Clarke DIGICAR 900 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0715

BATTERY BOOSTER/CHARGER

MODEL NO: DIGICAR 900

PART NO: 6261205

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Battery booster / charger which is

suitable for charging and boosting 12 + 24 Volt batteries

Please read this manual thoroughly, before attempting to operate, and

carefully follow all instructions given.

It is vitally important that ALL precautions are taken, as specified, which will not

only provide protection for yourself and that of others around you, but will also

ensure that the Battery Charger will give you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

1. To prevent the battery from overheating and consequent damage, use

the BOOST facility sparingly and do not exceed our recommendations.

2. Battery acid is highly corrosive. If spillage occurs, wipe off immediately and

wash copiously with water. Particularly avoid contact with the eyes.

3. Do not expose this unit to rain.

4. Never touch the negative and positive leads together.

5. Never attempt any electrical or mechanical repair. If you have a problem

with your machine contact your local stockist for service information.

6. Before charging ensure the battery terminals are clean, and that the cells

are filled with electrolyte to the correct level by adding distilled water

where necessary.

7. Where appropriate we recommend that the positive (+) lead to the

battery is disconnected on the vehicle prior to charging. This will prevent

damaging the vehicle electronics.

8. When charging is completed, ensure that the vehicle battery leads are

secured to the correct terminals which should be clean and lightly

smeared with petroleum jelly to prevent corrosion. Finally, re check the

electrolyte level.

WARNING: BECAUSE HIGHLY FLAMMABLE HYDROGEN GAS IS RELEASED

IN THE PROCESS OF BATTERY CHARGING, ALWAYS REMEMBER TO SWITCH

OFF FIRST TO AVOID SPARKING, WHICH CAN OCCUR WHEN

CONNECTING OR DISCONNECTING LIVE LEADS.

WARNING: CERTAIN TYPES OF SEALED OR MAINTENANCE-FREE BATTERIES

NEED EXTRA CARE WHEN CHARGING. PLEASE CONSULT BATTERY

MANUFACTURERS INSTRUCTIONS BEFORE USING THIS UNIT.

WARNING: TOXIC FUMES CAN BE RELEASED DURING BATTERY

CHARGING, ONLY USE THIS UNIT IN A WELL VENTILATED AREA.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Connect the three core mains lead to a suitable industrial supply isolator, or

heavy duty plug. These chargers must be connected to a supply having a

rated capacity of greater than 13 Amps.

The maximum input current for this unit is 25amps

IMPORTANT: The wires in the mains lead are coloured in accordance with

the following code:

As the colours of the flexible cord of this appliance may not correspond with

the coloured markings identifying terminals in your plug proceed as follows:

• Connect GREEN & YELLOW coloured cord to plug terminal marked with

a letter ‘E’ or Earth symbol ‘’ or coloured GREEN or GREEN & YELLOW.

• Connect BROWN cord to terminal marked with a letter L or coloured

RED

• Connect BLUE cord to terminal marked with a letter N or coloured

BLACK

If in doubt, consult a qualified electrician.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY.

WARNING: A 13 Amp (BS1363) plug is not suitable.

WARNING: THIS APPLIANCE MUST BE EARTHED

Green & Yellow Earth

Blue Neutral

Brown Live

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

FITTING THE WHEELS

1. Use the two bolts supplied to fit

the front foot to the base as

shown.

2. Fit one of the circlips to the axle as

shown.

3. Slide the axle through the wheel

(from the outside)

4. Pass the free end of the axle

through the two holes on the

base.

5. Place the second wheel on the

end of the axle.

6. Secure with the second circlip.

FITTING THE HANDLE

1. Slide the handle into position as

shown.

2. Secure using the four screws

provided.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

NOTES ON CHARGING PROCEDURE

LOCATION

• Use the battery charger only and exclusively indoors;

• The premises must be well-ventilated;

• The premises must be dry and dust-free;

• The air vents should be free of obstructions;

• The battery charger should be placed on a stable surface.

WARNING: NEVER ATTEMPT TO RE-CHARGE NON-RECHARGEABLE

BATTERIES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CHARGING MORE THAN ONE BATTERY AT THE SAME TIME

If it is necessary to charge more than one battery at the same time, they can

be connected in series or in parallel.

• Connection in series is preferred because this makes it possible to

monitor the current circulating in each battery, this will be shown on the

display.

• Please foillow the diagram below.

WARNING: DO NOT CHARGE BATTERIES WITH DIFFERENT CAPACITIES OR

DIFFERENT TYPES OF BATTERIES AT THE SAME TIME.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

1 ON/OFF Switch

2 Green LED Lights up when the battery

charger is connected to the

mains supply

3 Yellow LED Lights up when the

Overtemperature protection

activates

4 Battery Type Selector Pb/Gel, Ca/Ca or AGM

5 Charge Process Selector Automatic or Floating

6 Charge Current / Charge time selector

7 Charge Current / Time adjustment knob

8 Charge Start / Stop button

9 Boost Start / Stop button

10 Voltage / Charge percentage display: Shows either the battery voltage

or the charge percentage.

11 Current / Timer display Shows the charge current and

the remaining charge time

12 12V / 24V Positive Cable Socket

13 Protection Fuse

14 Negative Cable

15 Positive Cable

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BATTERY CHARGING

NOTE: The charging process only activates if the battery connected has a

minimum voltage of 7.5V For 12V batteries: 18V For 24V batteries. If the

voltages are lower then this or if you want to charge a fully discarged

battery or, See “FORCED CHARGING” on page 12.

1. Connect the battery charger to the mains.

2. Switch ON the battery charger using the on/off switch.

• The green led (2) will light up.

SELECT THE BATTERY TYPE

3. Press the battery type selector (4)

to select the battery type.

• This battery charger can be

used with normal Lead

batteries (sealed or unsealed),

GEL, AGM batteries or calcium

batteries.

NOTE: If you are not sure of the

battery type, select calcium battery.

SELECT THE CHARGING PROCESS

4. Select the charging process (5):

Automatic or Floating.

AUTOMATIC

• This mode will perform a full

charge (at the set current) until

the set time has elapsed.

• The charger will then stop and

the display will show “END”.

• If you then turn the adjustment knob the display will then show the set

charge current.

• If the charging time has not been set, the charger will run for 9,9 hours

(the maximum default value).

• To stop the charge before the set time, just push the Charge start / Stop

button.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

FLOATING:

• This mode will perform a full charge (at the set current) until the set time

has elapsed.

• The charging current will decrease to a lower fixed current. A buzzer will

signal the transition from full charge to floating charge.

SELECT THE CHARGE CURRENT

5. Press the charge current/time

selector (6) until the charge

current LED lights up:

6. Turn the adjustment knob (7) to

set the desired charge current.

• The current value will be shown

in the bottom display (11).

• You should set up a value that is 10% of the battery capacity. For

example, if you have a 140Ah battery you should set up 14A.

• This battery charger allows you to set up any value of current from 1

Amp to the maximum rated amperage of the battery charger.

SELECT THE CHARGE TIME

7. Press the charge current/time

selector (6) until the charge time

LED lights up.

8. Turn the adjustment knob (7) to

set the desired charge time.

• The current value will be shown

in the bottom display (11).

9. Connect the red cable to the

required 12V/24V positive socket.

• Insert the plug on the cable

into the socket (12) on the front

of the battery charger and

then turn the plug clockwise in

order to lock it in place.

• Make sure the socket selected

is correct for the battery being

charged.

10. Connect the clamp on the red cable to the positive terminal of the

battery.

Inhaltsverzeichnis

Andere Clarke Akkuladegerät Handbücher

Clarke

Clarke IBC5 Bedienungsanleitung

Clarke

Clarke AC80 Bedienungsanleitung

Clarke

Clarke ATC12VB Bedienungsanleitung

Clarke

Clarke IBC8 Bedienungsanleitung

Clarke

Clarke Start'N'Charge BC185N Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC150 Bedienungsanleitung

Clarke

Clarke IBC4 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC260N Bedienungsanleitung

Clarke

Clarke ATC12V Bedienungsanleitung

Clarke

Clarke Start N Charge WIBC200 Bedienungsanleitung

Clarke

Clarke Start N charge BC100N Handbuch

Clarke

Clarke JSM180 Installations- und Betriebshandbuch

Clarke

Clarke Start n charge BC260N Handbuch

Clarke

Clarke IBC40 Bedienungsanleitung

Clarke

Clarke BC125 Bedienungsanleitung

Clarke

Clarke BC520P Bedienungsanleitung

Clarke

Clarke Start'N'Charge WBC180 Bedienungsanleitung

Clarke

Clarke WIBC250 Bedienungsanleitung

Clarke

Clarke IBC7 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC100C Installations- und Betriebshandbuch

Clarke

Clarke CB09-6/12 Bedienungsanleitung

Clarke

Clarke LA4 Bedienungsanleitung

Clarke

Clarke CBO9-12 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC130 Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung