Cisco SNS-3415 series Bedienungsanleitung

CHAPTER

8-1

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Installing the Cisco SNS 3415 and Cisco SNS 3495

Hardware Appliances

This chapter describes how to install your Cisco SNS-3415 or Cisco SNS-3495 appliance and connect it

to the network.

It contains:

•Installing the Cisco SNS-3415/3495 Appliance Rack, page 8-1

•Cisco Integrated Management Controller (CIMC), page 8-5

•Configuring CIMC, page 8-5

•Connecting Cables, page 8-8

•Connecting and Powering On the Cisco SNS-3415/3495 Appliance, page 8-11

Before you begin the installation, read the Regulatory Compliance and Safety Information for the Cisco

3415 or 3495 Secure Access Control System.

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be

accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Installing the Cisco SNS-3415/3495 Appliance Rack

This section describes how to install the Cisco SNS-3415 or Cisco SNS-3495 appliance in a rack.

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special

precautions to ensure that the system remains stable. The following guidelines are provided to ensure

your safety:

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

8-2

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Chapter 8 Installing the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances

Installing the Cisco SNS-3415/3495 Appliance Rack

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the

unit in the rack.

Statement 1006

To install the slide rails and the server into a rack, follow these steps:

Step 1 Open the front securing latch (see Figure 8-1). The end of the slide-rail assembly marked “FRONT” has

a spring-loaded securing latch that must be open before you can insert the mounting pegs into the

rack-post holes.

a. On the rear side of the securing-latch assembly, hold open the clip marked “PULL.”

b. Slide the spring-loaded securing latch away from the mounting pegs.

c. Release the clip marked “PULL” to lock the securing latch in the open position.

Figure 8-1 Front Securing Latch

1 Clip marked “PULL” on rear of

assembly

3 Spring-loaded securing latch on front of

assembly

2 Front mounting pegs

332061

8-3

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Chapter 8 Installing the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances

Installing the Cisco SNS-3415/3495 Appliance Rack

Step 2 Install the slide rails onto the rack:

a. Position a slide-rail assembly inside the two left-side rack posts (see Figure 8-2).

Use the “FRONT” and “REAR” markings on the slide-rail assembly to orient the assembly correctly

with the front and rear rack posts.

b. Position the front mounting pegs so that they enter the desired front rack-post holes from the front.

Note The mounting pegs that protrude through the rack-post holes are designed to fit round or square

holes, or smaller #10-32 round holes when the mounting peg is compressed. If your rack has

#10-32 rack-post holes, align the mounting pegs with the holes and then compress the

spring-loaded pegs to expose the #10-32 inner peg.

c. Expand the length-adjustment bracket until the rear mounting pegs protrude through the desired

holes in the rear rack post.

Use your finger to hold the rear securing latch open when you insert the rear mounting pegs to their

holes. When you release the latch, it wraps around the rack post and secures the slide-rail assembly.

Figure 8-2 Attaching a Slide Rail Assembly

d. Attach the second slide-rail assembly to the opposite side of the rack. Ensure that the two slide-rail

assemblies are level and at the same height with each other.

e. Pull the inner slide rails on each assembly out toward the rack front until they hit the internal stops

and lock in place.

Step 3 Insert the server into the slide rails:

331689

256

1 Front-left rack post 4 Length-adjustment bracket

2 Front mounting pegs 5 Rear mounting pegs

3 Slide-rail assembly 6 Rear securing latch

8-4

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Chapter 8 Installing the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances

Installing the Cisco SNS-3415/3495 Appliance Rack

Note The inner rails are pre-attached to the sides of the server at the factory. You can order

replacement inner rails if these are damaged or lost (Cisco PID UCSC-RAIL1-I).

a. Align the inner rails that are pre-attached to the server sides with the front ends of the empty slide

rails.

b. Push the server into the slide rails until it stops at the internal stops.

c. Push in the plastic release clip on each inner rail (labelled PUSH), and then continue pushing the

server into the rack until its front latches engage the rack posts.

Step 4 Attach the (optional) cable management arm (CMA) to the rear of the slide rails:

Note The CMA is designed for mounting on either the right or left slide rails. These instructions

describe an installation to the rear of the right slide rails, as viewed from the rear of server.

a. Slide the plastic clip on the inner CMA arm over the flange on the mounting bracket that attached

to the side of the server. See Figure 8-3.

Note Whether you are mounting the CMA to the left or right slide rails, be sure to orient the engraved

marking, “UP” so that it is always on the upper side of the CMA. See Figure 8-3.

b. Slide the plastic clip on the outer CMA arm over the flange on the slide rail. See Figure 8-3.

c. Attach the CMA retaining bracket to the left slide rail. Slide the plastic clip on the bracket over the

flange on the end of the left slide

Figure 8-3 Attaching the Cable Management Arm (Rear of Server Shown)

331690

1 Flange on rear of outer left slide rail 5 Inner CMA arm attachment clip

2 CMA retaining bracket 6 “UP” orientation marking

8-5

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Chapter 8 Installing the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances

Cisco Integrated Management Controller (CIMC)

Step 5 Continue with the “Connecting and Powering on Cisco SNS-3415/3495 Appliance”.

Cisco Integrated Management Controller (CIMC)

You can monitor the server inventory, health, and system event logs by using the built-in Cisco Integrated

Management Controller 1.4.7a (CIMC) GUI or CLI interfaces. See the user documentation for your

firmware release at the following URL:

http://www.cisco.com/en/US/products/ps10739/products_installation_and_configuration_guides_list.html

Configuring CIMC

You can perform all operations on the Cisco SNS-3415 or Cisco SNS-3495 appliance through the CIMC.

To do this, you must first configure an IP address and IP gateway to access the CIMC from a web-based

browser.

Step 1 Plug in the power cord.

Step 2 Press the Power button to boot the server.

3 Flange on rear of right mounting

bracket

7 Outer CMA arm attachment clip

4 Flange on rear of outer right slide rail

8-6

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Chapter 8 Installing the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances

Configuring CIMC

Step 3 During bootup, press F8 when prompted to open the BIOS CIMC Configuration Utility. The following

screen appears.

Step 4 Set the NIC mode to your choice for which ports to use to access the CIMC for server management (see

Figure 6-1 for identification of the ports):

–

Dedicated—The 1-Gb Ethernet management port is used to access the CIMC. You must select

NIC redundancy None and select IP settings.

–

Shared LOM (default)—The two 1-Gb Ethernet ports are used to access the CIMC. This is the

factory default setting, along with Active-active NIC redundancy and DHCP enabled.

–

Cisco Card—The ports on an installed Cisco UCS P81E VIC are used to access the CIMC. You

must select a NIC redundancy and IP setting.

Note The Cisco Card NIC mode is currently supported only with a Cisco UCS P81E VIC

(N2XX-ACPCI01) that is installed in PCIe slot 1.

Step 5 Use this utility to change the NIC redundancy to your preference. This server has three possible NIC

redundancy settings:

–

None—The Ethernet ports operate independently and do not fail over if there is a problem.

–

Active-standby—If an active Ethernet port fails, traffic fails over to a standby port.

–

Active-active—All Ethernet ports are utilized simultaneously.

Step 6 Choose whether to enable DHCP for dynamic network settings, or to enter static network settings.

8-7

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Chapter 8 Installing the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances

Configuring CIMC

Note Before you enable DHCP, your DHCP server must be preconfigured with the range of MAC

addresses for this server. The MAC address is printed on a label on the rear of the server. This

server has a range of six MAC addresses assigned to the CIMC. The MAC address printed on

the label is the beginning of the range of six contiguous MAC addresses.

Step 7 Optional: Use this utility to make VLAN settings.

Step 8 Use this utility to set a default CIMC user password.

Note Changes to the settings take effect after approximately 45 seconds. Refresh with F5 and wait

until the new settings appear before you reboot the server in the next step.

Step 9 Press F10 to save your settings and reboot the server.

Note If you chose to enable DHCP, the dynamically assigned IP and MAC addresses are displayed on

the console screen during bootup.

Note By default, the baud rate of the serial port is set to 115200. After you configure CIMC, log in to the

CIMC user interface and change the serial port buad rate to 9600.

8-8

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Chapter 8 Installing the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances

Connecting Cables

This section describes how to connect your Cisco SNS-3415 or Cisco SNS-3495 appliance to the

network and the appliance console. This section includes:

•Connecting the Network Interface, page 8-8

•Connecting the Console, page 8-9

•Connecting the Keyboard and Video Monitor, page 8-10

•Cable Management, page 8-10

Attach cables (such as keyboard, monitor cables, if required) to the rear of the server. Route the cables

properly and use the cable straps to secure the cables to the slide rails. See Figure 6-2 “Cisco

SNS-3415/3495 Appliance Rear View” for reference on the rear view of the appliance.

Connecting the Network Interface

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

This section describes how to connect the Cisco SNS-3415 or Cisco SNS-3495 appliance Ethernet port.

The Ethernet connector supports Serial over LAN (SOL) cables. The RJ-45 port supports standard

straight-through and crossover Category 5 unshielded twisted-pair (UTP) cables. Cisco does not supply

Category 5 UTP cables; these cables are available commercially.

To connect the cable to the appliance Ethernet port:

Step 1 Verify that the appliance is turned off.

Step 2 Connect one end of the cable to the Gigabit Ethernet 0 port on the appliance.

Step 3 Connect the other end to a switch in your network.

Ethernet Port Connector

The Cisco SNS 3415 or Cisco SNS-3495 appliance comes with two integrated dual-port Ethernet

controllers. ACS 5.6 supports multiple NICs. See Multiple Network Interface Connectors, page 4-10 for

more information. These controllers provide an interface for connecting to 10-Mb/s, 100-Mb/s, or

1000-Mb/s networks and provide full-duplex (FDX) capability, which enables simultaneous

transmission and reception of data on the Ethernet LAN.

To access the Ethernet port, connect a Category 3, 4, 5, 5E, or 6 unshielded twisted-pair (UTP) cable to

the RJ-45 connector on the back of the appliance.

Table 8-1 describes the UTP cable Categories.

8-9

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Chapter 8 Installing the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances

Connecting Cables

Figure 8-4 shows the Ethernet RJ-45 port and plug.

Figure 8-4 RJ-45 Port and Plug

Table 8-2 lists and describes the RJ-45 pin signals used on the connector.

Connecting the Console

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Your Cisco SNS-3415 or Cisco SNS-3495 appliance has a DCE-mode console port for connecting a

console terminal to your appliance. The appliance uses a DB-9 serial connector for the console port.

The console port on the Cisco SNS-3415 or Cisco SNS-3495 appliance includes an EIA/TIA-232

asynchronous serial (DB-9) connector. This serial console connector (port) allows you to access the

appliance locally by connecting a terminal—either a PC running terminal-emulation software or an

ASCII terminal—to the console port.

Table 8-1 Ethernet Cabling Guidelines

Type Description

10BASE-T EIA Categories 3, 4, or 5 UTP (2 or 4 pair) up to 328 ft (100 m)

100BASE-TX EIA Category 5 UTP (2 pair) up to 328 ft (100 m)

1000BASE-T EIA Category 6 UTP (recommended), Category 5E UTP or

5 UTP (2 pair) up to 328 ft (100 m)

210222

8 7 6 5 4 32 1

RJ-45 connector

Table 8-2 Ethernet Port Pinout

Ethernet Port Pin Signal Description

1 TxD+ Transmit data +

2 TxD– Transmit data –

3 RxD+ Receive data +

4 Termination network No connection

5 Termination network No connection

6 RxD– Receive data –

7 Termination network No connection

8 Termination network No connection

8-10

Installation and Upgrade Guide for Cisco Secure Access Control System 5.6

Chapter 8 Installing the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances

Connecting Cables

To connect a PC running terminal-emulation software to the console port, use a DB-9 female to DB-9

female straight-through cable.

To connect an ASCII terminal to the console port, use a DB-9 female to DB-25 male straight-through

cable with a DB-25 female to DB-25 female gender changer.

To connect a terminal or a PC running terminal-emulation software to the console port on the Cisco

SNS-3415 or Cisco SNS-3495 appliance:

Step 1 Connect the terminal using a straight-through cable to the console port.

Step 2 Configure your terminal or terminal-emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit,

and no hardware flow control.

Connecting the Keyboard and Video Monitor

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

This section describes how to connect a keyboard and video monitor to the Cisco SNS-3415 or Cisco

SNS-3495 appliance.

You can connect the keyboard and video monitor to the Cisco SNS-3415 or Cisco SNS-3495 appliance

using the KVM connector available in the front panel of the Cisco SNS-3415 or Cisco SNS-3495

appliance. A KVM cable is shipped along with the appliance that provides two USB, one VGA, and one

serial connector.

The Cisco SNS-3415 or Cisco SNS-3495 appliance does not provide support for a mouse.

The Cisco SNS-3415 or Cisco SNS-3495 provides USB ports on the rear of the appliance that can be

used to connect a keyboard and video monitor.

To connect a keyboard and video monitor to the appliance:

Step 1 Verify that the appliance is turned off.

Step 2 Connect the end of the keyboard cable to the PS/2 (keyboard) port which is located on the back panel of

the appliance.

Step 3 Connect the end of the video monitor cable to the PS/2 (video monitor) port which is located on the back

panel of the appliance.

Step 4 Power on the appliance.

Cable Management

Cable management is the most visual aspect of your appliance setup. However, cable management is

often overlooked because it can be time consuming.

Andere Handbücher für SNS-3415 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco UCS C220 Montage- und Wartungsanleitung

Cisco

Cisco Unity Bedienungsanleitung

Cisco

Cisco UCS 6500 Series Bedienungsanleitung

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco NAC-3300 Series Bedienungsanleitung

Cisco

Cisco UCS M3 Series Bedienungsanleitung

Cisco

Cisco AS5300 - Universal Access Server Technisches Dokument

Cisco

Cisco UCS C220 M4 Kurzanleitung

Cisco

Cisco UCS C22 M3 Systemhandbuch

Cisco

Cisco Business Edition 6000S Bedienungsanleitung

Cisco

Cisco C460 M4 Bedienungsanleitung

Cisco

Cisco SCE2020-4XGBE-SM Bedienungsanleitung

Cisco

Cisco GSS-4492R-K9 Bedienungsanleitung

Cisco

Cisco UCS B460 M4 Handbuch

Cisco

Cisco IE-3000-8TC Bedienungsanleitung

Cisco

Cisco UCS C Series Bedienungsanleitung

Cisco

Cisco 7835-H2 - Media Convergence Server Bedienungsanleitung

Cisco

Cisco UCS C240 M4 Montage- und Wartungsanleitung

Cisco

Cisco Expressway CE1200 Bedienungsanleitung

Cisco

Cisco UCS B420 M3 Installations- und Betriebshandbuch

Cisco

Cisco UCS C220 M4 Montageanleitung

Cisco

Cisco UCS C220 M5 Bedienungsanleitung

Cisco

Cisco UCS C210 M2 Systemhandbuch

Cisco

Cisco UCS C260 Montage- und Wartungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung