedienungsanleitung

Bradley

Bradley Terreon Deep Bowl WF3200 Series Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley Equa-Flo Pressure Balancing Valve Bedienungsanleitung

Bradley

Bradley Verge LVQD1 Bedienungsanleitung

Bradley

Bradley S19-220ABF Bedienungsanleitung

Bradley

Bradley S19-120SS Bedienungsanleitung

Bradley

Bradley SN2013/AST4 Bedienungsanleitung

Bradley

Bradley Corner-Fount MF2922 Kurzanleitung

Bradley

Bradley E19-310DC Bedienungsanleitung

Bradley

Bradley Express ELX Series Bedienungsanleitung

Bradley

Bradley Express MG Series Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema