Clarke Start'N'Charge WBC180 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

DL0621 - ISS 3

ORIGINAL INSTRUCTIONS

BATTERY CHARGER-STARTER

MODEL NO: WBC180

PART NO: 6261500

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Battery Charger.

Please read this manual thoroughly, before attempting to operate, and

carefully follow all instructions given.

It is vitally important that ALL precautions are taken, as specified, which will not

only provide protection for yourself and that of others around you, but will also

ensure that the Battery Charger will give you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

If disposing of this product or any damaged components, do not dispose of

with general waste. This product contains valuable raw materials. Metal

products should be taken to your local civic amenity site for recycling of metal

products.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SPECIFICATIONS

Model Number WBC180

Battery Voltages 12 & 24V

Suitable Battery Types Lead Acid inc GEL, WET, AGM

IP Rating IP20

Maximum Battery Size 500 Ah

Operating Temperature Range 0 to 40°C

Dimensions (D x W x H) 274 x 370 x 590 mm

Weight 14.1 kg

Estimated Engine Capacity up to 1.6 L

Rated DC output voltage 12 & 24V

Rated DC output current 35A

Input Voltage @ 50Hz 230 V Ac

Short Circuit Protection 110A

Ammeter Range 0-60A

Starting Duty Cycle 3 sec On / 120 sec Off

Max Output Current (Starting @ 12V/24V) 220/180 A @ max duty cycle

Max Output Current (Charging @ 12V/24V) 35/35 A

Rated Input Power (Charging mode) 1.24 kW

Max Input current

Starting @ 12V/24V 12V/19A and 24V/28A

Charging @ 12V/24V 12V/3.8A and 24V/5.5A

Open Circuit Voltage (Output)

Starting @ 12V/24V 14.79 / 29.43

Boost @ 12V/24V 12.35 / 24.73

Charging 1@ 12V/24V 11.12 / 22.26

Charging 2 @ 12V/24V 11.71 / 23.46

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

PLEASE READ BEFORE USING THIS UNIT

1. Battery acid is very corrosive. If spilled, clean the area immediately and

wash with water. If battery acid comes into contact with the eyes, get

medical help immediately.

2. Do not expose this charger/starter to rain.

3. Never touch the negative and positive leads together while the unit is

switched on.

4. Never attempt any electrical or mechanical repair yourself other than

replacement of fuses. If you have a problem with your battery charger

contact your local stockist for service information.

5. Before charging, make sure that the battery terminals are clean, and the

cells are filled to the correct level by adding distilled water where

necessary.

6. This charger/starter is not intended for use by persons with reduced

physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction

concerning use of the charger/starter by a person responsible for their

safety. Keep children well away from the charger/starter.

7. After charging, secure the vehicle battery leads to the correct terminals

which should be clean, and lightly smeared with petroleum jelly to prevent

corrosion. Finally, re-check the battery electrolyte level.

8. Do not use this charger/starter unless you are aware of vehicle electrical

systems and battery charging techniques.

WARNING: HIGHLY INFLAMMABLE HYDROGEN GAS IS RELEASED IN THE

PROCESS OF BATTERY CHARGING. ALWAYS REMEMBER TO SWITCH OFF

THE CHARGER/STARTER FIRST TO AVOID SPARKING.

WARNING: CERTAIN TYPES OF SEALED OR MAINTENANCE-FREE BATTERIES

NEED EXTRA CARE WHEN CHARGING. PLEASE CONSULT THE BATTERY

MANUFACTURERS INSTRUCTIONS BEFORE USING THIS CHARGER/STARTER.

WARNING: TOXIC FUMES MAY BE RELEASED DURING BATTERY

CHARGING. ONLY USE THIS CHARGER/STARTER IN A WELL VENTILATED

AREA.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

9. Always consult the vehicle manufacturers instructions for disconnecting /

charging the vehicle battery.

CAUTION: SOME VEHICLE ELECTRONIC EQUIPMENT CAN BE DAMAGED

BY BOOST CHARGING OR USE OF THE START FACILITY. CHECK YOUR

VEHICLE HANDBOOK BEFORE USING YOUR STARTER/CHARGER. IF IN

DOUBT CONSULT THE VEHICLE MANUFACTURER.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTION

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved 13 amp BS1363 plug, or a suitably fused isolator switch,

If the plug has to be changed because it is not suitable for your socket or

because of damage, it must be removed and a replacement fitted, following

the wiring instructions shown below. The old plug must be discarded safely as

insertion into a power socket could cause an electrical hazard.

If the colours of the wires in the power cable do not agree with the markings

on the plug:

• The BLUE wire must be

connected to the terminal

which is marked “N” or coloured

black.

• The BROWN wire must be

connected to the terminal

which is marked “L” or coloured

red.

• The YELLOW AND GREEN wire

must be connected to the

terminal which is marked “E” or or coloured green.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD).

If you are not sure, consult a qualified electrician. DO NOT try to carry out any

repairs yourself.

The maximum rated supply current for this unit is 28 amps with a

duty cycle of 3 secs on/120 secs off

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE

MAINS SUPPLY.

WARNING! THIS APPLIANCE MUST BE EARTHED

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

The WBC180 model is provided with a pair of leads complete with clamps for

connection to a battery via the appropriate outlet connections - 12V and 24V,

as shown.

Three selector switches provide for different functions as shown above. The

main fuse is mounted on the front panel, as shown and both models

incorporate a thermal overload cut-out.

1 Fuse Holder 6 Power On/Off Switch

2 Charging condition meter (Amps) 7 Positive Terminal +24V

3 High/Low Charging Selector 8 Positive Terminal +12V

4 Min/Boost Charge Charging Selector 9 Negative (BLACK) lead

5 Battery Charge/Jump Start Mode

Selector switch

10 Positive (RED) lead

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

1. Pass the axle through the holes in

the body of the machine and fit

circlips to the axle at the position

shown.

2. Slide the wheels onto each end of

the axle and secure with further

circlips outside each wheel.

3. Press-fit the caps to the wheels.

4. Install the foot to the base of the

machine using the three screws as

shown.

5. Fit the positive battery lead to the

terminal of your choice (12/24V)

to match the voltage of the

battery.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL PREPARATION

CHARGER LOCATION

1. Place the charger as far away from the car battery as possible.

2. Do not position the charger above the battery during the charging

procedure. Gases from the battery will cause corrosion and damage the

charger.

3. Do not let battery acid drip on anything when reading specific gravity or

when topping up the battery.

4. Do not operate the charger in an enclosed space, such as inside the

vehicle. Never cover the battery charger.

5. Do not stand the battery on top of the charger.

6. Always stand the battery charger on a firm, level floor.

7. During charging, make sure that the area around the battery has good

ventilation.

CONNECTING THE BATTERY

1. Before charging, disconnect the battery from the vehicle.

2. Always remove the grounded (earth) terminal from the battery first. Make

sure that all electrical accessories in the vehicle are switched off to prevent

sparking.

3. Clean the battery terminals. Be careful to prevent battery electrolyte from

coming in contact with your eyes.

4. Except for sealed units, add distilled water to each cell until the battery

acid reaches the level specified by the battery manufacturer.

• This helps drive unwanted gas from the cell. Do not overfill. For a battery

without cell caps, consult the manufacturer's instructions.

5. Follow all the battery manufacturer's specified precautions: for example,

removing or not removing cell caps while being charged, and

recommended rates of charge.

6. Refer to the vehicle manual to find the voltage of the battery and make

sure that the charging cable is connected to the correct terminal (either

12/24V).

7. This charger has an adjustable charge rate and the battery should be

charged initially at the lowest rate.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONNECTING TO A BATTERY

BATTERY CHARGING

CHARGING A BATTERY INSTALLED IN THE VEHICLE

1. Position the leads carefully to reduce the risk of damage from any sharp

edges.

2. Check the polarity of the battery posts.

3. Consult the vehicle manual to confirm if the vehicle has a Negative or

Positive earth.

• For negative earth vehicles, connect the POSITIVE (RED) lead from the

battery charger to the POSITIVE terminal on the battery. Connect the

NEGATIVE (BLACK) lead to the vehicle frame or engine block away from

the battery.

• For positive earth vehicles, connect the NEGATIVE (BLACK) lead from the

battery charger to the NEGATIVE terminal on the battery. Connect the

POSITIVE (RED) lead to the vehicle frame or engine block away from the

battery.

• Do not connect the lead to ancilliary engine components.

4. Where appropriate, we recommend that the non-earthed lead on the

battery is disconnected prior to charging.

• This will reduce the risk of damage to the vehicle’s electronic

equipment.

5. When charging is completed, switch off the charger/starter and unplug it.

Remove the lead from the vehicle earth point, and then remove the lead

from the battery.

CHARGING A BATTERY REMOVED FROM THE VEHICLE

1. Make sure that you know the polarity of the battery posts.

WARNING: A SPARK NEAR THE BATTERY MAY CAUSE BATTERY EXPLOSION.

TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY:

• Turn off the charger before you connect/disconnect the DC

output connectors.

• Do not let the connectors touch each other.

• Attach the connectors to battery terminals and make sure that

you get a good connection.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Akkuladegerät Handbücher

Clarke

Clarke Start n charge BC100B Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC100C Installations- und Betriebshandbuch

Clarke

Clarke Start-N-Charge BC120C Bedienungsanleitung

Clarke

Clarke IBC50 Bedienungsanleitung

Clarke

Clarke BC 700 Handbuch

Clarke

Clarke CB09-6/12 Bedienungsanleitung

Clarke

Clarke IBC4 Bedienungsanleitung

Clarke

Clarke ZX-R Pro Series Bedienungsanleitung

Clarke

Clarke IBC8 Bedienungsanleitung

Clarke

Clarke IBC2 Bedienungsanleitung

Clarke

Clarke WBC400 Bedienungsanleitung

Clarke

Clarke LA4 Bedienungsanleitung

Clarke

Clarke WIBC250 Bedienungsanleitung

Clarke

Clarke ATC12VB Bedienungsanleitung

Clarke

Clarke DIGICAR 900 Bedienungsanleitung

Clarke

Clarke DIGICAR 600 Bedienungsanleitung

Clarke

Clarke Start N Charge WIBC200 Bedienungsanleitung

Clarke

Clarke AC80 Bedienungsanleitung

Clarke

Clarke IBC25 Bedienungsanleitung

Clarke

Clarke IBC40 Bedienungsanleitung

Clarke

Clarke JSM180 Installations- und Betriebshandbuch

Clarke

Clarke Start'N'Charge BC250 Bedienungsanleitung

Clarke

Clarke IBC80 Bedienungsanleitung

Clarke

Clarke Start-N-charge BC120N Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung