Classic Exhibits LTG-1001 Bedienungsanleitung

www.classicexhibits.com

Step 1

Page 1 of 4

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - LTG-1001 - Assembly

Setup Instructions:

A) Use standoff screws to secure the front panel and

back panel of the pedestal to the side panels.

B) After assembling front, back, and side panels,

slide shelf into place. The shelf will sit on pins on the

inside of the side panels.

C) Set counter top on top of assembled pedestal base.

Standoff

Screw

Front Panel

Shelf sits on

shelf pins.

Attach the oval counter

top to the pedestal base.

www.classicexhibits.com

Step 2

Page 2 of 4

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - General Information

The Tool Typical Connection Horizontal Inline Connection (remove only one setscrew) Base Plate Connection Vertical Connection

(remove only two setscrews)

Most exhibits can be assembled

with the supplied Hex Key Tool.

Occasionally, a flat head screw-

driver may be required.

Most horizontal extrusion connections have a patented expandable lock.

This lock inserts into the groove of an opposing extrusion. Tightening the

lock with the Hex Key Tool expands the lock and creates a strong positive

connection.

Remove only (1) setscrew when disassembling.

Replace setscrew in extrusion after assembling it.

Before packing, replace setscrew in extrusion to

avoid losing it.

Attach base plate to round or

square vertical extrusion using

the bolt provided. Be careful not

to strip the threads.

When vertical extrusions are

packed in portable cases rather

than crates or tubs, they must be

broken down into smaller sections

which then require assembly.

Remove only (2) setscrews when

disassembling. Replace setscrews

in extrusion after assembling it.

Before packing, replace setscrews

in extrusion to avoid losing them.

Using Your Setup Instructions

The Euro LT Hybrids Setup Instructions are created specifically for your configuration.

They are laid out sequentially in levels, including exploded views, and a logical series of detailed steps

to assemble the main structure and components. We encourage you to study the instructions before

attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling your exhibit to prevent loss of the

locks and setscrews (see below in RED). This is VERY IMPORTANT.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) When cleaning laminate inserts, countertops, or panels use mild cleansers and a soft material such as

cotton.

3) Keep all display components away from extreme heat and long exposure to sunlight to avoid warping

and fading.

4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of

shipping damage.

Typical Connection (cont’d) Numbered Label

Each extrusion contains a numbered

label which corresponds with setup

instructions. The label is located within

a groove of the extrusion (when

possible). With extrusion components

the labels contain Black numbers unless

otherwise specified.

Detail C EliateDDliateDDetail B

Detail A

Setscrews

Cut Away View Of

Slide Clips

Left Hand

Grasps Panel

Firmly

With Right Hand Thumb

Close to Seam

Squeeze,

Push Forward,

And Lift

Color Coded Clip

w/ assembly number

Panel Lock

When Required

Black Clip

is bottom of

panel

Connector Top View of Panels with LocksExample of Connection

Color Coded Clip

w/ assembly number

is top of panel

Panel Lock

When Required

Each component has 2 clips,

the lower clip is ALWAYS

black. The top clip is color

coded to distinguish which

level. The color coded clip

also contains the numbered

label.

Components connect together

by aligning them and sliding

downward connecting clips

together.

Configurations are assembled

from left to right, usually starting

with #1 and following the

numbered sequence.

The first level of components contain panel

locks that are located at the top of the

panel for extra stability and seamless con-

nection. When disassembling panels twist

top connection slightly and lift right panel

upward.

General Setup Instructions for Extrusion System

Level 1 = Blue

Level 2 = Red

Level 3 = Green

Level 4 = Black

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits RE-2015 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary Magellan Miracle VK-2094 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1549 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1232 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1019 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1556C Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2005 Handbuch

Classic Exhibits

Classic Exhibits Magellan Designs VK-1063 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1181 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1624 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-2008 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1144 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2037 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-2101 Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GK-1014 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-411 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408 Handbuch

Classic Exhibits

Classic Exhibits Magellan Designs VK-1091 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS 38907 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1340 Handbuch

Classic Exhibits

Classic Exhibits Perfect 10 Helio Bedienungsanleitung

Classic Exhibits

Classic Exhibits LTE-1001 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1121 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-2108 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung