Clarke CAT36B Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS

GC0315

STRAIGHT DIE GRINDER

MODEL NO: CAT36B, CAT89 & CAT98

PART NO: 3110436, 3110845 & 3110854

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Air Tool.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the tool.

USE OF POWER TOOLS

1. Stay alert and use common sense - do not operate this tool when you are

tired or under the influence of alcohol, drugs or medication.

2. Always wear eye protectors when using air tools. Eye protectors must

provide protection from flying particles from the front and the side.

3. Always wear ear protectors and a dust mask when using the air tool.

4. Do not overreach - Keep proper footing and balance at all times.

5. Never use oxygen, CO2, combustible gasses, or any bottled gas, as a

source of power for this tool. This product should only be used with a

suitably rated compressed air supply.

6. Do not connect the air supply hose with your finger on the trigger.

7. Do not fit the tool to any stand or clamping device that may damage it.

8. Do not exceed the maximum pressure for the tool of 90 psi / 6.2 bar.

9. Keep the air supply hose away from heat, oil and sharp edges.

10. Check hoses for leaks or excessive wear before use, and ensure that all

connections are secure.

11. Do not use the tool for any other purpose than described in this manual.

12. Do not carry out any alterations or modifications to the tool.

13. Always disconnect from the air supply when:

• Performing any maintenance.

• The tool is not in use.

• The tool will be left unattended.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Moving to another work area.

• Passing the tool to another person.

14. Never use the tool if it is defective or operating abnormally.

15. This tool should be serviced at regular intervals by qualified service

personnel.

16. Avoid damaging the tool for example by applying excessive force.

17. Always maintain the tool with care. Keep it clean for the best and safest

performance.

18. Quick change couplings should not be located at the tool. They add

weight and could fail due to vibration.

19. Do not force or misuse the tool. It will do a better and safer job at the rate

for which it was designed.

20. Do not remove any labels. Damaged labels should be replaced.

21. This tool vibrates with use. Vibration may be harmful to your hands or arms.

Stop using the tool if discomfort, a tingling feeling or pain occurs. Seek

medical advice before resuming use.

USE OF THE GRINDING TOOLS

1. Ensure that sparks and particles resulting from use do not create a hazard,

Use screens where appropriate.

2. Never bump the grinding stones onto the workpiece, or let it hit any other

objects while grinding.

3. Always allow the tool to run up to full operating speed before applying it to

the job.

4. Use clamps, or vices to hold the workpiece. Failure to secure the workpiece

could result in personal injury.

TRANSPORTATION & STORAGE

1. Never carry an air tool by the air supply hose.

2. Never carry an air tool with your finger on the trigger.

3. When not in use, the tool must be disconnected from the air supply and

stored in a dry place out of the reach of children (preferably in a locked

cabinet).

4. Avoid storing in cold environments.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

The CAT89 Die Grinderis identical to the CAT98 other than in the body style.

The CAT36B Die Grinder KIt includes a CAT89 Die Grinder together with the

accessories shown.

When opening the case for the first time, check against the following list that

all the items are present. Any damage or deficiency should be reported to

your CLARKE dealer immediatey.

NO DESCRIPTION NO DESCRIPTION

1 Moulded Storage Case (CAT36) 4 Male Snap Connector

2 CAT89 Die Grinder 5 10 Grinding Stones (CAT36B only)

3 2 x Collet Wrenches 6 2 x Collets (1 already fitted to tool)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

• A build-up of moisture or oil in the air compressor will accelerate

wear and corrosion in the tool. ensure any moisture is drained from

the compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required, (over 8 metres), the line

pressure or the hose inside diameter may need to be increased.

• The air hose must be rated at least 150% of the maximum operating

pressure of the tool.

• A typical air line layout is shown above. If an automatic in-line filter/

regulator is used, it will keep the tool in good condition, but should

be regularly checked & topped up with oil. Clarke air-line oil should

be used, and the lubricator adjusted to approx 2 drops per minute.

• Never exceed the maximum operating pressure for the tool. It is

recommended that air pressure to this tool does not exceed 90 psi

at the tool when running. Higher pressures and unclean air will

shorten the life of the tool due to faster wear and is a possible safety

hazard.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

NOTE: Ensure the compressor is turned off.

1. If required, connect an in-line mini oiler to the tool.

• A mini oiler helps to prolong the life of the air tool.

2. If a mini-oiler is not being used, run a few drops of oil through the tool

before use. It can be entered through the inlet connector or via the hose

at the nearest connection to the air supply.

3. Connect a suitable hose as shown.

4. Connect the other end of the hose

to the compressor.

5. Turn on the air supply and check

for air leaks. Rectify any found

before proceeding.

• PTFE tape may be helpful for

sealing threaded connections.

6. Your air tool is now ready for use.

You can fit a whip hose with a quick fit coupling if required (available from

your Clarke dealer).

INSTALLING THE COLLET

1. Select the grinding stone you require.

2. Three collets of different sizes are

provided. Select whichever fits

the shank of the stone you have

chosen.

• The larger collet is probably

already installed in the grinder.

3. If a different collet is to be used,

undo the screw cap completely

and pull out the collet from the

collet seat. Replace it with the

new collet and screw the cap loosely back on.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR

COMPRESSORS AND COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

FITTING THE GRINDING STONE

IMPORTANT: Never use chipped or cracked grindstones.

1. Slip the shank of the chosen stone

into the collet and tighten the

screw cap finger tight.

2. Place one wrench over the collet

seat to stop the tool from rotating.

3. Use the other wrench to fully

tighten the collet and grip the

stone in position as shown.

OPERATING THE DIE GRINDER

1. Use your thumb to slide the

throttle locking lever forward while

squeezing the trigger against the

body of the tool.

2. Do not use excess pressure on the

grinding stone as this will shorten

its life.

3. Release the trigger to stop the

grinder.

• The tool will continue to rotate

very briefly after the trigger has been released.

Always ensure the grinder has stopped before putting it down.

SETTING THE SPEED

1. Adjust the tool speed by setting

the air regulator on top of the tool

body using a suitable screwdriver.

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the air supply hose until the compressor has been shut

down and the compressed air released.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. Refer to the compressor instruction manual for the procedure to shut down

and release the compressed air.

3. Once the pressure has been released, disconnect the air supply hose from

the tool.

STORAGE

If the tool is to be stored, or is idle for longer than 24 hours, run a few drops of

Clarke air line oil into the air inlet, and run the tool for 5 seconds in order to

lubricate the internal parts.

When not in use, disconnect from air supply, clean tool and store in a safe, dry

place. When storing, ensure the blanking plug is replaced on the airline

connector once the airline is disconnected.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TROUBLESHOOTING

SYMPTOM PROBLEM SOLUTION

Tool runs at normal

speed but slows down

under any load.

1. Motor parts worn.

2. Worn or sticking

mechanism due to

lack of lubricant.

1. Return to Clarke dealer

for repair.

2. Drip air tool lubricating

oil into air inlet. Allow oil

to soak moving parts

before using.

Tool runs slowly. Air flows

weakly from exhaust.

1. Motor parts jammed

with gum/dirt.

2. Air-line regulator in

closed position.

3. General airflow

blocked by dirt.

1. Examine inlet air filter for

blockage. Drip a few

drops of air tool lubricat-

ing oil into air inlet.

2. Adjust in-line regulator to

open position.

3. Operate tool in short

bursts.

Tool will not run. Air flows

freely from exhaust.

1. Motor vanes stuck

due to buildup of

foreign material.

1. Disconnect air supply

and rotate tool assembly

manually.

2. Try operating tool in

short bursts.

3. Tap motor housing gently

with a rubber mallet.

4. Drip a few drops of air

tool lubricating oil into air

inlet to soak moving

parts.

Tool will not shut off. 1. Throttle O-rings

damaged or ill-fitting

in seat.

1. Return to Clarke dealer

for repair.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Schleifer Handbücher

Clarke

Clarke CBG6RP Installations- und Betriebshandbuch

Clarke

Clarke CAG232 Installations- und Betriebshandbuch

Clarke

Clarke CBG8W Installations- und Betriebshandbuch

Clarke

Clarke METALWORKER CHDBG900 Bedienungsanleitung

Clarke

Clarke METALWORKER CBG6SB Installations- und Betriebshandbuch

Clarke

Clarke METALWORKER CBG6RZ Installations- und Betriebshandbuch

Clarke

Clarke Metalworker CBG8370LW Bedienungsanleitung

Clarke

Clarke CON1150 Bedienungsanleitung

Clarke

Clarke Metalworker CBG6250LW Bedienungsanleitung

Clarke

Clarke METALWORKER CAG121 Installations- und Betriebshandbuch

Clarke

Clarke CAT65 Installations- und Betriebshandbuch

Clarke

Clarke CAG115C Installations- und Betriebshandbuch

Clarke

Clarke Metalworker CBG6250L Bedienungsanleitung

Clarke

Clarke CON2600 Bedienungsanleitung

Clarke

Clarke CAG2350 Bedienungsanleitung

Clarke

Clarke Metalworker CAG122 Installations- und Betriebshandbuch

Clarke

Clarke CAT143 Installations- und Betriebshandbuch

Clarke

Clarke X-Pro CAT206 Installations- und Betriebshandbuch

Clarke

Clarke Contractor CON1050 Installations- und Betriebshandbuch

Clarke

Clarke CBG8W Installations- und Betriebshandbuch

Clarke

Clarke CAT 89 Fehlerbehebungshandbuch

Clarke

Clarke CAT146 Installations- und Betriebshandbuch

Clarke

Clarke air CAT143 Installations- und Betriebshandbuch

Clarke

Clarke METALWORKER CHDBG500 Bedienungsanleitung

Beliebte Schleifer Handbücher anderer Marken

Parkside

Parkside PWS 230 C3 Bedienungsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Technisches Handbuch

PTA

PTA P1322 Bedienungsanleitung

Crown

Crown CT13313 Bedienungsanleitung

Parkside

Parkside 280250 Bedienungsanleitung

Climax

Climax VM2150 Series Bedienungsanleitung

Jet

Jet JPSG-618M1 Service-Handbuch

Makita

Makita GA4030 Bedienungsanleitung

DeWalt

DeWalt DWEN202 Bedienungsanleitung

Grizzly

Grizzly G2790 Bedienungsanleitung

Fein

Fein MSf843-1a Bedienungsanleitung

Bosch

Bosch GWS 14,4 V PROFESSIONAL Bedienungsanleitung

RAMSET

RAMSET CBAGR18 Bedienungsanleitung

Bosch

Bosch 8-115 Z Bedienungsanleitung

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Bedienungsanleitung

MW TOOLS

MW TOOLS ME15W Bedienungsanleitung

Caravaggi

Caravaggi SP 20 Betriebsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Technisches Handbuch