Classic Exhibits Visionary DESIGNS 38907 Handbuch

www.classicexhibits.com

Step 1

Page 1 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 -

General Layout

20’

10’

Plan View

www.classicexhibits.com

Step 2

Page 2 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 - General Information

The Tool Typical Connection

Horizontal Inline Connection (remove only one setscrew)

Base Plate Connection Vertical Connection

(remove only two setscrews)

Most Visionary Designs exhibits can be

assembled with the supplied Hex Key Tool.

Occasionally, a flat head screwdriver may

be required.

Most horizontal extrusion connections have a patented expandable lock. This lock inserts into

the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock

and creates a strong positive connection.

Remove only (1) setscrew when disassembling. Replace setscrew in

extrusion after assembling it. Before packing, replace setscrew in

extrusion to avoid losing it.

Attach base plate to round or square

vertical extrusion using the bolt provided.

Be careful not to strip the threads.

When vertical extrusions are packed in

portable cases rather than crates or

tubs, they must broken down into

smaller sections which then require

assembly.

Remove only (2) setscrews when

disassembling. Replace setscrews in

extrusion after assembling it. Before

packing, replace setscrews in extrusion

to avoid losing them.

Using Your Setup Instructions

The Visionary Designs Setup Instructions are created specifically for your

configuration. They are laid out sequentially, including an exploded view of

the entire display, and then a logical series of detailed steps to assemble the

main structure and components. We encourage you to study the instructions

before attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling your

exhibit to prevent loss of the locks and setscrews (see below in RED).

This is VERY IMPORTANT.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only

non-abrasive cleaners.

2) When cleaning laminate inserts or countertops, use mild cleansers and a

soft material such as cotton.

3) Keep all display components away from extreme heat and long exposure

to sunlight to avoid warping and fading.

4) Retain all packing material. It will make re-packing much easier and will

reduce the likelihood of shipping damage.

Typical Connection (cont’d)

Numbered Label

Each extrusion contains a numbered label which

corresponds with setup instructions.

The label is located within a groove of the extrusion

(when possible). With Visionary Designs the labels

contain Black numbers unless otherwise specified.

Detail C EliateDDliateDDetail B

Detail A

Setscrews

www.classicexhibits.com

Step 1

Page 1 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 - Backwall Assembly

Steps:

1) Attach lower

verticals [2,3,4,5] to base plates [1].

2) Attach upper verticals [2a,3a,4a,5a] to lower verticals [2,3,4,5].

3) Connect horizontals [6a,6b] and [7a,7b] together.

4) Attach horizontals [6a/6b,7a/7b] between verticals [2/2a,3/3a]

and [4/4a,5/5a] as shown.

5) Attach horizontals [8a & 9a] to verticals [3 & 3a] and

horizontals [8b & 9b] to vertical [4 & 4a] as shown.

7) Apply graphics to Velcro on back of assembled backwall.

Item Qty Description

1 4 Base Plate

2/2a 1/1 42” RR91 Vertical Extrusion

3/3a 1/1 42” RR91 Vertical Extrusion

4/4a 1/1 42” RR91 Vertical Extrusion

5/5a 1/1 42” RR91 Vertical Extrusion

6a/6b 2/2 26” Z45 Horizontal Extrusion

7a/7b 2/2 76” Z45 Horizontal Extrusion

8a/8b 1/1 39” Z45 Horizontal Extrusion

9a/9b 1/1 22.39” Z45 Horizontal Extrusion

Attach graphics

to velcro on back of

assembled backwall

Attach graphics

to velcro on back of

assembled backwall

Velcro:

Back/Top Edge

Velcro:

Back/Top Edge

Velcro:

Back/Top Edge

Velcro:

Back/Bottom Edge Velcro:

Back/Bottom Edge

Velcro:

Back/Bottom Edge Velcro:

Back/Bottom Edge

6a 6b

7a 7b

6a 6b

7a 7b

www.classicexhibits.com

Step 2

Page 2 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 -

Steps:

1) Connect curved extrusions together as shown.

2) Attach verticals [10a,10b] to bottom of extrusion [11] as shown.

3) Attach verticals [10a,10b] to horizontals [8a,8b] as shown.

4) Connect horizontal [9a] to curved extrusion [13]

and horizontal [9b] to curved extrusion [15] as shown.

5) Attach graphics to backside of assembled frame.

Item Qty Description

10a/10b1/1 5.06” Z45 Vertical Extrusion

11 1 47.56” Z45 Curved Extrusion

12 1 47.56” Z45 Curved Extrusion

13 1 47.56” Z45 Curved Extrusion

14 1 47.56” Z45 Curved Extrusion

15 1 47.56” Z45 Curved Extrusion

16 1 47.56” Z45 Curved Extrusion

Attach graphics

to velcro on back of

assembled backwall

10a 10b

Backwall Circle Assembly

www.classicexhibits.com

Step 3

Page 3 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 -

Connections are made by holding the button

down and sliding the red tube into opposing

tube until the connection is made. To disassemble

push button and pull or twist extrusions apart.

Push-Button

Numbered Label

Using Your Setup Instructions

The Aero Canopy Setup Instructions are created specically for your conguration. They include an

exploded view of the frame which is sequentially numbered. We encourage you to study the instructions

before attempting to assemble your exhibit.

Connections are kept very simple: no tools. Everything assembles with push-button

connectors and pre-connected horizontal sections.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood

of shipping damage.

Canopy Assembly

Steps:

1) Connect canopy pieces together as shown.

2) Apply pillow case graphic to assembled canopy

Push-Button

Push button then rotate

for packing purposes

www.classicexhibits.com

Step 4

Page 4 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 - Backwall Attachments

Steps:

1) Connect iPad clamshells to backwall

where indicated, as shown in detail.

Hex

Nuts

Swivel

Mounting Plate

Swivel iPad

Clamshell

Attachment

Slide connectors into groove

of extrusion. Tighten setscrew

to secure in place. Attach

monitor mount to connectors

with screws.

Bolt iPad clamshell to mounting

plate with hex nuts.

Connectors

iPad Mount

Wire

Access

iPad

Lock

www.classicexhibits.com

Step 5

Page 5 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 -

Steps:

1) Connect horizontals [19] to verticals [17,18] inserting infills as shown.

2) Connect horizontals [19] to extrusions on backside of front panel.

3) Connect horizontals [20] between verticals [17,18] as shown.

4) Hang door on hinges as shown in detail.

5) Attach shelf supports to Velcro on inside of assembled base.

6) Place internal shelf on shelf supports.

7) Place counter top on top of assembled base.

Item Qty Description

17 1 38” S40 Vertical Extrusion w/ Door Hinge

18 1 38” S40 Vertical Extrusion w/Door Stop

19 4 18” Z45 Horizontal Extrusion

20 2 20” Z45 Horizontal Extrusion

Shelf

Support

Door

Counter Top

Shelf

Front Panel

stays assembled

Door

Hinge

Door Attachment

Slide pin into

hinge attached

to vertical.

Slide door

hinge atop pin.

Pedestal Assembly

www.classicexhibits.com

Step 6

Page 6 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 - iPad Kiosk Assembly

Lock

Infill

When assembled

Attach connector piece to tray

as shown. Then connect

assembled pamphlet

tray to vertical extrusion.

Adjustable Pamphlet Tray Attachment

Tighten Lock

to Secure

Wire

Access

iPad

Lock

Foam Lining

Removed

Home Button Shield

Optional Cover for Home Button

1) Remove foam lining from inside bottom of

clam shell as shown.

2) Attach Home Button Shield with double-sided

tape to inside of clam shell, keeping top of

shield flush with clam shell opening as shown.

NOTE: This is a permanent fix and can’t be easily

removed.

Steps:

1) Slide infill between stand verticals as shown.

2) Attach horizontal [2] between stand verticals.

3) Attach base [1] to stand verticals using bolts.

4) Attach square plate [3] to stand using bolt.

5) Attach clam shell [4] to square plate [3] using hex nuts.

6) Insert iPad and feed wire through hole.

7) Attach pamphlet trays to stand. Refer to detail.

Clam Shell

Stand

Base

Plate

Square

Plate

Hex

Nuts

Tools Required:

1) Hex Tool

2) Pliers

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 - Case Packing - Case 1 of 5

3a 3 2 2a

Base Plate

(2)

Base Plate

(2)

Setup Hardware

Lights

Top View of Each Level

Level 1 Level 2

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #38907 - Case Packing - Case 2 of 5

8b 8a 5a 5 4a 4

6a,6a,

7a,7a

6b,6b,

7b,7b

10a,

10b

Connectors (3)

Connector

Graphics

Top View of Each Level

Level 1 Level 2

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-2959 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1232 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1137 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1960 Supernova Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1950 Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GK-2008 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary VK-2098 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1214 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2009 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1556C Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1246 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1247 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1109 Handbuch

Classic Exhibits

Classic Exhibits LTK-1139 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1022 Handbuch

Classic Exhibits

Classic Exhibits Perfect 10 Helio Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary designs MOD-1529 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1340 Handbuch

Classic Exhibits

Classic Exhibits Magellan Designs VK-1063 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-1030 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1722 Handbuch

Classic Exhibits

Classic Exhibits Curved Counter Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-4022 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1180 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung

Classic Exhibits visionary DESIGNS 38907 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken