Clarke CBG8W Installations- und Betriebshandbuch

8” WETSTONE

BENCH GRINDER

8” WETSTONE

BENCH GRINDER

OPERATING & MAINTENANCE

INSTRUCTIONS 0805

Thank you for purchasing this Clarke Bench Grinder. Before attempting to operate

this bench grinder please read this instruction manual thoroughly and follow all

directions carefully. This is for your own safety and that of others around you, and

to help you achieve long and trouble free service from your bench grinder.

GUARANTEE

This product is guaranteed against faults in manufacture for 12 months from

purchase date. Keep your receipt as proof of purchase.

This guarantee is Invalid if the product has been abused or tampered with in any

way, or not used for the purpose for which it is intended.

The reason for return must be clearly stated.

This guarantee does not affect your statutory rights.

FOR YOUR OWN SAFETY

WARNING! Read these instructions before using the equipment.

• Always wear suitable Clarke safety goggles, manufactured to the latest

European Safety Standards, when Grinding or polishing.

• Do not use the grinder if the guard visor is not in place, or if it is damaged.

• Check that there Is nothing flammable in the working area, as sparks from

the grinder can easily start a fire.

• Disconnect the grinder from the mains supply before changing the grinding

wheel, or topping up the water in the wetstone water bath.

• Never grind on the side face of the wheel. This can cause stresses in the

wheel and lead to the wheel bursting.

• Do not use the grinder if the grinding wheel is damaged or out of balance.

• Keep loose clothing, long hair etc. clear of the grinder. Do not hold the

workpiece with a rag or similar as these can be caught up in the grinder.

Note: Bench grinders used in industrial environments may be subject to the

requirements of The Provision and Use of Work Equipment regulations 1992

(particularly regarding the training requirement of The Abrasive Wheels Regulations

1970), or other legislation. If in doubt seek advice.

TECHNICAL DATA

Model : ................................................ CBG8W

Part No: ................................................ 6500112

Electric motor: .................................... 275 Watts, 240 Volt, Single phase,

Class ‘E’,

Cycle: .................................................. 10mins ON 10mins OFF

Dry wheel (mm): ................................ 150 x20 x12.7 Bore

Wetstone wheel (mm): ...................... 200x40 x20 Bore

WARNING! THIS MACHINE MUST BE EARTHED

This product is provided with a standard 13 amp, 230 volt (50Hz). BS 1363 plug, for

connection to a standard, domestic electrical supply. Should the plug need

changing at any time, ensure that a plug of identical specification is used.

IMPORTANT: The wires in the mains lead should be wired up in accordance with

the following colour code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the wires in the mains lead may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

• Connect the GREEN & YELLOW cord to terminal marked with a letter “E” or

Earth symbol “ ”

• Connect BROWN cord to plug terminal marked letter “L”

• Connect BLUE cord to plug terminal marked letter “N”

We recommend that this machine is connected to the mains supply through a

Residual Current Device (RCD).

FUSE RATING

The fuse in the plug for this appliance must be rated at 13 amps

EXTENSION CABLES

If an extension cable is used, always ensure it is fully unwound. When used outdoors,

ensure the extension cable is specifically designed for outdoor use.

Ensure that the cable is rated for the voltage and amperage of the machine.

IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

Do not carry out any electrical repair yourself.

ELECTRICAL CONNECTIONS

ASSEMBLY AND INSTALLATION

1. Fix the grinder to the bench using suitable screws or bolts through the holes In

the grinder base. Do not overtighten the securing screws.

The grinder has rubber mounting feet to help minimise vibration, and these

will not be effective if compressed too tightly. If using bolts, make sure they will

not work loose under vibration by fitting locknuts or similar.

2. Fit the guard visor as shown in the illustration. Position the visor mounting bracket

to within 1.5mm (1/16") of the wheel.

3. Fit the work rest as shown in the illustration, positioning it to within 1.5mm (11/6")

of the wheel. This will help to prevent the workpiece being dragged between

the wheel and the work rest.

.4. Rotate the wheel by hand to make sure the visor mounting bracket and work

rest are clear of the wheel.

5. Any fault which might lead to fracture in a new grinding wheel is likely to show

in its first minute of operation. Switch the grinder on, stand clear, and allow the

grinder to run for a minute or so before using it for the first time.

MAINTENANCE AND REPLACING WHEELS

WARNING Disconnect the grinder from the mains supply before fitting replacement

wheels, cleaning or adjustment.

Keep the machine clean by wiping off dust with a clean cloth, and occasionally

blowing the grinder through with air. Always wear protective goggles when blowing

through with compressed air.

The grinding wheel may need trueing or dressing occasionally. Only dress the

wheel with a proper dressing tool, whilst wearing safety goggles or glasses. If in

doubt seek advice.

Use only correct replacement wheels, of a suitable grade for your intended use.

Check that the spindle speed (no-load speed) marked on the machine does not

exceed the maximum rpm marked on the grinding wheel. Consult your dealer if

in doubt about choosing the correct replacement wheel.

Check replacement wheels thoroughly for any signs of damage before fitting.

Replacement wheels must fit easily, but not loosely, on to the machine spindle.

Do not attempt to fit a wheel that is tight on the spindle. There is a danger of a

tight fitting wheel bursting in use if the spindle expands due to becoming hot.

To replace the grinding wheel: Remove the wheel guard and guard visor (three

nuts and bolts). Unscrew the wheel retaining nut (normal right hand thread), and

remove the flange, blotter, and used wheel. Reassemble as shown in the diagram.

To replace the wetstone wheel: Drain the water bath by removing the plug in the

bottom. Remove the water bath (three screws). Unscrew the wheel retaining nut

(normal right hand thread), flange, and used wheel. Reassemble as shown in the

diagram.

Do not overtighten the wheel retaining nut when reassembling - hand pressure

with a standard spanner is sufficient. There is a danger of damaging the wheel if

the nut Is overtightened.

Switch the grinder on, stand clear, and allow the grinder to run for a minute or so

before using a new wheel for the first time.

Grinding Wheel Wetstone Wheel

PARTS DIAGRAM

1. Screw HT8481901

2. Washer HT8481902

3. Cover HT8481903

4. Water Trough HT8481904

5, Rubber Cork HT8481905

6. Pin HT8481906

7. Worm Wheel HT8481907

8. Worm HT8481908

9. Both HT8481909

10. Short Axis HT8481910

11. Journal Bearing HT8481911

12. Worm Gear Case HT8481912

13. Big Washer HT8481913

14. Wheel Flange HT8481914

15. Wet Wheel HT8481915

16. Nut HT8481916

17. Left Main Body HT8481917

18. Cable Protector HT8481918

19. Capacitor HT8481919

20. Connecting HT8481920

21. Base HT8481921

22. Rubber Foot HT8481922

23. Switch HT8481923

24. Switch Cover HT8481924

25. Seal Plate HT8481925

26. Earth Connection HT8481926

27. Cable Adaptor HT8481927

28. Rotor HT8481928

29. Cable Washer HT8481929

30. Cable Nut HT8481930

31. Cable HT8481931

32. Middle Main Body HT8481932

33. Stator HT8481933

34. Right Main Body HT8481934

35. Inner Cover HT8481935

36. Knob Nut HT8481936

37. Tool Rest HT8481937

38. Square Neck Screw HT8481938

39. Wheel Flange HT8481939

40. Dry Wheel HT8481940

41. Outer Cover HT8481941

42. Bolt HT8481942

43. Eyeshield HT8481943

44. Eyeshield Bracket HT8481944

45. Spring Washer HT8481945

PARTS LIST

Item Description Part No.

Andere Handbücher für CBG8W

Inhaltsverzeichnis

Andere Clarke Schleifer Handbücher

Clarke

Clarke CBG8W Installations- und Betriebshandbuch

Clarke

Clarke Metalworker CBG8370L Bedienungsanleitung

Clarke

Clarke X-Pro CAT206 Installations- und Betriebshandbuch

Clarke

Clarke CON2600 Bedienungsanleitung

Clarke

Clarke CAG115C Installations- und Betriebshandbuch

Clarke

Clarke CAT130 Installations- und Betriebshandbuch

Clarke

Clarke Metalworker CAG122 Installations- und Betriebshandbuch

Clarke

Clarke Contractor CON1050 Installations- und Betriebshandbuch

Clarke

Clarke air CAT143 Installations- und Betriebshandbuch

Clarke

Clarke METALWORKER CBG6RZ Installations- und Betriebshandbuch

Clarke

Clarke Metalworker CBG8370LW Bedienungsanleitung

Clarke

Clarke Metalworker CBG6250LW Bedienungsanleitung

Clarke

Clarke CAT36B Installations- und Betriebshandbuch

Clarke

Clarke CAG232 Installations- und Betriebshandbuch

Clarke

Clarke CON1150 Bedienungsanleitung

Clarke

Clarke METALWORKER CHDBG900 Bedienungsanleitung

Clarke

Clarke Air CAT112 Installations- und Betriebshandbuch

Clarke

Clarke air CAT129 Installations- und Betriebshandbuch

Clarke

Clarke METALWORKER CAG121 Installations- und Betriebshandbuch

Clarke

Clarke CAT65 Installations- und Betriebshandbuch

Clarke

Clarke CAT83 Installations- und Betriebshandbuch

Clarke

Clarke CBG6RL Handbuch

Clarke

Clarke CAG800 Installations- und Betriebshandbuch

Clarke

Clarke CONTRACTOR CON1050B Installations- und Betriebshandbuch

Beliebte Schleifer Handbücher anderer Marken

Parkside

Parkside PWS 230 C3 Bedienungsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Technisches Handbuch

PTA

PTA P1322 Bedienungsanleitung

Crown

Crown CT13313 Bedienungsanleitung

Parkside

Parkside 280250 Bedienungsanleitung

Climax

Climax VM2150 Series Bedienungsanleitung

Jet

Jet JPSG-618M1 Service-Handbuch

Makita

Makita GA4030 Bedienungsanleitung

DeWalt

DeWalt DWEN202 Bedienungsanleitung

Grizzly

Grizzly G2790 Bedienungsanleitung

Fein

Fein MSf843-1a Bedienungsanleitung

Bosch

Bosch GWS 14,4 V PROFESSIONAL Bedienungsanleitung

RAMSET

RAMSET CBAGR18 Bedienungsanleitung

Bosch

Bosch 8-115 Z Bedienungsanleitung

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Bedienungsanleitung

MW TOOLS

MW TOOLS ME15W Bedienungsanleitung

Caravaggi

Caravaggi SP 20 Betriebsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Technisches Handbuch