Bristan PIV BAS C Bedienungsanleitung

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave them

with the user.

Installation Instructions

Pivot Tap Range

Models covered:

PIV BAS C, PIV SABAS C,

PIV 1HBF C

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert.

We have designed this product with your enjoyment in mind. To ensure that it works

to its full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and, if you need any further help,

please do not hesitate to contact us.

Important Safety Information................................................... 3

General Information ................................................................. 4

Speciﬁcations ........................................................................... 5

Dimensions............................................................................... 6-7

Installation Requirements ....................................................... 8

Installation................................................................................ 9

Maintenance ............................................................................. 10

Map of Hard Water Regions ..................................................... 11

Troubleshooting........................................................................ 12

Notes......................................................................................... 13

Guarantee ................................................................................. 14-15

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are

installed, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this product safely you must

employ the services of an experienced qualiﬁed plumber.

•This product needs to be installed in accordance with, and meet the requirements of

the Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

•Remove all packaging and check the ﬁtting for damage before starting installation.

•Warning: Before starting any installation please consider the following: before

drilling into walls, check that there are no hidden electrical wires, cables or water

supply pipes. This can be checked with the aid of an electronic detector.

•If power tools are used do not forget to: - Wear eye protection

- Unplug equipment after use

•Important: Remember to turn off the mains water supply before connecting to any

existing pipe work. Fitting isolating valves to the inlet feeds is recommended for ease

of maintenance.

•Warning: Before installing this product it is essential that you thoroughly ﬂush

through the pipework in order to remove any remaining swarf, solder, etc.

Failure to carry out this procedure could cause problems or damage to the workings of

the tap.

•Take care when handling the ‘ﬂexible connecting pipes’, do not bend, twist or crush

them. Only tighten the pipes by hand.

•This product must not be modiﬁed in any way as this will invalidate the guarantee.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

General Information

This product has been tested to the Water Regulations Advisory Scheme (WRAS) and

satisﬁes the requirements of the Water Supply (Water Fittings) Regulations 1999 and

current bylaws. For full Installation Requirements & Notes (IRN) please visit

www.wras.co.uk/directory.

Designed to comply with BS EN 200 for combination taps to be used within systems

designed to BS 8558.

BS 8558 recommends hot water should be stored and distributed at a temperature of

not less than 60°C which will help minimise the buil-up of lime scale in hard water

areas.

If installing this product on a low pressure (tank fed) system please see speciﬁcations

table on page 5 to determine the minimum distance required from undeside of the cold

water tank to the outlet.

These taps and mixers should be installed in compliance with the Water Regulations.

Where the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the

mains, approved check valves must be ﬁtted in the supply pipes.

For further details contact your Local Water Authority.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Speciﬁcations

Product Code

Working pressure

Inlet

Minimum

distance from

cold water tank to

outlet (metres)

Min Max

PIV BAS C 0.2 5.0 M12 15mm Plain Flexible Tails 2

PIV SABAS C 1.0 5.0 M12 15mm Compression Flexible Tails 10

PIV 1HBF C 1.0 5.0 M12 22mm Compression Flexible Tails 10

Maximum static pressure- 10.0 bar

System Requirements:

Gravity fed hot & cold (Equal pressures)

Gravity fed hot & cold (Differential pressure, maximum ratio 5:1)

Unvented systems

Instantaneous water heater (Combination boiler)

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dimensions

Dimensions are approximate and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

106

128

355

Basin Mixer

1 Hole Bath Filler

150

338

131

Dimensions Cont.

Dimensions are approximate and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

1 Hole Basin Mixer (Side Action)

112

100

382

Installation Requirements

Flexible Connecting Pipes

Care must be taken when connecting the ﬂexible connection pipes to the household pipework to

ensure they do not bend sharply and kink or twist.

See below for recommended ways to ﬁt the ﬂexible connecting pipes.

Slight

bend

90°

Angle

Kink Curved

round

Twists

Important: Failure to follow these guidelines may result in poor performance and damage

to the ﬂexible connecting pipes.

Important: Full access must be made available on installation for future maintenance/

servicing purposes.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Installation

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

1. Screw the ﬂexi tails into the bottom of

the mixer body / bath ﬁller by hand only

(DO NOT OVERTIGHTEN).

2. Feed the ﬂexi tails through the hole in

the basin/bath, ensuring the washer is

ﬁtted between the body and the basin/

bath to create a water tight seal.

3. Screw the ﬁxing rod into the bottom

of the tap. Slide the 'C' shaped rubber

washer and 'C' shaped metal washer onto

the ﬁxing rod up to the underside of the

basin/bath.

4. To secure the mixer/bath ﬁller in place

tighten the ﬁxing nut onto the ﬁxing rod

until it is fully tightened against the

'C' shaped metal washer. The ﬁxing nut

can be tightened with a suitable spanner.

5. Connect the ﬂexi tails to the hot and

cold water supplies.

6. Turn on both water supplies, fully open

both valves, letting the water run for a few

minutes to ﬂush out the system.

7. Fit the clicker waste (basin mixer only)

ensuring the rubber washer is ﬁtted

between the basin and the waste. Place

the other rubber washer under the basin

and secure by tightening the backnut, in

order to ﬁll the basin, the button in the

middle of the waste needs to be pressed

down. To release the water, press the

button again.

8. Check all joints and connections for any

leaks.

Maintenance

Your product has a high quality ﬁnish

and should be treated with care to

preserve the visible surfaces. All

surfaces will wear if not cleaned

correctly, the only safe way to clean your

mixer is to wipe with a soft damp cloth.

Stains can be removed using washing

up liquid. All bath cleaning powders and

liquids will damage the surface of your

ﬁtting, even the non-scratch cleaners.

Note: Never use abrasive detergents

or disinfectants or those containing

alcohol, hydrochloric acid or phosphoric

acid.

Before carrying out any maintenance,

turn off the both water supplies or close

any isolating valves.

Remove the cap, loosen the grub screw

using a 2.5mm hexagonal key. Remove

the handle, shroud and cartridge

retaining nut. Remove the cartridge.

Clean the cartridge thoroughly under

cold water to remove any build up of

limescale or debris.

If necessary replace the cartridge using

parts supplied by Bristan only.

Replace the cartridge into the body.

Replace the cartridge retaining nut,

shroud and the handle. Tighten the grub

screw and push ﬁt the cap.

Cleaning the Cartridge

General Cleaning

2.5 mm hexagonal

key

Grub Screw

Handle

Shroud

Cartridge Retaining Nut

Cartridge

Tap Body

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Cap

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan Wine Easyfit Verdrahtungsschema

Bristan

Bristan TG SNK C Verdrahtungsschema

Bristan

Bristan Moloko Bedienungsanleitung

Bristan

Bristan KN2 SHXAR C Montageanleitung

Bristan

Bristan W BATH05 C Verdrahtungsschema

Bristan

Bristan W BASIN13 C Verdrahtungsschema

Bristan

Bristan CART 06734B Original Betriebsanleitung

Bristan

Bristan Artisan AR2 SHXMTFF2 C Montageanleitung

Bristan

Bristan W-BASIN01-C Verdrahtungsschema

Bristan

Bristan PISA PS2-BSM-C Bedienungsanleitung

Bristan

Bristan Java J BASNW C Bedienungsanleitung

Bristan

Bristan RV SNK C Bedienungsanleitung

Bristan

Bristan DSC SHC3DIV C Verdrahtungsschema

Bristan

Bristan GLL RAPSNK4 C Bedienungsanleitung

Bristan

Bristan CART 06732COMPL Original Betriebsanleitung

Bristan

Bristan IRBS4-CP Montageanleitung

Bristan

Bristan CRZ SHXDIVCTFF C Verdrahtungsschema

Bristan

Bristan AR2 SHXVOFF Montageanleitung

Bristan

Bristan SOQ2 SHUAR C Montageanleitung

Bristan

Bristan VAL2 BAS C CD (D2) Verdrahtungsschema

Bristan

Bristan Rio Bedienungsanleitung

Bristan

Bristan JAVA J BSM E8 C Bedienungsanleitung

Bristan

Bristan Java Eco Click J EBAS C Bedienungsanleitung

Bristan

Bristan W BASIN08 C Verdrahtungsschema

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung