CB2 SHAKE TALL CHEST Bedienungsanleitung

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

Made in Vietnam - r03 Page 1 of 6

shake

TALL CHEST

Thank you for purchasing the Shake Tall Chest. This

page lists all the contents included in the box. Please take

the time to identify the hardware as well as the individual

components to this product. As you unpack and prepare

for assembly, place the contents on a carpeted or padded

area to protect them from damage.

Note: 2 people are recommended to safely assemble this product.

components

assembly hardware

mounting hardware

tools required

4 - plastic

anchors

4 - small

screws

4 - large

screws

4 - mounting

brackets

2 - wall

straps

Missing hardware? Please call 800.606.6387 for replacements.

phillips head screwdriver

(We recommend the use of hand tools instead of power tools)

1 - top panel

1 - center panel

4 - drawer fronts

1 - back panel

1 - bottom panel

2 - side panels

(1 left, 1 right)

4 - drawer bottoms

12 - wood

dowels

12 - bolts 32 - screws

8 - drawer sides

(4 left, 4 right) 4 - drawer backs

1 2

Insert 2 wood dowels into left and right side

panels as shown.

Insert 4 wood dowels into top and bottom panel.

shake

TALL CHEST

Made in Vietnam - r03 Page 2 of 6

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

bottom

panel

left and right

side panels

top

panel

With assistance of another adult, fit dowels of left and right

side panels into corresponding holes of center panel and

attach with 4 bolts. Secure, but do not over tighten, bolts

with a phillips head screwdriver.

left side

panel

right side

panel

Note: Do not over

tighten the bolts

center

panel

5 6

With assistance, position unit upright. Insert back

panel into corresponding grooves of assembly.

Fit dowels of top panel into corresponding holes of

assembly and attach with 4 bolts.

Fit dowels of bottom panel into corresponding

holes of assembly and attach with 4 bolts.

shake

TALL CHEST

Made in Vietnam - r03 Page 3 of 6

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

bottom

panel

back

panel

top

panel

9 10

Attach drawer back to left drawer side with 2

screws.

Attach right drawer side to drawer assembly with

4 screws.

Repeat steps 7-10 for remaining drawers.

7 8

Attach left drawer side to drawer front with 2

screws. Secure, but do not over tighten, screws

with a screwdriver.

Fit drawer bottom into corresponding grooves of

drawer assembly.

shake

TALL CHEST

Made in Vietnam - r03 Page 4 of 6

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

drawer front

left drawer

side

drawer

bottom

drawer

back right drawer

side

Fit drawer glides of each drawer into

corresponding drawer glides of case assembly.

Make sure drawer glides securely engage.

Assembly is now complete.

shake

TALL CHEST

Made in Vietnam - r03 Page 5 of 6

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

drawer

assembly

cleaning and care

Clean surfaces with a dry or damp soft cloth. Do not

use abrasive cleaners.

NOTE: Make sure glides are pulled

out of the case and ball bearings are

at the front of the extended glides.

To prevent damage to glides, keep drawer

assembly level during installation.

For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe

mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.).

Mount to wood studs whenever possible.

NOTE: If you are unsure about your wall type or what mounting method you should use, consult a

qualified professional or your local hardware store.

A. Attach 2 brackets to the top of the assembled unit with 2 small screws per bracket.

B. With the assistance of another adult, place the unit in desired location against the wall. Mark the

location of the hole in the bracket on the wall. Move the unit out of the workspace.

C. Drill holes slightly smaller in diameter than the anchors. Insert 1 plastic anchor into each hole until

they are flush to the wall.

D. Insert 2 large screws through each bracket and plastic anchor. Secure, but do not over tighten

with a phillips head screwdriver.

E. Place the unit back into position against the wall and thread the wall strap through both brackets

and pull until tight.

Wall mounting assembly is now complete.

optional wall mounting instructions

shake

TALL CHEST

Made in Vietnam - r03 Page 6 of 6

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

Inhaltsverzeichnis

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung