Broseley Q7 Handbuch

200747_1

Installation & Operating Instructions

Model: Gas Q7

Variants Covered: Ignite (CD1), Hereford (CD2) &

Desire (SD1)

Conventional Flue Natural Gas Stove

Top Flue Outlet Only

PLEASE LEAVE THESE INSTRUCTIONS WITH THE END USER

Chimney closure plates are not supplied

Please note gas installations MUST only be carried out by installers who

are Gas Safe registered.

200747_1 2

Contents

Introduction 3

Packing List 3

Specification 4

Dimensions 4

Hearth Requirements 5

Chimney Requirements 6

Assembly

Burner Installation 7

Mica Board Installation 8

Connecting the TTB Sensor 9

Fitting the Decorative log retainer 9

Positioning the logs 10-13

Gas Connection & Pressure Testing 14

Spillage Testing 15

Maintenance 16

Operating the Stove 17

Cleaning the Stove 18

Curing the Paint 18

Trouble-shooting 19

Servicing 20

Commissioning Form 21

Guarantee 22

Notes 23

200747_1 3

Introduction

THANK YOU FOR PURCHASING A BROSELEY GAS STOVE

Broseley Fires Ltd, a family run company, was founded as an appliance and

design development company in 1975.

Since then we have built up an enviable reputation for the quality, reliability and

fuel efficiency of our stoves.

These instructions have been carefully prepared to guide the installer and end-

user through the relevant methods and standards for installation of your new Gas

Stove.

Correctly installed and operated, your stove will give you many years of warmth

and reliability. Therefore, we would suggest that you read the whole instruction

manual prior to handing it to your installer. That way you will have a clearer

picture of what is involved.

It is required by law that the complete assembly, installation and commissioning

of gas stoves is carried out by a professionally qualified and accredited gas fitter

listed on the “Gas Safe” register.

THE INSTALLATION MUST BE IN ACCORDANCE WITH THE ‘GAS SAFETY

INSTALLATION AND USE REGULATIONS’ IN CONJUNCTION WITH THESE

INSTRUCTIONS AND THE RELEVANT ‘BRITISH STANDARDS CODES OF

PRACTICE’ REQUIREMENTS AND THE RELEVANT ‘LOCAL AND NATIONAL

BUILDING REGULATIONS’. A COMMISSIONING CERTIFICATE MUST BE

LEFT WITH THE END CUSTOMER UPON FINAL COMPLETION AND THE

COMMISSIONING FORM COMPLETED IN THE BACK OF THESE

INSTRUCTIONS.

Packing List

Stove Box Fibre Box 1 (Packed In Stove)

1 x Stove body 1 x Large rear coal matrix

1 x Flue spigot 2 x Front log matrix’s

1 x Burner (Attached) 2 x Side cheeks

1 x Instruction Manual

1 x Left hand side mica board (Attached) Fibre Box 2 (Packed outside Stove)

1 x Right hand side mica board (Attached) 9 x Loose logs

1 x Rear mica board (Attached)

1 x Top mica board (Attached)

3 x M6 x 30 Bolts

3 x M6 Washers

200747_1 4

Specification

Heat Input (Gross) 6.8kW

Gas Category I2H

Supply Pressure 20 mbar

Gas Rate 0.66 m3/hr

Injector Size 77

Flue diameter 125mm (5”)

Country of destination GB, IE

Efficiency Class Class 2

Nominal Output 4.7kW

NOx Class 3

Please note this product is designed to only use natural gas G20.

Dimensions

Ignite CD1 Q7 - WEIGHT 75 Kg

Hereford CD2 Q7 –WEIGHT 68 Kg

Desire SD1 Q7 –WEIGHT 71 Kg

All dimensions are in millimetres.

The front, sides and top are considered working areas of the appliance.

Ignite

CD1

Hereford

CD2

Desire

SD1

542

565

542

582

608

582

288

285

288

162

165

162

345

342

345

200747_1 5

Hearth Requirements

The appliance needs to be located onto a solid non-combustible hearth with a

minimum thickness of 12mm. The hearth must be capable of withstanding the

weight of the appliance.

To ensure correct combustion the following minimum clearances must be

adhered to

NB Measurements taken from the Lid of the stove (Dimension C on page 4):

Material

Dimension

Rear

Non-Combustible

100mm

Side

Combustible

150mm

Non-Combustible

150mm

Hearth Protrusion (in front of the appliance) 50mm

Shelf Distance 300mm

Please note these are minimum clearances, whenever possible it is advisable to

have as much clearance as possible around the stove for easy access and

maintenance.

Please note the gas supply connection to the appliance is to the right hand

side rear of the stove. The connection requires an 8mm-diameter semi-rigid

pipe, not more than 1 meter in length.

Additional Requirements

Curtains should not be positioned above the appliance at a distance of

less than the minimum specified for shelves

An additional guard is to be used to take account of the special hazards

that exist in nurseries and other places where there are young children or

aged or infirm persons present.

200747_1 6

Chimney Requirements

Please note Broseley Fires do not provide flue pipes, closure plates or any

other associated accessory.

Top Flue Outlet Only

The stove must be installed in accordance with current gas and buildings regulations

BS5871: Part1. The appliance can be installed in any adequate area suitable for

solid fuel fires and stoves. It can use a class 1, class 2 and pre-cast flue.

For pre-cast flue installations it is ESSENTIAL that a sealed connection is made into

the actual flue system (a void behind a closure plate is not permitted). Please refer to

the codes of best practice for further advice on pre-cast flues. Before you install the

stove, make sure the chimney flue outlet is correctly positioned to align with the flue

outlet on the stove and that the chimney is in good condition. If not, a chimney liner

must be installed or a suitable class II gas flue used. A draught is necessary to

ensure the products of combustion are fully evacuated.

Ideally it is recommended that the flue run is as straight as possible. The flue

must have a minimum vertical height of 3 metres to insure adequate draught.

You can have a maximum of four bends in the run, each bend must not exceed

45° and an additional metre of vertical flue should be provided for each bend.

Ideally you should have a minimum vertical section of 600mm before any bend

immediately off the top of the appliance, however it is permitted to use a 45°

bend straight off the appliance provided you have an adequate flue draft.

Prior to installation, the installer should insure that the flue is free from obstruction

and any dampers must be fixed in a permanently open position. Ensure the chimney

is not closed and that it has been swept and subsequently smoke tested.

Make sure that rain, birds or any foreign body cannot get into the chimney to cause

damage or blockage. This problem can normally be overcome by fitting an approved

gas cowl. It is essential for the effective running of your stove that the chimney draws

properly to allow the products of combustion to escape.

VENTILATION (GB ONLY)

The gas stove is rated at less than 7kw and therefore does not normally require

additional ventilation in the room (BS5871 –part II).

Flue Spigot Connection

Attach the supplied spigot to the top of the stove using the three M6x40 bolts and

washers provided.

200747_1 7

Assembly - Burner Installation

Ensure all components are present prior to commencing assembly (See Packing

List on page 3). You will need a pozi drive screwdriver.

1) Remove the stove body from its packaging and stand it in position.

2) Open the main door.

3) Insert the burner end with the control knob first followed by the other end of the

burner locating the burner bracket onto the side fixing points.

4) Fasten the burner into position using two (2) M6x40 bolts and washers provided.

5) The stove base plate can now be fitted. This plate rests on the base on the stove

6) Next fit the mica boards as detailed in the next section.

200747_1 8

Assembly –Mica Boards

First fit the rear mica board behind the burner bracket as shown above and

secure through the burner fixing points using the 2 x No.6 x 25 self -tapping

screws provided.

Now fit one of the side mica boards Next rest the top mica board onto

ensuring that the board is snug the side board (this board will

between the front of the stove and need supporting whilst the final

the rear mica. Side board is fitted.

Finally fit the remaining side mica board and

allow the top board to rest down onto it (the

top board should bow be supported by both

the side and rear mica boards).

200747_1 9

Assembly - Fitting TTB sensor

With the burner installed, thread the wires from the interrupter to the TTB device

(mounted on the rear panel of the stove). These wires can be installed either way

round on the terminals.

200747_1 10

Assembly –Decorative Log Retainer

Using the 2 off M6 Nut and Bolts provided, locate the decorative trim behind the

stove opening as shown and secure in position.

Inhaltsverzeichnis

Andere Broseley Herd Handbücher

Broseley

Broseley Snowdon 30 Handbuch

Broseley

Broseley 12B Handbuch

Broseley

Broseley YORK Bedienungsanleitung

Broseley

Broseley Desire Handbuch

Broseley

Broseley York Midi SE Handbuch

Broseley

Broseley Evolution Endure Installationsanleitung

Broseley

Broseley York Petite Bedienungsanleitung

Broseley

Broseley WINCHESTER Bedienungsanleitung

Broseley

Broseley Gas Q7 MK2 Handbuch

Broseley

Broseley York Midi Bedienungsanleitung

Broseley

Broseley Evolution 5 Multi-fuel Handbuch

Broseley

Broseley IGNITE 5 CD1 MK2 Handbuch

Broseley

Broseley eVolution Montageanleitung

Broseley

Broseley YORK Bedienungsanleitung

Broseley

Broseley Ignite 5 Handbuch

Broseley

Broseley York Midi Bedienungsanleitung

Broseley

Broseley evolution Ignite 5 Widescreen Handbuch

Broseley

Broseley WINCHESTER Bedienungsanleitung

Broseley

Broseley Ignite 5 Handbuch

Broseley

Broseley Canterbury PD-08-002 Bedienungsanleitung

Broseley

Broseley York Grande Bedienungsanleitung

Broseley

Broseley York Midi Handbuch

Broseley

Broseley Lincoln Handbuch

Broseley

Broseley Canterbury Handbuch

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung