Bradley Terreon Quadra-Fount MF2944/IR Bedienungsanleitung

IMPORTANT!

Read this entire installation manual to ensure proper installation.

When finished with the installation, file this manual with the owner or

maintenance department.

Separate parts from packaging and make sure all parts are accounted

for before discarding any packaging material. If any parts are

missing, do not begin installation until you obtain the missing parts.

Water supply requires a flowing pressure of at least 20 psi, but no

greater than 80 psi.

Make sure that all water supply lines have been flushed and then

completely turned off before beginning installation. Debris in supply

lines can cause valves to malfunction.

Hardware supplied by installer must be appropriate for wall

construction. Wall anchors used must have a minimum pull-out

rating of 1,000 lbs.

The Adaptive® Infrared control must be connected with a 24 VAC

Class II transformer. Connections to 110 VAC can cause personal

injury and will result in damage to the electronics.

Product warranties may be found under "Product Information" on our

web site at www.bradleycorp.com.

THIS

SIDE

Packing List

Installation

MF2944/IR

Terreon®Quadra-Fount®

Washfountain with Adaptive

Infrared Control

(Standard* & Juvenile Height)

* Standard Height is ADA Compliant

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1-800-BRADLEY Fax: (262) 251-5817

http:\\www.bradleycorp.com

215-1180 Rev R; EN 06-915C

Page 1 of 17 10-28-2005

MF2944/IR Installation

2 10-28-2005 Bradley Corporation • 215-1180 Rev. R; EN 06-915C

Table of Contents

Pre-installation information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Parts included with the Quadra-Fount® . . . . . . . . . . . . . . . . . . . . . . . . .4

Step 1 Rough-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Step 2 Assemble pedestal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Step 3 Install pedestal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Step 4 Install solenoid assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Step 5 Assemble and install bowl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Step 6 Electrical and supply connections . . . . . . . . . . . . . . . . . . . . . . . .10

Step 7 Check operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Vernatherm™ Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Step 8 Install top cover and front panel . . . . . . . . . . . . . . . . . . . . . . . . .11

Cleaning and maintenance instructions . . . . . . . . . . . . . . . . . . . . . .12-13

Solenoid valve troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15

Thermostatic mixing valve troubleshooting . . . . . . . . . . . . . . . . . . .16-17

Cleaning the Strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17

Supplies Required by Installer

• (6) 3/8" diameter bolts with washers and (6) wall anchors appropriate for your installation

• (2) 3/8" diameter bolts with washers and (2) floor anchors appropriate for your installation

• 1/2" NPT hot and cold water supply lines

• 1-1/2" NPT drain trap and waste connection

• Pipe sealant and plumber’s putty

• 110 VAC power source for 110/24 VAC plug-in transformer supplied

• OPTIONAL: Bradley recommends installing an electrical cut-off switch to the unit. This feature

prevents accidental water delivery during regular maintenance and service.

Installation MF2944/IR

3Bradley Corporation • 215-1180 Rev. R; EN 06-915C 10-28-2005

Pre-installation information

Terreon® material

The Quadra-Fount® is constructed of Terreon®, a densified solid surface material composed of

polyester resin. Terreon®is resistant to chemicals, stains, burns and impact. Surface damage can be

easily repaired with everyday cleaners or fine-grit abrasives. Terreon® is NAHB certified to meet

ANSI Z124.3, Z124.6 and ANSI/ICPA SS-1-2001.

Adaptive sensor and solenoid valve

Each nozzle is controlled by a separate solenoid valve, allowing each user to activate a flow of

tempered water from one spray nozzle. Each valve uses less than half the maximum amount of hot

water allowed by the ANSI/ASHRAE/IES 90A-1980 Standard.

Adaptive Infrared sensor: The Adaptivesensor modules are housed in the sprayhead. The sensor

eyes are secured behind the sprayhead to protect it from water, soap, and dirt. The sensor is accessible

by removing the top cover. All electrical components are housed within the pedestal.

Solenoid valve: An electronically controlled solenoid valve serves as the metering mechanism. Few

moving parts provide reliable metering performance and the solenoid is unaffected by chemicals and

minerals often present in municipal water supplies.

Barrier-free and ADA compliant

The Terreon® Quadra-Fount® with Adaptive Infrared is designed to comply with all ADA guidelines

on reaches, clearances and operation when mounted at standard height dimensions by the installer

(see page 5 of this instruction manual for rough-in and mounting dimensions).

MF2944/IR Installation

4 10-28-2005 Bradley Corporation • 215-1180 Rev. R; EN 06-915C

MOUNTING PANELS

Solenoid Assembly with

Two Mounting Screws

TEMPERED LINE

S45-2081 (OPTIONAL)

Stop/Check

Hose

VALVE PREPACK S45-2082

Stop/Check

Hose

LOWER BRACKET

Parts included with the Quadra-Fount®

Separate all parts from packaging materials and ensure you have all the parts required for assembly.

If any parts are missing, do not attempt to assemble the Bradley Terreon®Quadra-Fount®

Washfountain until you obtain all parts.

Installation MF2944/IR

5Bradley Corporation • 215-1180 Rev. R; EN 06-915C 10-28-2005

(178)

7-1/8" *

(181)

(51)

11"

(279)

11"

(279)

17-1/2" *

(445)

24" *

(610)

19-1/2"

(495)

28" *

(711)

7-1/2"

(191)

(178)

9-1/2" *

(241)

110V GFI ELECTRICAL

OUTLET RECOMMENDED

LOCATION (REFER TO LOCAL

CODES BEFORE ROUGH-IN)

SUPPLIES THROUGH FLOOR

(OPTIONAL) STUB UP 3"

1-1/2" NPT WASTE CONNECTION

THROUGH FLOOR - 3" FROM WALL

1/2 NPT SUPPLIES - 5" FROM WALL

STUB OUT MIN. 1-1/2"

FROM FLOOR

1/2 NPT SUPPLIES

STUB OUT MIN. 1-1/2"

FROM WALL

1-1/2 NPT WASTE CONNECTION

FOR USE WITH 1-1/2" TUBULAR P-TRAP

STUB OUT MIN. 1-1/2"

(2) APPROPRIATE ANCHORS

AND 3/8" BOLTS (SUPPLIED

BY INSTALLER TO MOUNT

BOWL TO WALL

MOUNTING PANELS

(76)

(127)

FINISHED FLOOR

7-1/2"

(191)

* Subtract 4" (101) from this dimension for juvenile height model.

1Rough-ins IMPORTANT:

Flush the supply lines before making connections. Debris in

supply lines will cause the valves to malfunction.

IMPORTANT:

Compliance and conformity to local codes and ordinances is

the responsibility of the installer.

CAUTION:

The Quadra-Fount® must be connected with a 24 VAC Class II

plug-in transformer. Connection with 110 VAC will result in

damage to the electronics and could result in personal injury.

ROUGH IN 1/2" NPT HOT AND

COLD SUPPLY LINES THROUGH

WALL OR FLOOR AT

DIMENSIONS SHOWN.

ROUGH IN 1-1/2" NPT DRAIN

WASTE CONNECTION THROUGH

WALL OR FLOOR AT

DIMENSIONS SHOWN.

MF2944/IR Installation

6 10-28-2005 Bradley Corporation • 215-1180 Rev. R; EN 06-915C

MOUNTING

PANEL

1/4"-20 x 1/2"

PAN HEAD

SCREW

1/4"-20 x 1/2"

PAN HEAD

SCREW

5/16" I.D.

WASHER

LEFT

PEDESTAL

PANEL

UPPER

BRACKET

LOWER

BRACKET

CENTERLINE OF

FIXTURE

RIGHT

PEDESTA

PANEL

Figure 1

NOTE!

Washers are not utilized on back of mounting panels.

Refer to Figure 1 when assembling the pedestal.

FASTEN THE MOUNTING PANELS TO THE PEDESTAL

WITH FOUR PAN HEAD 1/4"- 20 X 1/2" SCREWS

SUPPLIED.

INSTALL THE UPPER BRACKET TO THE PEDESTAL

PANELS WITH TWO PAN HEAD 1/4"- 20 X 1/2"

SCREWS AND 5/16" I.D WASHERS SUPPLIED.

INSTALL THE LOWER BRACKET TO THE PEDESTAL

PANELS WITH TWO PAN HEAD 1/4"- 20 X 1/2"

SCREWS AND 5/16" I.D. WASHERS SUPPLIED.

Assemble pedestal

Installation MF2944/IR

7Bradley Corporation • 215-1180 Rev. R; EN 06-915C 10-28-2005

MOUNTING

PANEL WALLANCHO

LOCATION

FLOOR ANCHOR

LOCATION

LOWER

BRACKET

CENTERLINE

PEDESTAL

ASSEMBLY

Figure 2

3Install pedestal

NOTE!

See Figure 2 when installing the pedestal.

NOTE!

Remove molding strips or tiles which could

prevent a flush mounting to the wall.

MEASURE AND MARK THE CENTERLINE OF THE WASHFOUNTAIN

ON THE WALL AND FLOOR.

BEFORE MOUNTING THE PEDESTAL TO THE FLOOR, MAKE SURE THE FLOOR IS LEVEL. IF IT IS

NOT LEVEL, BE PREPARED TO INSTALL SHIMS WHEN POSITIONING THE PEDESTAL IN STEP C.

WITH SOMEONE TO ASSIST YOU, MOVE THE PEDESTAL ASSEMBLY TO THE WALL USING APPROPRIATE LIFTING

PROCEDURES, AND ALIGN THE LOCATING NOTCHES ON THE MOUNTING PANEL WITH THE CENTERLINE MARKED

ON THE WALL. IF THE FLOOR IS NOT LEVEL, INSTALL SHIMS UNDER THE LEFT AND/OR RIGHT PEDESTAL.

DRILL HOLES IN THE WALL THROUGH THE FOUR 1/2" DIAMETER HOLES IN THE MOUNTING PANEL AND INSTALL

FOUR ANCHORS (SUPPLIED BY INSTALLER) FOR 3/8" BOLTS.

SECURE THE PEDESTAL ASSEMBLY TO THE WALL ANCHORS USING FOUR 3/8" BOLTS AND WASHERS (SUPPLIED

BY INSTALLER).

DRILL HOLES IN THE FLOOR THROUGH THE TWO 1/2" DIAMETER HOLES IN THE LOWER BRACKET AND INSTALL

TWO ANCHORS (SUPPLIED BY INSTALLER) FOR 3/8" BOLTS.

AFTER FLOOR ANCHORS ARE INSTALLED, SECURE THE PEDESTAL ASSEMBLY TO THE FLOOR ANCHORS USING

TWO 3/8" BOLTS AND WASHERS (SUPPLIED BY INSTALLER).

WARNING:

To prevent serious injury and/or damage to

the bowl, move and position the bowl with

the assistance of another person and always

use appropriate lifting procedures.

MF2944/IR Installation

8 10-28-2005 Bradley Corporation • 215-1180 Rev. R; EN 06-915C

Braided Hose

Cold Supply Inlet

Hot Supply

Inlet

Stop/Check Valve

Vernatherm™ TMV

Solenoid Valve Assembly

1/4-20 x 1/2" Screws

Figure 3

4Install solenoid assembly

CONNECT THE 1/2" NPT FEMALE END OF THE STOP/CHECK

VALVES TO THE ROUGH-INS.

CONNECT THE SUPPLY HOSES TO THE STOP/CHECK VALVES.

NOTE!

The letter “H” on the Vernatherm™

Mixing Valve indicates hot water supply

inlet.

The thermostatic mixing valve requires

at least 115° F water from the hot water

side for proper operation. As with all

lavatories, there will be a delay in

obtaining warm water. If the hot water is

too far away from the washfountain, a

circulating pump may be required.

INSIDE THE PEDESTAL, INSTALL THE TWO 1/4-20 X 1/2" SCREWS (SUPPLIED WITH VALVE ASSEMBLY) IN THE

MOUNTING HOLES ON THE SIDE OF THE LEFT PEDESTAL PANEL. DO NOT THREAD THE SCREW COMPLETELY

INTO THE PANEL, BUT ALLOW 5/16" OF THE SCREW TO BE EXPOSED (SEE FIGURE 3)

MOUNT THE VALVE BRACKET TO THE LEFT SIDE OF THE PEDESTAL AS SHOWN.

CONNECT THE SUPPLY HOSES TO THE VERNATHERM™ TMV VALVE ASSEMBLY.

FOR OPTIONAL SINGLE TEMPERED SUPPLY: ATTACH THE STOP/CHECK VALVE TO THE 1/2" TEMPERED SUPPLY LINE.

CONNECT THE STOP/CHECK VALVE TO THE SOLENOID VALVE ASSEMBLY WITH THE FLEXIBLE SUPPLY HOSE.

Installation MF2944/IR

9Bradley Corporation • 215-1180 Rev. R; EN 06-915C 10-28-2005

Figure 4

Figure 5

Spud

Washer

#10-24 x 1/2"

Screw for

Strainer

Drain

Spud

Dome

Strainer

Discard this

washer; it is not

used on

washfountains.

Washfountain

Bowl

Spud

Locknut

Drain Assembly

Back View of Washfountain Bowl

5Assemble and install bowl

WARNING:

To prevent serious injury and/or damage to

the bowl, move and position the bowl with

the assistance of another person and always

use appropriate lifting procedures.

WARNING:

Do not leave the bowl on the pedestal

unsupported, as it may fall and cause

personal injury or damage to property.

NOTE!

Discard rubber gasket included with drain

spud. It cannot be used in this application.

INSTALL TWO 3/8" WALL ANCHORS (SUPPLIED BY INSTALLER)

WHICH WILL BE USED TO MOUNT THE BOWL TO WALL (SEE

ROUGH-INS ON PAGE 5).

CAREFULLY REMOVE THE SPRAYHEAD COVER (SEE FIGURE 8 ON PAGE 11).

WITH THE HELP OF AN ASSISTANT, CAREFULLY LIFT THE BOWL ONTO THE PEDESTAL FRAME USING

APPROPRIATE LIFTING PROCEDURES. ENSURE BOWL REMAINS 3 – 4 INCHES FROM THE WALL.

INSTALL THE TWO WALL ANCHOR BRACKETS TO THE BACK OF THE BOWL USING THE 3/8"- 16 X 1-1/2" HEX-HEAD BOLTS, 13/32"

I.D. PLAIN WASHERS, ANCHOR PLATES, 3/8" I.D. LOCKWASHERS, AND 3/8"- 16 HEX NUTS PROVIDED AS SHOWN IN FIGURE 4.

UNCOIL THE INFRARED SENSOR LEADS AND PLASTIC TUBING FROM THE REAR OF THE BACKSPLASH.

SLIDE THE BOWL BACK TO THE WALL AND SECURE THE BOWL’S WALL BRACKETS TO THE WALL ANCHORS WITH TWO 3/8" BOLTS

AND WASHERS (SUPPLIED BY INSTALLER).

FASTEN THE BOWL TO THE UPPER BRACKET ON THE PEDESTAL ASSEMBLY WITH THE TWO 1/4"- 20 X 1/2" ROUND-HEAD SCREWS

AND 5/16" I.D. WASHERS SUPPLIED.

INSTALL THE DRAIN SPUD IN THE BOWL USING PLUMBER’S PUTTY (SEE FIGURE 5).

FROM BENEATH BOWL, THREAD THE SPUD WASHER AND SPUD LOCKNUT ONTO THE DRAIN SPUD AND TIGHTEN THE LOCKNUT

AGAINST THE BOWL (SEE FIGURE 5).

INSTALL STRAINER IN THE BOWL DRAIN USING THE TWO #10-24 X 1/2" FLAT SOCKET HEAD SCREWS SUPPLIED.

CONNECT THE DRAIN TRAP (SUPPLIED BY INSTALLER) TO THE DRAIN SPUD AND DRAIN LINE.

MF2944/IR Installation

10 10-28-2005 Bradley Corporation • 215-1180 Rev. R; EN 06-915C

Supply

Inlet

Vernatherm™ Mixing Valve

Solenoid

Assembly

Sensor

Circuit

Plug

Transformer

Circut Plug

Green Supply Tube

(From Sprayhead)

Red Supply Tube

(From Sprayhead)

Black Supply Tube

(From Sprayhead)

Yellow Supply Tube

(From Sprayhead)

Yellow Spade Terminal

Black Spade Terminal

Red Spade Terminal

Green Spade Terminal

White Jumper Terminals

Solenoid Tube Connecto

Figure 6

6Electrical and supply connections

IMPORTANT:

The Adaptive® Infrared control must be connected with a 24 VAC Class II transformer.

Connections to 110 VAC can cause personal injury and will result in damage to the electronics.

CAUTION:

Connection of leads other than shown may cause permanent damage to the sensor.

SNAP THE SENSOR CIRCUIT PLUG FROM THE BOWL INTO THE SOLENOID CIRCUIT PLUG

LOCATED ON THE VALVE BRACKET.

SNAP THE TRANSFORMER CIRCUIT PLUG INTO THE FEMALE TRANSFORMER CIRCUIT PLUG

LOCATED ON THE VALVE BRACKET.

INSERT FOUR DIFFERENT COLORED SPRAYHEAD SUPPLY TUBES INTO FOUR SOLENOID TUBE CONNECTORS, AS

SHOWN IN FIGURE 6, BY LOOSENING TUBE CONNECTOR CAP AND FIRMLY PUSHING TUBING INTO TUBE

CONNECTOR UNTIL THE TUBES ARE FULLY SEATED, THEN RE-TIGHTEN CONNECTOR CAP.

NOTE!

The color of the supply

tubes must match the color

of the colored harness

wires connected to the

valves.

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley S19-260 Bedienungsanleitung

Bradley

Bradley S19-465 Bedienungsanleitung

Bradley

Bradley S96-051 Bedienungsanleitung

Bradley

Bradley MG-2/TT Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley 594 Bedienungsanleitung

Bradley

Bradley Express MG-2/NDT Bedienungsanleitung

Bradley

Bradley S19-120BF Bedienungsanleitung

Bradley

Bradley S19-200B Bedienungsanleitung

Bradley

Bradley S19-120G Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley Express EXD Series Bedienungsanleitung

Bradley

Bradley S19-130SSBF Bedienungsanleitung

Bradley

Bradley S19294 Series Bedienungsanleitung

Bradley

Bradley S19-465EFW Bedienungsanleitung

Bradley

Bradley S19-220DCRPT Bedienungsanleitung

Bradley

Bradley 1C TouchTime Bedienungsanleitung

Bradley

Bradley Express SS-2N/BIR3/STD Bedienungsanleitung

Bradley

Bradley S19-310PVC Bedienungsanleitung

Bradley

Bradley S19-230T Bedienungsanleitung

Bradley

Bradley Verge LVGD Series Bedienungsanleitung

Bradley

Bradley S19-230H Bedienungsanleitung

Bradley

Bradley Terreon Quadra-Fount MF2949/IR Bedienungsanleitung

Bradley

Bradley S19-120P Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema