Clarke JSM180 Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0721 REV 2

JUMPSTARTER & DEVICE CHARGER

MODEL NO: JSM180

PART NO: 6238900

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Power Pack & Jump Starter

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instructions in a safe place for future reference.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Lithium Ion Polymer Battery - Recycle in accordance with WEEE regulations.

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with

general household waste. It must be disposed of according to the laws

governing Waste Electrical and Electronic Equipment (WEEE) at a recognised

disposal facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONTENTS AND OVERVIEW

OVERVIEW

1 Jump Starter Power Pack 3 3 - 1 USB Charging Cable,

Lightning/Micro USB/C-Type

2 12V Battery Jump Starter Lead

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. ALWAYS ensure when jump starting that there is air circulating around the

device.

2. NEVER allow the negative and positive leads on this unit, to touch each

other or to touch the same metal object.

3. Although the jump starter is water resistant and may be used outdoors, DO

NOT leave it exposed to the elements. Avoid direct sunlight, direct heat,

rain/moisture etc.

4. The jump starter is designed for use on petrol cars up to 3L/3000cc with 12V

batteries.

5. DO NOT operate the jump starter if any of the cables are damaged.

Consult your CLARKE dealer for repair or replacement of the parts.

6. DO NOT operate the jump starter if the case is damaged. Consult your

CLARKE dealer or a qualified person for inspection and repair.

7. Ensure the vehicle battery posts and battery clamps are perfectly clean

before use.

8. When connecting the jump starter leads to a battery, ensure the device is

switched OFF, and ALWAYS connect the RED (positive’+’) output

conductor to the UNEARTHED (+) battery terminal FIRST, then connect the

BLACK, (negative’-’) conductor to a suitable earthing point on the chassis

or battery, well away from any fuel lines.

9. To prevent the battery overheating and consequent damage, DO NOT

exceed our recommendations for the duration of jump starting.

10. This jump starter is NOT designed to be used as a replacement for the

vehicle battery.

11. DO NOT attempt to BOOST CHARGE the jump starter's sealed battery.

12. NEVER attempt any repairs yourself. If you have a problem with the jump

starter contact your local CLARKE dealer.

13. NEVER jump start the engine whilst the jump starter is being charged.

14. ALWAYS store the jump starter out of reach of children.

WARNING: ALL LEAD ACID BATTERIES GENERATE HYDROGEN GAS

DURING NORMAL OPERATION. THIS PROCESS INCREASES DURING A

PERIOD OF RAPID DISCHARGE. HYDROGEN GAS AND BATTERY ACID

(SULPHURIC ACID) CAN BE EXPLOSIVE, CORROSIVE TO SKIN, EYES AND

HAIR, DAMAGING TO CLOTHING AND METALS, FLAMMABLE, POISONOUS

TO BREATHE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

POWER PACK CHARGING

1. Fully charge your jump starter battery unit before using it for the first time.

2. Recharge the jump starter battery unit after every occasion of use if

possible, and thereafter, at least every 6 months.

3. ALWAYS AVOID leaving your jump starter unit in a discharged state.

FOLLOW THE ABOVE POINTS TO ENSURE MAXIMUM LIFE FROM THE BATTERY.

BATTERY CAPACITY INDICATOR LIGHTS

Pressing the power switch, the indicator lights will show as follows:

During the charging of the power pack, the power indicator lights will flash

and turn on one by one. When all four lights remain on, it means the unit is fully

charged.

During the discharging of the unit, if the first indicator light is flashing, it means

the unit is short of power and needs recharging.

There are three means of charging the power pack:

1. Via a 230V USB mains adaptor (not supplied), using the USB charging cable

2. Via a PC’s USB terminal, using the USB charging cable.

3. Via a 12V auxiliary vehicle adapter (not supplied), with the USB charging

cable.

CHARGING USING A 230V USB MAINS ADAPTOR OR PC TERMINAL

1. Plug the C-TYpe end of the charging

cable into the C-type port on the Jump

Starter power pack.

2. Plug the USB plug end of the charging

cable into a USB mains adaptor (not

supplied) or a PC’s USB terminal and

switch on.

Indicator Light 1 Light On 2 Lights On 3 Lights On 4 Lights On

Capacity 25% 50% 75% 100%

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• The BLUE charging/indicator lights on

the jump starter will come on and start

flashing to indicate charging is in

progress.

3. Continue to charge until all 4 BLUE

charging lights stop flashing and stay on.

It is important to note that this could take up to 4 hours, dependant upon

the state of charge of the battery.

CHARGING USING A 12V AUXILIARY ADAPTOR

1. Plug the C-type end of the charging

cable into the C-Type port on the Jump

Starter power pack.

2. Plug the USB end of the charging cable

into a USB 12V auxiliary adaptor (not

supplied) and insert the 12V adaptor into

your car 12V auxiliary port.

• The BLUE charging/indicator lights on

the jump starter will come on and start

flashing to indicate charging is in

progress.

3. Continue to charge until all 4 BLUE

charging lights stop flashing and stay on.

It is important to note that this could take

up to 4 hours, dependant upon the state

of charge of the battery.

MAINTENANCE

Always ensure the cables & clamps are in good condition and the clamps are

clean and corrosion free. If damaged they should be replaced. Keep the unit

clean by wiping with a dry cloth. DO NOT use solvents as a cleaning agent.

NEVER attempt any repair unless your are a qualified technician. Your CLARKE

jump starter has been designed to give long and trouble free service. If,

however, having followed the instructions in this booklet carefully, you

encounter problems, take the unit to your local CLARKE dealer.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

LED LIGHT

The power pack has an LED light that has 3 settings and can be used as a

torch or safety lighting as follows.

1. Press and hold the power switch for 3 seconds to turn on the torch setting.

2. Press the power switch again to turn on the LED flashing strobe effect

lighting.

3. Press the power switch for a third time to turn on the LED SOS flashing effect

lighting.

4. Press the power switch for a fourth time to turn the LED light off.

CHARGING MOBILE PRODUCTS

1. Choose the appropriate mobile charging adaptor on the charging cable,

Lightning, Micro USB or USB-C type, and connect to the device to be

charged.

2. Insert the USB end of the charging lead into the USB output charging port

on the power pack.

3. Press the power switch for charging to begin.

NOTE: The blue indicator lights will keep bright when charging. If the

device doesn’t start charging after 3 seconds the indicator lights

and device will turn off.

JUMP STARTING A 12V CAR (PETROL ONLY)

ALWAYS carry out the following preliminary checks before connecting the

jump starter to the car battery:

• Ensure the vehicle ignition and ALL ancillary equipment - lighting,

radio etc, are switched off.

WARNING: FAILURE TO FOLLOW THE INSTRUCTIONS BELOW AND THE

SAFETY INSTRUCTIONS ON PAGE 6 MAY RESULT IN PERSONAL INJURY,

DAMAGE TO THE VEHICLE, OR THE POSSIBILITY OF AN EXPLOSION

WARNING: IT IS POSSIBLE THAT SOME ELECTRONIC EQUIPMENT COULD BE

DAMAGED BY JUMP STARTING. ALWAYS CHECK WITH THE CAR

MANUFACTURER’S HANDBOOK TO DETERMINE WHAT PRECAUTIONS IF

ANY SHOULD BE TAKEN.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Ensure the vehicle battery is rated at 12V and is not damaged in any

way. If the battery is damaged, replace battery, DO NOT try and

recharge.

• Ensure the battery terminals are clean and the clamps are firm and

secure.

• Ensure the area is well ventilated.

• Take great care not to touch the red positive (+) clamp against the

black negative (-) clamp.

1. Make sure two or more power indicator

lights are showing on the jump starter.

2. Connect the red positive (+) clamp to

the positive (+) battery terminal first. Take

care the clamp does not contact any

moving parts or fuel lines.

3. Connect the black negative (-) clamp

to the negative (-) battery terminal or to

a suitable earthing point on the vehicle

chassis ensuring the connections are firm

and secure.

4. Insert the blue plug end of the battery

jump starter lead into the 12v car jump

port on the battery unit, making sure the

lead is firmly and correctly inserted,

otherwise it may affect the starting

function.

5. Switch the car ignition to start for no

more than 6 seconds. If car doesn’t start,

switch off and wait 3 minutes before

trying again.

6. If the car fails to start on the first attempt, make sure all lead connections

are correctly positioned. If, after 3 attempts to jump-start the car have

failed, STOP, as this may damage the car and/or its electrical systems.

7. Once the car has started, remove the jump starter lead from the power

pack, before removing the clamps from the battery.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SPECIFICATIONS

SYMBOLS DISPLAYED

Item Specification

Model No. JSM180

Max Engine Capacity Under 3.0L (Petrol Only)

Battery Type Lithium Ion Polymer (Li-Po)

Battery Capacity 1800 mAh

Input (C-type cable) 5V/1A

Output for Mobile Devices (USB) 5V/1A

Output for Car Jump 12V

Start Current Start/Peak 180A/360A

Cycles after Full Charge 5-10

Lifetime > 1000 Cycles

Charging Time 4 Hours

Discharge Operating Temperature -20°C - 60°C

IP Rating IPX0

Light 5V, 1.5W, Single LED

Size (L x W x D) 140mm x 80mm x 20mm

Weight 260g

Read the manual and

safety instructions before use

Electrical hazard due to exposed live terminals

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DECLARATION OF CONFORMITY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Akkuladegerät Handbücher

Clarke

Clarke Start N Charge WIBC200 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC420N Installations- und Betriebshandbuch

Clarke

Clarke IBC2 Bedienungsanleitung

Clarke

Clarke AC80 Bedienungsanleitung

Clarke

Clarke ATC12VB Bedienungsanleitung

Clarke

Clarke IBC80 Bedienungsanleitung

Clarke

Clarke Start-N-charge BC120N Bedienungsanleitung

Clarke

Clarke DIGICAR 600 Bedienungsanleitung

Clarke

Clarke Start n charge BC260N Handbuch

Clarke

Clarke Start'N'Charge WBC180 Bedienungsanleitung

Clarke

Clarke LA4 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC120C Bedienungsanleitung

Clarke

Clarke CBO9-12 Bedienungsanleitung

Clarke

Clarke WBC400 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC100C Installations- und Betriebshandbuch

Clarke

Clarke Start n charge BC100B Bedienungsanleitung

Clarke

Clarke Start'N'Charge BC185N Bedienungsanleitung

Clarke

Clarke Start'N'Charge BC250 Bedienungsanleitung

Clarke

Clarke IBC7 Bedienungsanleitung

Clarke

Clarke HFBC12-24 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC130 Bedienungsanleitung

Clarke

Clarke DIGICAR 900 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC120C Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC150 Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung