Bradley Express MG Series Bedienungsanleitung

Installation

215-1324 Rev. W; ECN 13-08-025

Page 1 of 15 4/9/2014

MG-2/IR

Express®Lavatory

System - MG Series

with Adaptive

Infrared Control

Table of Contents

Pre-Installation Information ...................2

Dimensions..................................3

Supplies Required ...........................3

Rough-Ins ...................................4

Installation ............................5–9

Components.........................10–11

Cleaning and Maintenance ................12

Adaptive Infrared Troubleshooting ...........13

Solenoid Valve Troubleshooting .............14

Navigator®Mixing Valve Troubleshooting ......15

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 800.BRADLEY (800.272.3539) Fax: 262.253.4161

bradleycorp.com

MG-2/IR Installation

24/9/2014 Bradley • 215-1324 Rev. W; ECN 13-08-025

IMPORTANT!

Read this entire installation manual to ensure proper installation. For optional

soap dispenser, refer to Installation Instructions for Express®Lavatory System

MG-Series document 215-1585. When ﬁnished with the installation, ﬁle this manual

with the owner or maintenance department. Compliance and conformity to local

codes and ordinances is the responsibility of the installer.

Separate parts from packaging and make sure all parts are accounted for

before discarding any packaging material. If any parts are missing, do not begin

installation until you obtain the missing parts.

Make sure that all water supply lines have been ﬂushed and then completely

turned off before beginning installation. Debris in supply lines can cause valves to

malfunction.

Turn OFF electrical power to the electrical outlets, then unplug all electrical

units prior to installation. Electrical power MUST remain off until installation is

completed. After installation is complete, turn on the water supply ﬁrst, then turn

on the electrical power.

Hardware supplied by installer must be appropriate for wall construction. Wall

anchors used must have a minimum pull-out rating of 1,000 lbs. Overtightening

fasteners can damage the Terreon®material. Use caution when tightening bowl and

sprayhead fasteners.

Product warranties may be found under “Product Information” on our web site at

www.bradleycorp.com.

Installation

THIS

SIDE

Packing List

•

Installation MG-2/IR

Bradley • 215-1324 Rev. W; ECN 13-08-025 4/9/2014 3

54"

(1372mm)

42"

(1067mm)

15"

(381mm)

15"

(381mm)

Dimensions

27"

(686mm)

47"

(1194mm)

22"

(559mm)

39"

(991mm)*

33½"

(851mm)*

29½"

(749mm)*

17½"

(445mm)*

21½"

(546mm)

9½"

(241mm)

* Subtract 4" from all vertical dimensions for Juvenile Height Mounting.

Subtract 3½" from all vertical dimensions for TAS Juvenile Height Mounting (grades Pre-K through 5 or 6).

Subtract 1½" from all vertical dimensions for TAS Juvenile Height Mounting (grades 6 through 8 or 9).

Supplies Required:

• (8)3/8" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall (minimum pull-out rating of

1,000 lbs.)

• ½"Nominalcoppertubingforhotandcoldsuppliesand1½"NPTdrainpiping

• 110voltelectricaloutletfor110/24VACplug-intransformer(supplied)

• 240/208voltor277voltelectricaloutletforoptionalelectricaltanklesswaterheater

MG-2/IR Installation

44/9/2014 Bradley • 215-1324 Rev. W; ECN 13-08-025

1Rough-Ins

5" (127mm)

FLOOR

CENTERLINE OF FIXTURE

APPROX. DIMENSION

A,E

3¾"

(95mm)

TEMPERED

SUPPLY

26¼"

(660mm)*

³⁄

(568mm)*

31½"

(800mm)*

24½"

(622mm)*

25½" (648mm)

CODE DESCRIPTION QTY.

A3/8" Wall Anchors with a minimum pull-out force of 1,000 lbs. for Bowl 2

B3/8" Wall Anchors with a minimum pull-out force of 1,000 lbs. for Main Frame 6

C1 ½" Nominal Copper Tubing Hot Supply, stub out 2" from wall 1

C2 ½" Nominal Copper Tubing Cold or Tempered Supply, stub out 2" from wall 1

D1-1/2" NPT Drain, stub out 2" from wall 2

Onthebowlback,measurethedistancebetweenthe¾"bowlmountingholes.Dividethismeasurement

inhalf.Measureandmarkthisdimensiononthewalltotheleftandtherightofthecenterline.Installtwo

3/8"wallanchorswithaminimumpull-outratingof1,000lbs.(suppliedbyinstaller)atlocationsmarked.

FWater Heater Option #1: Rough in appropriate electrical supply per local code (recommended location for

240/208V or 277V electrical box [4"L x 3"W x 4"H shown]) 1

GWater Heater Option #2: Rough in appropriate electrical supply per local code (recommended location for

240/208V or 277V electrical box [2½"L x 3"W x 4"H]) 1

H 110V GFCI Protected Electrical Outlet 1

RIM HEIGHT * VERTICAL HEIGHT ADJUSTMENTS FIXTURE STYLE

33½" None Standard Height

32" Subtract 1½" TAS, Grades 6 through 8 or 9

29½" Subtract 4" Juvenile Height

30" Subtract 3½" TAS, Pre-K through 5 or 6

B B

(102mm)

A,E

25¾"

(654mm)*

28¼"

(718mm)*

19½"

(495mm)*

16½"

(419mm)

14"

(356mm)

14"

(356mm)

APPROX. DIMENSION

25½" (648mm)

NOTE: The Express®Lavatory System with Adaptive Infrared Control (model MG-2/IR) must have a rim height no higher

than 34" above finished floor to be compliant with Americans with Disabilities Act (ADA). When mounted at 33½" rim

height, the MG-2/IR Express®meets ADA, ANSI and UFAS requirements for barrier-free clearances, reaches and

controls. Always check local codes and ordinances for compliance.

C1 C2

23"

(584mm)*

Installation MG-2/IR

Bradley • 215-1324 Rev. W; ECN 13-08-025 4/9/2014 5

Secure the bowl to the wall anchors

with two 3/8" bolts and washers. Do

not overtighten bolts.

Attach the front of the bowl to the frame

using the two ¼-20 x ½" pan-head

screws and washers provided. Do not

tighten screws at this time.

Tighten the screws to secure the bowl

assembly to the frame. Do not overtighten.

If necessary, adjust sprayhead body to fit

closely to the wall by adjusting the sprayhead

mounting bolts. Refer to the components

illustration for bolt locations.

2Mount the Frame

3Install the Bowl

Anchoring the frame to a wall that is not flat may cause the frame to

bend, making it difficult to reinstall the access panels. If necessary,

use shims to compensate for wall distortion.

Loosen, but do not

remove the bottom

panel screws.

ARemove the top access panel

screws and washers and

remove the access panel.

Once you have positioned

the frame such that it is level

and flat against the wall or

shimmed, use the 3/8" bolts

and washers (6 places) to

mount the frame to the wall.

If the fixture has a soap option, refer to the soap

system installation manual (215-1585) before

installing the bowl assembly.

MG-2/IR Installation

64/9/2014 Bradley • 215-1324 Rev. W; ECN 13-08-025

4a Connect the Supply — Hot and Cold Supply

4b Connect the Supply — Single Tempered Supply

The letter “H” on the Navigator®Mixing

Valve indicates hot water supply inlet.

Loosen but do not remove

the two mounting screws

holding the valve bracket

to the frame.

Slide the valve bracket up

and lift it from the frame.

Connect one end of each hose to the Navigator

valve (one on the hot side, one on the cold side).

Connect the other swivel end to the stops.

Attach the stops onto the hot and cold wall

stub-outs.

Loosen but do not remove the two

mounting screws holding the valve

bracket to the frame.

Slide the valve bracket up and lift

it from the frame.

Connect one end of flexible hose

to the tempered line adapter.

Connect the other swivel end to

the stop.

Attach the stops onto the wall

stub-out.

Installation MG-2/IR

Bradley • 215-1324 Rev. W; ECN 13-08-025 4/9/2014 7

To Drain

Stub-Out

5Install the Drain

6Connect Optional Electric Tankless Water Heater

240/208 or 277 voltage is required for hot water heater.

Refer to the installation manual provided with the hot

water heater for further installation information.

Connect the ½" flexible hose

from the cold water supply

stub-out to the hot water

heater inlet.

Hang the water heater on the

rear frame member to the right

of the vertical frame member.

Connect the ½" flexible hose

from the hot water heater

outlet to the supply inlet on

the solenoid valve assembly.

Recommended

electrical box

location

Optional

electrical box

location

2" (51mm)

REF. ONLY

MG-2/IR Installation

84/9/2014 Bradley • 215-1324 Rev. W; ECN 13-08-025

7Connect the Electrical and Tubing

Connect the circuit plug from

the transformer to the female

transformer circuit plug.

Connect the sensor circuit

plug from the sprayhead to

the solenoid circuit plug.

WARNING:

The Express®control must be connected with the 24 VAC Class II transformer provided. Connections to

110 VAC can cause personal injury and will result in damage to the electronics.

Connection of leads other than shown may cause permanent damage to the sensor.

Loosen the compression nuts.

Push the sprayhead supply tubes firmly

into the tube connectors until they are

fully seated.

Tighten the compression nuts by hand.

Installation MG-2/IR

Bradley • 215-1324 Rev. W; ECN 13-08-025 4/9/2014 9

Align the valve bracket mounting screws with slots on the frame. Let the valve bracket slide down to lock into place.

Turn on the water supply and check for leaks. Turn on the electrical power to the electrical outlet and pass your hand in front of

each station’s sensor until all the air is purged from the lines and water is flowing smoothly. Reinstall the access panel.

START-UP NOTE: Wait two full minutes after making the power connection before using the lav. The sensors will take up to

eight full minutes (while not in use) to adapt to the bowl if another object is detected during the two-minute start-up period.

Check the temperature when approximately 1.0 GPM water flow is reached and adjust if necessary (the range of the valve is

95°F–125°F (35°C–52°C).

ALoosen Cap Screw about ¼" (4-6 turns)

and lift up cover (do not remove).

Using cover, turn cartridge gently until

desired water temperature is reached.

Do not turn past stops as this may

damage unit. Push cover down and

tighten screw.

This valve is NOT factory preset. Upon installation, the temperature of this

valve must be checked and adjusted to ensure delivery of a safe water

temperature. Water in excess of 110°F (43°C) may cause scalding.

8Adjust Temperature with Water Running

MG-2/IR Installation

10 4/9/2014 Bradley • 215-1324 Rev. W; ECN 13-08-025

Components

STAINLESS STEEL

ACCESS PANEL

(186-1263)

SPRAYHEAD

MOUNTING BOLTS (3)

DRAIN ASSEMBLY

PLUG-IN

TRANSFORMER

1/8" RUBBER WASHER

125-001DP

#8-32 SCREW

(160-319)

TAILPIECE

129-056

P-TRAP

269-1697

(POLYPROPYLENE)

S29-094

(CHROME-PLATED BRASS)

DRAIN PLUG

P16-072

STRAINER

P16-075

110/24 VAC CLASS II

TRANSFORMER

S83-152

SPRAYHEAD BODY

(PART NUMBER VARIES WITH

COLOR OF UNIT. CONTACT

YOUR LOCAL BRADLEY REP.

FOR ASSISTANCE).

BOWL

(PART NUMBER VARIES WITH

COLOR OF UNIT. CONTACT

YOUR LOCAL BRADLEY REP.

FOR ASSISTANCE).

END CAP (RIGHT)

(PART NUMBER VARIES WITH

COLOR OF UNIT. CONTACT

YOUR LOCAL BRADLEY REP.

FOR ASSISTANCE).

END CAP (LEFT)

(PART NUMBER

VARIES WITH COLOR

OF UNIT. CONTACT

YOUR LOCAL

BRADLEY REP. FOR

ASSISTANCE).

1/4"-20 x 1/2"

PAN HEAD

SCREW (qty. 4)

(160-389)

1/4"-20

WASHER

(qty. 4)

(142-002DB)

BOWL MOUNTING

HARDWARE

Andere Handbücher für Express MG Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley SN2003 Bedienungsanleitung

Bradley

Bradley S45-1964 Bedienungsanleitung

Bradley

Bradley S19-130F Bedienungsanleitung

Bradley

Bradley S19-220HFP Bedienungsanleitung

Bradley

Bradley Express EXD Series Bedienungsanleitung

Bradley

Bradley Express ELX Series Bedienungsanleitung

Bradley

Bradley Aerada 1200 Series Bedienungsanleitung

Bradley

Bradley S19-310DCBF Bedienungsanleitung

Bradley

Bradley Aerada 1000 Series Bedienungsanleitung

Bradley

Bradley S96-085 Bedienungsanleitung

Bradley

Bradley EXD-2N Bedienungsanleitung

Bradley

Bradley MG Series Bedienungsanleitung

Bradley

Bradley Terreon MF2922 Kurzanleitung

Bradley

Bradley Navigator S19-2010 Series Bedienungsanleitung

Bradley

Bradley S19-210FW Bedienungsanleitung

Bradley

Bradley Express SS-2N/AST/STD Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley LC800 Bedienungsanleitung

Bradley

Bradley S19-220FWPT Bedienungsanleitung

Bradley

Bradley S19-220DC Bedienungsanleitung

Bradley

Bradley SN2013/AST4 Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley Express Crescent CRS Series Bedienungsanleitung

Bradley

Bradley S19-310DCFW Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema