Clarke LA4 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

LS1214

LEAD ACID BATTERY CHARGER

MODEL NO: LA4 & LA6

INTRODUCTION

Thank you for purchasing this CLARKE Battery Charger.

Please read this manual thoroughly, before attempting

to operate, and carefully follow all instructions given.

It is vitally important that ALL precautions are taken, as

specified, which will not only provide protection for

yourself and that of others around you, but will also

ensure that the Battery Charger will give you long and

satisfactory service.

This Battery Charger is limited to use with 12V Lead Acid

Batteries ONLY.

DO NOT attempt to charge other types of battery

GUARANTEE

This CLARKE product is guaranteed against faulty

manufacture for a period of 12 months from the date of

purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have

been abused or tampered with in any way, or not used

for the purpose for which it was intended.

Faulty goods should be returned to their place of

purchase, no product can be returned to us without

prior permission.

This guarantee does not effect your statutory rights

SAFETY PRECAUTIONS

• IMPORTANT: ALWAYS disconnect the battery from the

vehicle BEFORE connecting the charger leads. This is

to prevent damage being caused to the vehicles

electronic systems.

• This battery charger is designed for INDOOR use ONLY.

Do not use outdoors, exposed to the elements.

• This battery charger is for charging I2V Lead-Acid

type batteries only. Do not use for any other type of

battery, or supply power to low voltage electrical

systems.

• Do not attempt to charge a battery with a capacity

exceeding that indicated in the ‘Specifications’.

• Do not operate the charger if any of the cables are

damaged. Consult your Clarke dealer for repair or

replacement of the parts.

• Do not operate the charger if the case is damaged.

Consult your Clarke dealer for inspection and repair.

• Do not disassemble the charger, incorrect reassembly

may result in electric shock or fire.

• Ensure the battery posts and battery clamps are

perfectly clean before use.

• Connect the battery clamps to the battery terminals

before plugging the charger in to the mains power

supply.

• Disconnect from the mains power supply before

making or breaking connections to the battery.

• Make sure the battery is topped up with distilled

water, (where applicable), to its proper level, before

connecting the charger.

• Unscrew the battery filler caps fully, (where

applicable), and leave them loose for the duration of

charge, to ensure that gases are allowed to escape.

NOTE: ALWAYS clean around the filler caps

thoroughly before unscrewing, to ensure

that no dirt can enter the battery cell.

Ensure the breather holes, in the caps, are

perfectly clear before screwing in again.

• When charging is complete, disconnect the negative

cable first and then the positive cable.

• Always place the charger in an environment which is

- well ventilated

- out of the reach of children

- not exposed to direct sunlight or heat source

- not exposed to rain or other adverse conditions

- away from water / moisture, oil and grease

- away from explosive gases, flames, and sparks

- away from any flammable substance

ELECTRICAL CONNECTIONS

THIS APPLIANCE IS DOUBLE INSULATED

This appliance is fitted with a 13 amp, BS 1363 plug which

should be connected to a standard 230 VAC (50Hz)

electrical supply. If the plug is replaced, the

replacement must be to the same specification and

wired in accordance with the following code:

Blue - Neutral

Brown - Live

As the colours of the flexible cord of this appliance may

not correspond with the coloured markings identifying

terminals in your plug proceed as follows:

• Connect BROWN cord to terminal marked with a

letter “L” or coloured RED

• Connect BLUE cord to terminal marked with a letter

“N” or coloured BLACK

If in doubt, consult a qualified electrician.

In the event a moulded plug is fitted, and is subsequently

cut from the electric cable, the replacement plug MUST

be an approved 13 amp, BS 1363 plug and wired in

accordance with the above instructions. Additionally,

please note:

1. The discarded plug must be thrown away as

there is a danger of electric shock if it is

subsequently inserted into a socket outlet.

2. Never use the plug without the fuse cover fitted.

3. Should you wish to replace a detachable fuse

carrier, ensure that the correct replacement is

used (as indicated by marking or colour code).

4. Replacement fuse covers can be obtained from

your local dealer or most electrical stockists.

FUSE REPLACEMENT

The fuse in the plug must be replaced with one of the

same rating (5 amps) and this replacement must be

ASTA or BSI approved to BS1362.

EXTENSION CABLES

If an extension cable is used, the conductors in the

cable MUST be a minimum 1.5mm

. Additionally, ensure

the cable is completely unwound from the drum.

USING THE CHARGER

Ensure the battery to be charged is rated at 12V and

that it is not damaged or in an overly discharged state,

otherwise it may draw too much current from the

charger and damage may result.

DISCONNECT THE BATTERY FROM THE VEHICLE

If the battery is still in the vehicle, ensure the battery

terminals are disconnected from the vehicles electrical

system. Disconnect the negative (EARTH) terminal first,

followed by the positive terminal. (When reconnecting,

do so in reverse order).

CONNECT THE CHARGER TO THE BATTERY

1. Connect the red battery clamp to the positive

(+ve) battery terminal.

2. Connect the black clamp to the negative (-ve)

terminal,

• Make sure that both connections are secure and NOT

touching each other.

CHARGE THE BATTERY

3. Plug in the charger and switch ON at the mains

supply.

4. Set the ON/OFF switch to ON to commence

charging.

WHEN CHARGING IS COMPLETE

5. When charging is complete (charger display

needle goes fully to the left), set the ON/OFF

switch to OFF.

• Damage to the battery could occur should the

charger be left connected for a prolonged period.

6. Disconnect the charger from the battery.

• Remove the black clamp from the

negative (-ve)

terminal first.

• Then remove the red clamp from the positive (+ve)

terminal.

7. Reconnect the battery to the vehicle.

SAFETY FEATURES

Whenever a fault condition exists, the circuitry

automatically disengages the normal operation of the

charger.

THERMAL OVERLOAD

The thermal overload protector provides a safeguard

against an excessively large charging current being

drawn by the battery for prolonged periods.

SHORT CIRCUIT

The charger is fully protected against short circuits, i.e.

the clamps coming into contact with each other

(directly or indirectly) when the unit is switched ON.

If a short circuit does occur, the fuse on the bottom of

the unit may ‘blow’ and need replacing before using

the charger again. The fuse required is a 7.5A blade fuse.

REVERSE POLARITY

The charger is fully protected against the possibility of

the clamps being incorrectly connected.

SPECIFICATIONS

Model LA4 LA6

Input Voltage 230V @ ~50Hz

Battery Voltage: 12 V

IP Rating: IP20

Minimum battery

size: (Ah/CCA)

10Ah 12Ah

Maximum battery

size: (Ah/CCA)

60Ah

Operating

Temperature

Range: (°C)

-10 to 45°C

Compatible

battery types:

Lead acid only

Dimensions

(D x W x H)

95 x 172 x 177 mm 97 x 170 x 177 mm

Weight (kg) 1.35 1.7

Part Number 6266300 6266305

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Akkuladegerät Handbücher

Clarke

Clarke IBC80 Bedienungsanleitung

Clarke

Clarke IBC2 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC150 Bedienungsanleitung

Clarke

Clarke ZX-R Pro Series Bedienungsanleitung

Clarke

Clarke IBC8 Bedienungsanleitung

Clarke

Clarke DIGICAR 900 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC260N Bedienungsanleitung

Clarke

Clarke CBO3-12 Bedienungsanleitung

Clarke

Clarke Start n charge BC260N Handbuch

Clarke

Clarke CB09-6/12 Bedienungsanleitung

Clarke

Clarke IBC50 Bedienungsanleitung

Clarke

Clarke ATC12VB Bedienungsanleitung

Clarke

Clarke AC80 Bedienungsanleitung

Clarke

Clarke IBC5 Bedienungsanleitung

Clarke

Clarke IBC7 Bedienungsanleitung

Clarke

Clarke Start-N-Charge BC420N Installations- und Betriebshandbuch

Clarke

Clarke IBC4 Bedienungsanleitung

Clarke

Clarke DIGICAR 600 Bedienungsanleitung

Clarke

Clarke Start N charge BC100N Handbuch

Clarke

Clarke Start-N-Charge BC120C Bedienungsanleitung

Clarke

Clarke IBC40 Bedienungsanleitung

Clarke

Clarke Start N Charge WIBC200 Bedienungsanleitung

Clarke

Clarke JSM180 Installations- und Betriebshandbuch

Clarke

Clarke ATC12V Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung