Clarke Air CAT147 Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS

GC1215

MINI AIR BLOWGUN

MODEL NO: CAT147

PART NO: 3120161

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Air Blow Gun.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

SPECIFICATION

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Model Number CAT147

Max Operating Pressure 90 psi (6.2 bar)

Approx Air Consumption 9.5 cfm (max @90psi)

Air Inlet Size 1/4“BSP Female

Weight 150 g

Dimensions (L x W x H) 108 x 23 x 29 mm

Compressed air supply 1.5 hp compressor and above

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

• A build-up of moisture or oil in the air compressor will accelerate

wear and corrosion in the tool. Ensure any moisture is drained from

the compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required, (over 8 metres), the line

pressure or the hose inside diameter may need to be increased.

• The air hose must be rated at least 150% of the maximum operating

pressure of the tool.

• A typical air line layout is shown above. If an automatic in-line filter/

regulator is used, it will keep the tool in good condition, but should

be regularly checked and topped up with oil. clarke airline oil should

be used, and the lubricator adjusted to approx 2 drops per minute.

• For optimum performance it is recommended that a 3/8” ID hose is

used.

Never exceed the maximum operating pressure for the tool. It is

recommended that air pressure to this tool does not exceed 90 psi at the tool

when running. Higher pressures and dirty air will shorten the life of the tool due

to faster wear and is a possible safety hazard.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the tool.

4. Do not operate the tool where there are flammable liquids or gases.

USE OF AIR POWERED TOOLS

1. Stay alert and use common sense - do not operate the tool when you are

tired or under the influence of alcohol, drugs or medication.

2. Always wear eye protectors when using the air tool. Eye protectors must

provide protection from flying particles from the front and the side.

3. Do not overreach - Keep proper footing and balance at all times.

4. Never use oxygen, CO2, combustible gasses or any type of bottled gas as

a source of power for this tool.

5. Do not connect the air supply hose with your finger on the trigger.

6. Do not exceed the maximum pressure for the air tool of 90 psi / 6.2 bar.

7. Keep the air supply hose away from heat, oil and sharp edges.

8. Do not fit the air tool to any stand or clamping device that may damage it.

9. Check hoses for leaks or worn condition before use and ensure that all

connections are secure.

10. Do not use the air tool for any purpose than that described in this manual.

11. Do not carry out any alterations or modifications to the air tool.

12. Always disconnect from the air supply when performing any maintenance.

13. Never use the air tool if it is defective or operating abnormally.

14. Always maintain the air tool with care. Keep it clean for the best and safest

performance.

15. Never discharge this blow gun at any persons or animals.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TRANSPORT & STORAGE

1. Never carry the blow gun by the air hose or with your finger on the trigger.

2. When not in use the blow gun should be disconnected from the air supply

and stored in a dry place out of the reach of children.

3. Avoid storing the tool where the temperature is below 0oC.

Please keep these instructions in a safe place for future reference.

BEFORE USE

1. Ensure the compressor is turned

off.

2. Connect a suitable airline hose as

shown to the air inlet connector of

the mini blow gun.

3. Connect the other end of the hose

to the compressor.

4. Turn on the air supply and check

for air leaks. Rectify any found

before proceeding.

• PTFE tape may be useful for sealing threaded connections.

5. Your mini blow gun is now ready for use.

• You can fit a whip hose with a quick fit coupling if required, available

from your Clarke dealer.

Set the compressed air pressure to suit at the compressed airline regulator.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

1. Before use, drain water from the airline filter and compressor.

2. Clean thoroughly after use with a suitable solvent.

PERFORMANCE

Please note that factors other than the tool may effect its operation and

efficiency such as reduced compressor output, excessive drain on the airline,

moisture or restrictions in the air-line, or the use of connectors of improper size

or poor condition which will reduce air supply.

Your Clarke air tool has been designed to give long and trouble free service. If,

however, having followed the instructions in this booklet carefully, you

encounter problems, take the unit to your local Clarke dealer.

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the air supply hose until the compressor has been shut

down and the compressed air released.

2. Refer to the compressor instruction manual for the procedure to shut down

and vent the compressed air.

3. Once the pressure has been released, disconnect the air supply hose from

the air tool.

ACCESSORIES

A wide range of accessories is available including filter/regulators, lubricators,

high-pressure hoses (5 to 50 metres) etc.

Contact your Clarke dealer for further information or the Clarke International

Service Department.

WARNING: MAKE SURE THAT THE BLOW GUN IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE

PROCEDURES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS

No Description No Description

1 Main Housing 9 Nozzle

2 Spring 10 Nozzle Sleeve

3 O-ring 11 Venturi Tip

4 Valve Stem 12 Ring (1)

5 O-ring 13 Ring (2)

6 O-ring 14 Ring (3)

7 Valve Seat 15 O-ring

8 Button 16 Air Inlet Connector

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Elektrowerkzeuge Handbücher

Clarke

Clarke CTC150LI Bedienungsanleitung

Clarke

Clarke DHC-2 Bedienungsanleitung

Clarke

Clarke CMPS2 Bedienungsanleitung

Clarke

Clarke FP18 Bedienungsanleitung

Clarke

Clarke Air CSG3KC Installations- und Betriebshandbuch

Clarke

Clarke CAT209 Installations- und Betriebshandbuch

Clarke

Clarke Contractor CON15 Installations- und Betriebshandbuch

Clarke

Clarke CPSB1 Bedienungsanleitung

Clarke

Clarke Woodworker CPT600 Installations- und Betriebshandbuch

Clarke

Clarke STRONG-ARM CSA12F Bedienungsanleitung

Clarke

Clarke CBM 2B Installations- und Betriebshandbuch

Clarke

Clarke CPT1000 Bedienungsanleitung

Clarke

Clarke CAT108 Installations- und Betriebshandbuch

Clarke

Clarke PRO235 Installations- und Betriebshandbuch

Clarke

Clarke CHT 459 Bedienungsanleitung

Clarke

Clarke CAT211 Installations- und Betriebshandbuch

Clarke

Clarke MetalWorker CDP151B Installations- und Betriebshandbuch

Clarke

Clarke PSW1 Bedienungsanleitung

Clarke

Clarke METALWAORKER CDP502F Bedienungsanleitung

Clarke

Clarke CDP10B Installations- und Betriebshandbuch

Clarke

Clarke CE7 PRO Bedienungsanleitung

Clarke

Clarke X-Pro CAT213 Installations- und Betriebshandbuch

Clarke

Clarke CHG1600 Bedienungsanleitung

Clarke

Clarke Strong-Arm AHP 26 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung