Bradley Verge LVA Series Bedienungsanleitung

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

215-1849 Rev. C: ECN 19-08-037E

Page 1 of 12 2/26/2020

LVAD1

Verge®Wash Basin – LVA-Series with

Evero®Natural Quartz Material

Table of Contents

Components ......................................................................3

Supplies Required .............................................................4

Dimensions....................................................................4–5

Rough-Ins ......................................................................6–7

Bracket Mounting...............................................................8

Drain Assembly .................................................................8

Faucet and Soap Installation.............................................9

Bowl Mounting ...................................................................9

Strainer and Drain Cap....................................................10

Adjust Temperature..........................................................10

Access Panel...................................................................11

Cleaning and Maintenance..............................................12

LVAD1 Installation

22/26/2020 Bradley • 215-1849 Rev. C: ECN 19-08-037E

WARNING

Make sure that all water supply lines have been flushed and then completely turned off before beginning

installation. Debris in supply lines can cause valves to malfunction.

Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation. Electrical

power MUST remain off until installation is complete.

Installer's hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out

rating of 1,000 pounds.

IMPORTANT

Read this entire installation manual to ensure proper installation. When finished with the installation, file this

manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances

is the responsibility of the installer. Product warranties may be found under “Products” on our Web site at

www.bradleycorp.com.

Separate parts from packaging and make sure all parts are accounted for before discarding any packaging

material. If any parts are missing, do not begin installation until you obtain the missing parts.

For standard height mounting, do not exceed the recommended 33.5" distance from the fixture rim to the

finished floor.

Installation LVAD1

Bradley • 215-1849 Rev. C: ECN 19-08-037E 2/26/2020 3

Components

LVAD1BO

Contact your Bradley

Representative for color options

Individual Rough-In Option

Chrome P-Trap (S29-094)

Plastic P-Trap (269-1697)

Wall Bracket

(140-1153)

TMV Valve

(½" NPTM

Outlet)

(S45-2701)

Hose Prepack

(S45-2730)

Supply

Fittings

(S45-2712)

Hose Prepack

(S45-2702)

Plastic Hose

Plastic

Hose

O-Ring

(125-111)

Drain

Adapter

Packing

Washer

#10-24

Screw

Drain

Adapter

Prepack

(S45-2480)

Access Panel

(186-1911)

Access Panel Bracket

(140-1172)

#10 Access Panel

Thumb Screw

(160-536)

Access Panel Security

Screw Option

(S45-2880)

Trough Strainer

(173-038)

Trough Strainer Screw

(160-353)

Drain Cap

(111-139)

Drain Cap Spacer

(269-2540)

TMV & Tempered Supply Connections

TMV Supply Connections

Two (2) connections

are required for TMV.

Use for faucets not

supplied by Bradley

that require a TMV.

LVAD1 Installation

42/26/2020 Bradley • 215-1849 Rev. C: ECN 19-08-037E

Dimensions (mm)

Top View (shown with Crestt Series Faucet and Soap)

Front View

Supplies Required

• (4) ³⁄₈" fasteners and wall anchors for bowl and wall bracket (minimum pull-out rating of 1,000 lb)

• (4) ¼" fasteners and wall anchors for access panel brackets (minimum pull-out rating of 100 lb)

• ½" hot/cold or tempered stub-out

• 1½" NPT drain stub-out(s)

• OPTIONAL: (1) 110V GFCI protected electrical outlets for 100–120V AC plug-in transformers only

• Screen filter(s) as needed, if not included with faucet(s)

• Drill

• Crescent wrench

• Tape Measure

• Phillips screw driver

• Flat head screw driver

• Level

14³⁄₈"

(366)

21"

(533)

(127)

(152)

20"

(508)

29¾"

(756)

20"

(508)

3¾"

(95)

30"

(762)

Installation LVAD1

Bradley • 215-1849 Rev. C: ECN 19-08-037E 2/26/2020 5

Dimensions – Side View (mm)

ADA/TAS Standard Height

ADA/TAS Juvenile Height (Children 6-12

years)

CSA Standard Height

Dim A 33-1/2" (851mm) 30-1/2" (775mm) 33-1/2" (851mm)

Dim B 27" (686mm) 24" (610mm) 29-29/32" (760mm)

Dim C 13-1/2" (343mm) 10-1/2" (267mm) 13-1/2" (536mm)

Notes

At least one basin must meet

dimensional requirements and have

proper reach, knee, and toe clearance.

At least one basin must meet

dimensional requirements and have

proper reach, knee, and toe clearance.

3¾"

(95)

20"

(508)

21"

(534)

20°

(126)

7½"

(190)

4-1/4"

(107)

6-1/4"

(158)

(178)

13-1/2"

(343)

LVAD1 Installation

62/26/2020 Bradley • 215-1849 Rev. C: ECN 19-08-037E

Mounting for Standard, ADA, and TAS height shown.

Structural Rough-Ins (mm)

Points A, B, and C require sufficient backing

compliant with local building codes.

CODE DESCRIPTION QTY.

A Install (1) 3/8" wall anchor with a minimum pull-out force of 1,000 lb per local codes at locations shown 2

Provide structural backing compliant with local building codes.

Install wall anchor with a minimum pull-out force of 100 lb per local codes at locations shown

RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FIXTURE STYLE

33½" No Adjustment Standard Height, ADA, TAS, and CSA

30½" Subtract 3" Juvenile, ADA, and TAS

Secure bracket to wall using min. 3/8"

anchor bolt to the left of C/L and min. 3/8"

anchor bolt to the right of C/L. The anchor

bolt to the right of C/L must be min. 5"

apart from the anchor bolt to the left of

C/L. When mounting is complete, check

to ensure the bracket is level. See Step 1:

Bracket Mounting for more information.

WARNING The bracket is not designed to support the bowl. Wall bracket is a

temporary support until bowl is mounted at location "A". Ensure

bowl is completely seated in the wall bracket and securely

fastened to the wall at point A.

31-1/2"

(800)

10"

(254)

29-1/2"

(749)

Bottom of

Bracket

Wall Bracket

25-1/4"

(654)

33-1/2"

(851)

9-1/8"

(231)

14-1/4"

(362)

12-5/8"

(320)

12-5/8"

(320)

10"

(254)

10"

(254)

Access

Panel

Bracket

9-1/8"

(231)

3/4"

(19)

Finished Floor

Access

Panel

(127)

2-1/2"

(64)

15-1/8"

(384)

Installation LVAD1

Bradley • 215-1849 Rev. C: ECN 19-08-037E 2/26/2020 7

Plumbing and Electrical Rough-Ins (mm)

Mounting for Standard, ADA, and TAS height shown.

Verge™ deck-mounted soap dispenser and faucet rough-in is shown below.

For rough-in information on the LVAD1 Verge Wash Basin with WashBar Duo,

refer to the WashBar Duo WBD1 tech data.

CODE DESCRIPTION QTY.

A 1½" NPT Drain, Stub-out 2" from wall, individual waste option 1

H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1

E110V GFI protected electrical outlet (AC faucet and soap only)

WashBar Duo requires 120V AC, GFCI outlet properly grounded 1

F #10 Anchors for Faucet Control Box Installation 2

G #10 Anchors for Soap Tank Installation 2

33½"

(851)

2½"

(64)

1½"

(38)

5½"

(141)

3¹⁄₈"

(80)

4¾"

(121)

(152)

⁵⁄₈"

(15)

(102)

Finished Floor

24⁵⁄₈"

(626)

27³⁄₈"

(695)

23¹⁄₈"

(587)

25"

(636) 17⁵⁄₈"

(448)

G G

H C

LVAD1 Installation

82/26/2020 Bradley • 215-1849 Rev. C: ECN 19-08-037E

Bracket Mounting

Typical installation is shown. It may be necessary to repair the wall

after mounting. The fixture may not cover all of the wall modifications.

(127mm)

min.

Install wall bracket to wall

per structural rough-in

dimensions. Check to

ensure the bracket is

level. Example anchor

locations shown.

Mounting height per structural rough-in dimensions.

For ease of drain installation, lay the bowl on its back.

2Drain Assembly

O-Ring

Drain

Adapter

Packing

Washer

#10-24

Screw

Assemble the remaining components as

shown and thread the four screws through

the drain adapter and into the basin inserts.

Ensure the screws compress the drain

adapter evenly onto the basin.

Installation LVAD1

Bradley • 215-1849 Rev. C: ECN 19-08-037E 2/26/2020 9

Bowl Mounting (to Bracket and Wall)

Position bowl above wall bracket.

Press firmly on the back of the bowl

to seat the bowl flange into the wall

bracket lip. Ensure bowl is level.

Secure the bowl to the wall anchors

using fasteners per the structural

rough-in requirement (supplied by

installer).

WARNING Ensure bowl is completely seated in

the wall bracket and securely fastened

to the wall at point A.

Faucet and Soap Installation

CAUTION Bracket is not

intended to support

the weight of bowl

for an extended

period of time. Be

sure to secure the

bowl to the wall

using appropriate

fasteners.

For ease of installation, leave the bowl laying on its back.

See Faucet and Soap installation instructions for assembly.

LVAD1 Installation

10 2/26/2020 Bradley • 215-1849 Rev. C: ECN 19-08-037E

Adjust Temperature with Water Running

ALoosen Cap Screw about 1/4" (4-6

turns) and lift up cover (do not

remove).

BUsing cover, turn cartridge gently until

desired water temperature is reached.

Do not turn past stops as this may

damage unit. Push cover down and

tighten screw.

WARNING This valve is NOT factory

preset. Upon installation,

the temperature of this

valve must be checked and

adjusted to ensure delivery

of a safe water temperature.

Water in excess of 110°F

(43°C) may cause scalding.

Strainer and Drain Cap

Position drain cap over

trough strainer, aligning

tabs into drain. Push

drain cap down until drain

cap is flush with basin.

Grommets should hold

drain cap securely against

drain tough walls.

To remove drain cap,

carefully slip flat

screwdriver into left or

right hand corner of

drain cap and gently lift

upwards.

Front Note Angle of

Drain Cap

Drain cap is labeled front and back. Be sure front is

facing the user. Top surface of drain cap should be

sloped away from user.

Andere Handbücher für Verge LVA Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley SN2003 Kurzanleitung

Bradley

Bradley HN200 Bedienungsanleitung

Bradley

Bradley S19-220ABF Bedienungsanleitung

Bradley

Bradley S45-1964 Bedienungsanleitung

Bradley

Bradley S19-315BF Bedienungsanleitung

Bradley

Bradley Sentry SN2003/TT Bedienungsanleitung

Bradley

Bradley S67-504 Bedienungsanleitung

Bradley

Bradley S19-220SC Bedienungsanleitung

Bradley

Bradley Navigator S19-2010 Series Bedienungsanleitung

Bradley

Bradley Verge LVQ Series Bedienungsanleitung

Bradley

Bradley S19-310DCFW Bedienungsanleitung

Bradley

Bradley S19-120P Bedienungsanleitung

Bradley

Bradley S19-210FW Bedienungsanleitung

Bradley

Bradley Express EXD Series Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley S19-280 Series Bedienungsanleitung

Bradley

Bradley LC800 Bedienungsanleitung

Bradley

Bradley MG-2/TT Bedienungsanleitung

Bradley

Bradley S19-230 Bedienungsanleitung

Bradley

Bradley Terreon Quadra-Fount MF2944/IR Bedienungsanleitung

Bradley

Bradley Express ELX Series Bedienungsanleitung

Bradley

Bradley HN-400 Bedienungsanleitung

Bradley

Bradley S19-125SBF Bedienungsanleitung

Bradley

Bradley EXPRESS SS-3/AST/JUV Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema