Clarke BC125 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0714

BATTERY STARTER/CHARGER

MODEL NO: BC125, BC190

PART NO: 6210125, 6210200

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Battery starter / charger

Please read this manual thoroughly, before attempting to operate, and

carefully follow all instructions given.

It is vitally important that ALL precautions are taken, as specified, which will not

only provide protection for yourself and that of others around you, but will also

ensure that the Battery Charger will give you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

1. To prevent the battery from overheating and consequent damage, use

the BOOST facility sparingly and do not exceed our recommendations.

2. Battery acid is highly corrosive. If spillage occurs, wipe off immediately and

wash copiously with water. Particularly avoid contact with the eyes.

3. Do not expose this unit to rain.

4. Never touch the negative and positive leads together on this unit whilst it is

switched on.

5. Never attempt any electrical or mechanical repair. If you have a problem

with your machine contact your local stockist for service information.

6. Before charging ensure the battery terminals are clean, and that the cells

are filled with electrolyte to the correct level by adding distilled water

where necessary.

7. Where appropriate we recommend that the positive (+) lead to the

battery is disconnected on the vehicle prior to charging. This will prevent

damaging the vehicle electronics.

8. When charging is completed, ensure that the vehicle battery leads are

secured to the correct terminals which should be clean and lightly

smeared with petroleum jelly to prevent corrosion. Finally, re check the

electrolyte level.

WARNING: BECAUSE HIGHLY INFLAMMABLE HYDROGEN GAS IS

RELEASED IN THE PROCESS OF BATTERY CHARGING, ALWAYS REMEMBER

TO SWITCH OFF FIRST AND SO AVOID SPARKING, WHICH WILL OCCUR

WHEN CONNECTING OR DISCONNECTING LIVE LEADS.

WARNING: CERTAIN TYPES OF SEALED OR MAINTENANCE-FREE BATTERIES

NEED EXTRA CARE WHEN CHARGING. PLEASE CONSULT BATTERY

MANUFACTURERS INSTRUCTIONS BEFORE USING THIS UNIT.

WARNING: SINCE TOXIC FUMES MAY BE RELEASED DURING BATTERY

CHARGING, ONLY USE THIS UNIT IN A WELL VENTILATED AREA.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with

the markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal which is

marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal which is

marked Lor coloured Red.

• The wire which is coloured Yellow and Green must be connected to the terminal

which is marked E or or coloured Green.

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs

yourself.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

SPECIFICATIONS

BC125 BC190

Input Voltage 230V AC @ 50 Hz 230V AC @ 50 Hz

Max Rated Output Current Charging 20 Amps

Starting 120 Amps

Charging 38 Amps

Starting 180 Amps

Open Circuit Voltage

MIN 12V/24V

BOOST 12V/24V

STARTING 12V/24V

10.05 / 22.54 Volts

10.40 / 23.46 Volts

10.58 / 23.97 Volts

10.63 / 23.76 Volts

11.24 / 25.49. Volts

11.43 / 25.70 Volts

Boost Start Duty Cycle 3 Seconds ON / 120 seconds OFF -

max 5 cycles

3 Seconds ON / 120 seconds OFF -

max 5 cycles

Output Protection Fuse 2 x 50A 2 x 110A

Dimensions (D x W x H) 280 x 225 x 200 mm 280 x 225 x 200 mm

Weight (kg) 7.78.8

Part Number 6210125 6210200

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TO CHARGE THE BATTERY

NOTES ON CHARGING PROCEDURE

• A complete charge is best done slowly in order to protect your battery,

so we recommend setting the MIN/BOOST switch to the MIN position.

• A complete charge may take up to 10 hours.

• If a low amperage reading (2 amps or less) is seen on the Ammeter

gauge at either the MIN or BOOST setting, this may indicate that the

battery is either (a) already fully charged or (b) at the end of its useful

life and in need of replacement.

• Do not charge the battery for longer than is necessary.

SETUP

NOTE: Make sure that the battery cells are filled with electrolyte to the correct

level by adding distilled water.

1. Check that the ON/OFF switch on the unit is in the OFF position.

2. Connect the RED, positive lead to either the 12V or 24V terminal on the

charger, as appropriate.

3. Remove the battery filler caps, where applicable, during charging, to

prevent the build up of dangerous gases within the battery.

WARNING: NEVER ATTEMPT TO RE-CHARGE NON-RECHARGEABLE

BATTERIES.

CAUTION: When charging a car battery in situ, we recommend that

the non earthed lead on the battery is disconnected prior to charging

(On most vehicles, this would be the RED, Positive lead - but check the

vehicle handbook if you are unsure). This precaution is necessary as it is

possible that damage could occur to any electronically controlled

system fitted to the vehicle.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONNECTING TO THE BATTERY

4. Connect the RED clamp to the positive (+) terminal.

5. Connect the BLACK clamp to the chassis (or a suitable engine bolt) away

from the battery and fuel line.

6. Switch the CHARGE/START switch to the CHARGE position.

7. Set the MIN/BOOST switch to the MIN position.

• This is suitable for charging most normal car batteries.

8. Switch the ON/OFF switch to ON, and charging will commence. You can

increase the rate of charge by switching the MIN/BOOST switch to BOOST.

9. Keep the battery on charge until the Ammeter gauge reads less than 2

amps or has stopped moving down.

WHEN CHARGING IS COMPLETE

10. Switch the ON/OFF switch to OFF.

11. ALWAYS disconnect the clamps in the following order - Red then Black.

WARNING: IF THE LEADS ARE CONNECTED TO THE WRONG TERMINALS, A

FLASH WILL OCCUR WHEN THE SECOND CLAMP IS CONNECTED. THIS MAY

CAUSE THE FUSE TO BLOW, THEREBY PROTECTING THE CHARGER AND

BATTERY. IF THIS OCCURS, REMOVE THE BLACK COVER ON THE FRONT

PANEL TO ACCESS THE FUSE.AFTER REPLACING THE FUSE ENSURE THE

COVER IS REPLACED.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PROCEDURE FOR ENGINE STARTING

NOTE: Make sure that the battery cells are filled with electrolyte to the correct

level by adding distilled water.

We recommend that before attempting to boost start, you charge the battery

for 10-15 minutes. This will improve the chance of a first time start, particularly

with bigger engines. When the battery is completely flat, you must charge the

battery for 10-15 minutes before attempting to start, otherwise you may cause

damage to the vehicle electronic systems.

1. Set the ON/OFF switch to the OFF position.

2. Connect the RED, positive lead to either the 12V or 24V terminal on the

charger, as appropriate.

3. Connect the RED clamp to the positive (+) battery terminal).

4. Connect the BLACK clamp to the chassis (or a suitable engine bolt) away

from the battery and fuel line

5. Set the CHARGE/BOOST START switch to the BOOST position.

6. Switch the ON/OFF switch to the ON position.

7. Turn the ignition key to start the car.

IMPORTANT: If the engine fails to start within 3 seconds stop immediately,

and return the CHARGE/BOOST START switch to CHARGE position for a

period of 120 seconds before retrying. Failure to do this could damage

some vehicle electronic equipment, the battery, and possibly the unit

which may invalidate your guarantee.

THERMAL OVERLOAD

These starter / chargers are provided with a Thermal Overload cut-out.

Should the Duty Cycle be exceeded, or should the unit overheat for any

reason, the thermal overload will intervene, shutting down the system.

If this occurs, wait for 15 - 20 minutes, depending upon ambient temperature,

before attempting to re-use.

Once it has reset, the unit is ready for use once again.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DECLARATION OF CONFORMITY

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS DIAGRAM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Akkuladegerät Handbücher

Clarke

Clarke DIGICAR 900 Bedienungsanleitung

Clarke

Clarke Start-N-charge BC120N Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC100C Installations- und Betriebshandbuch

Clarke

Clarke IBC8 Bedienungsanleitung

Clarke

Clarke IBC7 Bedienungsanleitung

Clarke

Clarke BC 700 Handbuch

Clarke

Clarke WIBC250 Bedienungsanleitung

Clarke

Clarke CBO9-12 Bedienungsanleitung

Clarke

Clarke AC80 Bedienungsanleitung

Clarke

Clarke IBC50 Bedienungsanleitung

Clarke

Clarke ATC12V Bedienungsanleitung

Clarke

Clarke Start'N'Charge BC250 Bedienungsanleitung

Clarke

Clarke Start N charge BC100N Handbuch

Clarke

Clarke Start-N-Charge BC130 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC420N Installations- und Betriebshandbuch

Clarke

Clarke ATC12VB Bedienungsanleitung

Clarke

Clarke Start N Charge WIBC200 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC150 Bedienungsanleitung

Clarke

Clarke IBC5 Bedienungsanleitung

Clarke

Clarke IBC40 Bedienungsanleitung

Clarke

Clarke IBC4 Bedienungsanleitung

Clarke

Clarke HFBC12-24 Bedienungsanleitung

Clarke

Clarke Start'N'Charge WBC180 Bedienungsanleitung

Clarke

Clarke CB09-6/12 Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung