Child Craft Denman F33601 Bedienungsanleitung

SINGLE DROPSIDE CRIB

CONVERTS TO DAYBED OR

FULL SIZE HEADBOARD

CHILD CRAFT INDUSTRIES, INC.

P.O. Box 444, Salem, IN USA 47167-0444

PH:812-883-3111-FAX: 812-883-1819 - http://www.childcraftindustries.com

ASSEMBLY DIRECTIONS AND PARTS LIST

ΦΦ

ΦREADALLINSTRUCTIONSWITH CAREBEFORE STARTING THEASSEMBLY PROCEDURE.

ΦΦ

ΦYOU WILL NEED A PHILLIPS SCREWDRIVER, A STANDARD SLOTTED SCREWDRIVER, A 3/8” & 7/16” WRENCH

(or adjustable wrench), AND THE ENCLOSED ALLEN WRENCH K.

PARTS ENCLOSED IN HARDWARE BAG

(

NOTED

WHEN

SHOWN

ACTUAL

SIZE

)

AB DE

(4) F/HPhillips

Wood Screw

(actual size)

(4) Hexhead

Machine Screw

(actual size)

(2) 4-Position Spring Bracket

(1)

Lower

Track

Assembly

(Right)

(4) Allenhead K-D Bolts

(actual size)

(2) Upper Tracks

(actual size)

(4) K-D Bolt Plugs

(actual size)

(2) Rubber

Washers

(2) Combo

Machine

Screw

(10) Combo Pan Head

Wood Screw

(4) Insert

Locknut

(4) Hole

Button

Covers NO

(1) Sta-Bar Bracket - Left

PREPARATION

Carefully remove and lay out all hardware and parts. Check quantities and match the Hardware List and the Parts List. NOTE: During

the assembly process whenever using screws or bolts, check each with the Hardware List by letter and size identification.

Place each screw or bolt on the diagram of the item which is sketched actual size. Be sure to use the proper size specified in

the assembly directions. If a part is missing or broken contact your Child Craft dealer or Child Craft, P.O. Box 444, Salem, IN 47167-

0444 USA, 812-883-3111, http://www.childcraftindustries.com for replacement part(s) or instructional literature. Before making this

contact identify your Crib’n’Double Bed by the model identification number stamped on the inside face or bottom edge of the

Headboard, Footboard or crib sides,

or stamped on a label attached to the inside face of Footboard V bottom rail.

Make note of all

identification numbers and include this information with your request. DO NOT SUBSTITUTE PARTS!

Recordyourmodelidentificationnumberherefor futureidentification: Model#______________________________________

(1) Allen Wrench

(4) PhillipsPan

HeadMachine

Screw

(actual size) (actual size)

child craft

(1) Sta-Bar Bracket - Right

H00745:11/01

(actual size)

C(1) Hexhead Wrench

(1)

Lower

Track

Assembly

(Left)

PARTS ENCLOSED IN CARTON

Y (1) Spring

T (1) Stationary Side U (1) Drop Side

V (1) Footboard X (1) Headboard

S (1) Stabilizing Bar

(Sta-Bar)

STEP 1-DIAGRAM 1:ATTACH HARDWARE TO FOOTBOARD AND HEADBOARD

H00745:11/01

plastic pouch

(HELPFUL HINT: Hardware installation may be

easier if the Footboard

and Headboard

are

placed in a horizontal position on a soft surface being careful not to scratch the crib finish).

Install Upper Track Jto the Footboard Vand the

Headboard Xusing two F/H Phillips Wood Screws Aas shown. Attach 4-position Spring Brackets Pusing three Combo Pan Head Wood Screws

Eas shown.

Mount

Lower Track Assembly Right Fto Footboard V. Start by installing a Combo Pan Head Wood Screw into the holes on Lower

Track Assembly Right F, through the holes in

Sta-Bar Bracket - Right

O, and into the pilot holes in Footboard Corner Post V. Tighten securely.

Follow the same procedure to attach Lower Track Assembly Left Gand Sta-Bar Bracket Left Nto Headboard Corner Post X. NOTE: Open slot

at top of Lower Track assembly F& Gfaces the inside of your crib. Install hardware exactly as illustrated.

NOTE: All wood screws have factory bored pilot holes to start the screws (pilot holes are shown in diagrams).

(style may vary)

PILOTHOLES PILOTHOLES

Closed end of

Upper Track J

SEE ENLARGED VIEW

PILOTHOLES

Slot faces

inside of crib

ENLARGED VIEW

STEP 3-DIAGRAM 3:ATTACH STABILIZING BAR TO HEADBOARD AND FOOTBOARD

STEP 2 - DIAGRAM 2: ATTACH STATIONARY SIDE Attach StationarySide Tto HeadboardXand FootboardV.

Inserteach ofthe four

Allenhead K-D Bolts Hinto receiving holes located in corner posts of Stationary Side

H00745:11/01

Tasshown. PlaceStationary Side

Tinalignment andallow K-DBoltsHtocontinue intoends oftopandbottomrails of HeadboardXandFootboard

V. Insert each of the four K-D Bolt Plugs Las shown. Pull out each K-D Bolt Hjust enough to allow the K-D Bolt Plug Lto be fully inserted in hole.

Tighten all four K-D Bolts Huntil secure using Allen Wrench K

while securing K-D Bolt Plugs Lwith a Standard Slotted Screwdriver. CAUTION:

DONOTOVERTIGHTEN.

Mount the Stabilizing Bar Assembly Sto

Footboard Vand Headboard X. With the

Footboard Vin a vertical position, insert (2) Phillips Pan Head Machine Screws Dthrough the holes in

Sta-Bar Bracket - Right

O, and through the

holes in Stabilizing Bar S. Attach (2) Insert Locknuts Ito Machine Screws Dand tighten securely. See Enlarged View for the proper

installation of Locknut I. Follow the same procedure for attaching Stabilizing Bar Sto Headboard X.

Connected View

SEE ENLARGED VIEW

ENLARGED VIEW

NorO

Plastic insert on

Lock Nut I

Locate "Tabs" on Crib Spring Yand rotate

Tabs upward to the approximate angle

shown. Lower Spring Yinto crib being

carefulnottodamagethecribfinish. Position

the (4) Tabs attached to ends of Crib Spring

Y to mount to a selected position in the 4-

Position Spring Brackets Pmounted on

endsVandX. Installa HexheadMachine

ScrewBthrough the(4) CribSpring Tabs

and into a receiving hole in each 4-Position

Spring Bracket Pthen tighten securely

with a 3/8” wrench. Follow the same pro-

cedure when changing spring height at a

laterdate.Check HexheadMachineScrews

Bperiodically and tighten if needed.

STEP 4-DIAGRAM 4:INSTALL SPRING

STEP 5 - DIAGRAM 5: INSTALL DROPSIDE

Align Plastic Guides

(Factory installed) on

Dropside Uwith

dropside hardware

mountedon postfrom

underneath. An as-

sistant is very help-

ful. Afterallfour plas-

tic guides are aligned

with the hardware,

liftDropside“UP” and

allow it to latch into

the raised position.

After Dropside Uis

installed on the

tracks and is latched

in the “UP” position,

insert a Combo Ma-

chine Screw Rinto

a Rubber Washer Q

and thread into hole

in bottom of Lower

TrackAssembliesF

&G.

TO LOWER DROPSIDE

U: FIRST - LIFT THE

DROPSIDE, SECOND -

WITH KNEE PUSH IN ON

CENTER OF BOTTOM

RAIL OF DROPSIDE TO

RELEASE LATCH ON

LOWER PLASTIC LATCH.

LOWER DROPSIDE BY

HAND. TO RAISE

DROPSIDE U: PULL

“UP” UNTIL LOWER

PLASTIC GUIDES LATCH

IN SLOT IN LOWER

TRACKSF& G.ALWAYSBE SURECRIBSIDE IS“UP”AND “LATCHED”BEFORELEAVINGCHILDIN CRIB.

4H00745:11/01

Highest mattress position

Lowest mattress position

Corner post of Vor X

Mattress side of Spring Y

NOTE: Mount all four “Tabs” on Crib Spring YY

at the same vertical mattress position.

TAB

Align Upper

PlasticGuide

with Upper

Track J

Align Lower

PlasticGuide

with Lower

Track F

LOCKING MECHANISM

NOTE: It may be necessary to Flex the Locking Mechanism toward

outside of crib to engage the Lower Tracks FF

F& GG

Align all four plastic guides with installed

tracks from underneath - then lift “UP” until

Lower Plastic Guides latch.

Corner Post of V

DIRECTIONS FOR CONVERTING

“CRIB”TO A“DAYBED”

When use as a crib has been completed, by removing the

Dropside, you have the option to convert to a daybed for years of

additional use in your child’s room. Refer to Step 5 - Diagram 5

and follow directions in reverse order. Store the removed parts

and hardware in the event you wish to convert your daybed back

to a crib. Refer to Sketch A.

WHENEVERDISASSEMBLINGYOURCRIB,DONOTREMOVEANY

ITEMS ATTACHED WITH WOOD SCREWS A OR E!

Sketch A

(style may vary)

MAINTENANCE OF YOUR CHILD CRAFT CRIB/DAYBED: Upon completion of assembly be sure all screws, bolts and fastening devices have been

tightened securely. A frequent check should be made of all screws, bolts and fastening devices and tightened if needed. Before each usage or

assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib if parts are missing or broken. Contact

your Dealer or Child Craft (812) 883-3111, for a replacement part or instructional literature if needed. Include Model Identification Number with your

request which you recorded on page 1 of these instructions. DO NOT SUBSTITUTE PARTS. DO NOT MAKE ANY ALTERATIONS NOT DESCRIBED

INTHESE ASSEMBLY DIRECTIONS.

CLEANING INSTRUCTIONS FOR YOUR CHILD CRAFT CRIB/DAYBED: Mix together a mild solution of gentle dishwashing liquid and water, apply to

surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth, then dry all surfaces thoroughly

with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE

FURNITURE.

STORAGE AND USE OF YOUR CHILD CRAFT CRIB/DAYBED: A printed plastic pouch is attached to the crib spring for the permanent storage of the

assembly directions. After completing the assembly process you are advised to read and be aware of all WARNINGS, CAUTIONS, CLEANING,

STORAGE, USE AND MAINTENANCE notices contained in this set of directions and printed on the plastic pouch located on the underneath side of the

crib spring. You will then place the complete set of assembly directions into the plastic pouch for future referral. We caution you not to place excess

hardware in the plastic pouch as it could present danger to a child if retrieved. When storing crib use CAUTION as extreme temperature or humidity

changes could be harmful. Use CAUTION when a vaporizer is in use, always aim vapor stream away from crib as well as away from any wood

furniture item.

DIRECTIONS FOR CONVERTING

TO AFULL SIZE HEADBOARD

Disassemble crib by performing

Steps 5, 4, 3 & 2 in reverse order to

remove the Stationary Side T from

the other crib parts. Store assembled

parts carefully for future re-assembly

as a Crib. Attach the Stationary Side

toa Hollywoodstylefull size bedframe

at the location of the mounting cleats

(Hardware is not provided). Insert the

Hole Button Covers Mas shown.

H00745:11/01

Receiving holes for

Hole Button Covers M

Receiving holes for

Hole Button Covers M

Mounting Cleats

(Cleats are flush with the face that the

purchased Hollywood Frame mounts to)

Purchased Mattress

(see size requirements on

page 6 under CAUTION)

(style may vary)

6WARNING

ΦΦ

ΦFAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY IN-

STRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

ΦΦ

ΦREAD ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP

INSTRUCTIONS FOR FUTURE USE. A PLASTIC POUCH IS ATTACHED TO

CRIBFORPERMANENTSTORAGEOFTHEINSTRUCTIONALLITERATURE.

ΦΦ

ΦBEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR

DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR

SHARP EDGES. DO NOT USE CRIB IF ANY PARTS ARE MISSING

OR BROKEN. ASK YOUR DEALER OR WRITE TO CHILD CRAFT,

P.O. BOX 444, SALEM, IN 47167-0444 USA (812)-883-3111), http://

www.childcraftindustries.com FOR REPLACEMENT PARTS AND

INSTRUCTIONAL LITERATURE IF NEEDED. INCLUDE MODEL IDENTIFI-

CATION NUMBERS WITH YOUR REQUESTWHICHYOURECORDEDON PAGE ONE. DO

NOT SUBSTITUTE PARTS.

ΦΦ

ΦAFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE.

ΦΦ

ΦWHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE

HEIGHT OF 35 INCHES (90 CENTIMETERS) THE CRIB SHALL NO

LONGER BE USED.

ΦΦ

ΦDO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM

BLINDS OR DRAPES MAY STRANGLE A CHILD.

ΦΦ

ΦIF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR

CHILDREN’S PRODUCTS.

ΦΦ

ΦDO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE

SIDE IS IN RAISED AND LOCKED POSITION WHENEVER CHILD

IS IN CRIB.

ΦΦ

ΦWHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET

MATTRESS TO LOWEST POSITION AND REMOVE BUMPER PADS,

LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS

STEPS FOR CLIMBING OUT.

ΦΦ

ΦNEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC

FILM AS MATTRESS COVERS BECAUSE THEY CAN CAUSE SUF-

FOCATION.

ΦΦ

ΦDO NOT USE A WATER MATTRESS WITH THIS CRIB.

ΦΦ

ΦREPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE. (IF

EQUIPPED WITH TEETHING RAILS.)

ΦΦ

ΦSTRINGS CAN CAUSE STRANGULATION! DO NOT PLACE

ITEMS WITH A STRING AROUND A CHILD’S NECK, SUCH AS

HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND

STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.

ΦΦ

ΦREMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB

AREA WHEN YOUR CHILD IS BEGINNING TO PUSH UP ON HANDS

AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER OCCURS

EARLIEST. THESE TOYS CAN CAUSE STRANGULATION.

ΦΦ

ΦWHENDISASSEMBLING THISCRIB, DO NOT REMOVE ANYITEM

ATTACHED WITH WOOD SCREWS.

ΦΦ

ΦALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY

CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE

CRIB, THAT EVERY COMPONENT IS PROPERLY AND SECURELY

IN PLACE.

CAUTION

ΦΦ

ΦANY MATTRESS USED IN

THIS CRIB MUST BE AT

LEAST 27-1/4 INCHES (69

CENTIMETERS), BY 51-5/8

INCHES (131 CENTIME-

TERS), WITH A THICKNESS

NOT EXCEEDING 6 INCHES

(15 CENTIMETERS).

THEDIMENSIONSOF THEMATTRESS

SHALL BE TAKEN FROM SEAM TO

SEAMOR EDGETOEDGE WHEREAP-

PROPRIATE.

ΦΦ

ΦUPON COMPLETION OF

ASSEMBLY BE SURE ALL

SCREWS, BOLTS AND FAS-

TENING DEVICES HAVE

BEEN TIGHTENED SE-

CURELY. A FREQUENT

CHECK SHOULD BE MADE

OF ALL SCREWS, BOLTS

AND FASTENING DEVICES

AND TIGHTEN IF NEEDED.

CHILD CRAFT

INDUSTRIES, INC.

P.O.BOX444

SALEM,IN47167-0444 USA

PH:812-883-3111

FAX:812-883-1819

http://www.childcraftindustries.com

MADE IN USA

H00745:11/01

▲

Inhaltsverzeichnis

Andere Child Craft Baby- und Kleinkindmöbel Handbücher

Child Craft

Child Craft Monterey F10391 Bedienungsanleitung

Child Craft

Child Craft Legacy No Drop Side Crib 37301 Bedienungsanleitung

Child Craft

Child Craft DOUBLE DROPSIDE CRIB Bedienungsanleitung

Child Craft

Child Craft Legacy Crib Bedienungsanleitung

Child Craft

Child Craft CONVERTS TO TODDLER BED AND FULL SIZE HEADBOARD AND... Bedienungsanleitung

Child Craft

Child Craft Penelope F36901 Bedienungsanleitung

Child Craft

Child Craft F02316 Bedienungsanleitung

Child Craft

Child Craft 10031 Bedienungsanleitung

Child Craft

Child Craft Delaney F31601 Bedienungsanleitung

Child Craft

Child Craft Surrey Hill F37001 Bedienungsanleitung

Child Craft

Child Craft F32401 Bedienungsanleitung

Child Craft

Child Craft Long Beach F02109 Bedienungsanleitung

Child Craft

Child Craft Crib'N'Double 31001 Bedienungsanleitung

Child Craft

Child Craft Bristol F99040 Bedienungsanleitung

Child Craft

Child Craft Westgate F38201 Bedienungsanleitung

Child Craft

Child Craft Kieran F13201 Bedienungsanleitung

Child Craft

Child Craft Jordyn F05432 Bedienungsanleitung

Child Craft

Child Craft FOREVER Eclectic Hampton F39011 Bedienungsanleitung

Child Craft

Child Craft F99106.26 Bedienungsanleitung

Child Craft

Child Craft Folding Mini Wood Crib F61301 Bedienungsanleitung

Child Craft

Child Craft DOUBLE DROPSIDE CRIB Bedienungsanleitung

Child Craft

Child Craft Elin F07116 Bedienungsanleitung

Child Craft

Child Craft Delaney F01616 Bedienungsanleitung

Child Craft

Child Craft Wadsworth 31301 Bedienungsanleitung

Beliebte Baby- und Kleinkindmöbel Handbücher anderer Marken

Mocka

Mocka Learning Tower Bedienungsanleitung

VERTBAUDET

VERTBAUDET 62003-2789 Bedienungsanleitung

Summer

Summer MY FUN POTTY Bedienungsanleitung

Grotime

Grotime Changeover Bedienungsanleitung

Fillikid

Fillikid 1221 Bedienungsanleitung

Relita

Relita loft bed ALEX Bedienungsanleitung

Joovy

Joovy Qool Bedienungsanleitung

KidKraft

KidKraft Step n Store Bedienungsanleitung

Fisher-Price

Fisher-Price L4889 Bedienungsanleitung

Germania

Germania Moon 4048.101 Bedienungsanleitung

BabyGo

BabyGo Amila Bedienungsanleitung

Fisher-Price

Fisher-Price CBV06 Bedienungsanleitung

Fisher-Price

Fisher-Price H4790 Bedienungsanleitung

Graco

Graco Dream Suite Bedienungsanleitung

Delta Childrens Products

Delta Childrens Products BB87116CR Bedienungsanleitung

Costway

Costway BB5591 Bedienungsanleitung

SAUTHON

SAUTHON UP CHENE DORE UI101A Bedienungsanleitung

Delta Children

Delta Children Classic Bedienungsanleitung