Classic Exhibits SYMPHONY SYK-1032 Handbuch

Order #XXXXX

Locked layer contains

placeholder marks.

Perspective View

Plan View

10’

SYK-1032 - 10’ x 10’ Portable Display

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

REV 7/2022

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq ft

Plan View

Order #XXXXX

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, keep all

knobs & connectors attached to

extrusions during disassembly.

Part Identification - Numbering

Engaged Lock

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

WARNING

General Information

Order #XXXXX

TSP49 Profile

All knobs must be tightened securely to ensure a proper connection.

Adjust connectors if necessary to

prevent gaps in connection.

Upper Horizontal Extrusion

Lower Horizontal Extrusion

Corner

Connector Corner

Connector

Corner

Connector

Corner

Connector

COMPLETED ASSEMBLY

Slide verticals over

lower connectors.

Then slide upper

connectors into

groove of verticals.

Tighten all knobs.

Corner Connection

3) Tighten all knobs to secure connection.

Disassembly

1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of

corner connectors on lower and upper

horizontal extrusions.

1) Loosen knobs, then slide vertical extrusions onto

corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal

extrusion into grooves of vertical extrusions.

Disassembly

1) Loosen all knobs.

2) Slide connectors off of one extrusion.

3) Tighten knobs to prevent loss during

packing & shipping.

Keep straight connectors in groove of

extrusion. Do not remove connectors

during disassembly.

Straight Connection

3) Tighten all knobs to secure connection.

When assembling frame, first attach all straight

connectors, then attach corner connectors.

1) Place extrusions end-to-end.

Slide connector across seam of extrusions.

Tighten all knobs.

All knobs must be tightened securely to ensure a proper connection.

Straight Connector

2) Loosen all knobs, then slide straight

connector across the seam of extrusions.

Tool-less Frame Assembly

Case 1 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

Top View of Each Level

Level 2 Level 3 Level 4 Level 5Level 1

(Bottom level)

Level 6

13 13

5,7

2,4 8,10

11,11

12,12

Counter

Legs

Lights

Monitor

Mount

Setup

Hardware

Counter

Top

Graphics

Header

Graphic

Workstation

Graphic

Case Packing

Case 2 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

Top View of Each Level

Level 1

(Bottom level)

Level 2 Level 3

Counter Top

Front Panel DoorPanel

Floor

Shelf

Left &

Right

Side

Panels

Level 4 Level 5

Shelf

Supports

Standoffs

& Key

Case Packing

Step 1 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

When assembled

Item

Qty.

Steps:

Refer to the Tool-less Frame Assembly general information page.

1) Assemble vertical extrusions [1-2], [3-4], [11-12] & horizontals [5-6-7], [8-9-10]

together, using Tool-less Spline Connectors labeled [X].

2) Connect vertical assemblies [1/2], [3/4] between horizontal

assemblies [5/6/7], [8/9/10], using Tool-less Corner Connectors labeled [A] & [C].

3) Install Base Plates [13] to bottom corners of frame assembly

as shown. See Base Plate Attachment detail.

4) Lift frame to upright position, then connect vertical assemblies [11/12] between

horizontal assemblies [5/6/7], [8/9/10] using Connection Lock w/ Knob.

Description

45”h TSP49 Vertical Extrusion

30.091”h TSP49 Vertical Extrusion

45”h TSP49 Vertical Extrusion

30.091”h TSP49 Vertical Extrusion

36.467”w TSP49 Horizontal Extrusion

38”w TSP49 Horizontal Extrusion

20.211”w TSP49 angled Horizontal Extrusion

38”w TSP49 Horizontal Extrusion

45.8”h Z45 Vertical Extrusion

41.209”h Z45 Vertical Extrusion w/ mitered top

6” x 22” Base Plate w/ flange

Connection Lock

w/ Knob

BACK VIEW

Knobs face back of assembly.

Tool-less Spline Connector

1. Place extrusions end-to-end.

2. Slide tool-less connectors

across seam of extrusions.

3. Tighten all knobs to secure connection.

Tool-less Corner Connector

1. Slide extrusion onto

Corner Connector.

2. Tighten all knobs to

secure connection.

Keep corner connectors attached to horizontal extrusions.

Assemble frame flat on ground.

1) Place key hole over bolt on panel

& slide down.

2) Twist knob to secure connection.

Base Plate Attachment

bolt

knob

Base Plate

threaded

hole

key hole

FRONT VIEW

Note: Extrusions [9A-9B]

stay attached.

Peak corner

connector

Peak corner

connector

*X*

Backwall Frame Assembly

Step 2 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Steps:

1) Apply SEG Graphic to front of assembled frame.

SEG Graphic Installation

Corner A

Corner D

Corner B

Corner C

It is important to first insert

graphic into each alternate

corner, then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Graphic Removal

To remove the graphic from

the frame, locate the fabric

pull tab. Gently pull up on

the tab to remove the fabric.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

When assembled

FRONT VIEW

Grap

Fabric Graphics Application

Step 3 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Workstation

Light

Steps:

1) Attach Workstation Mounting Bracket

to backwall vertical as shown.

See Workstation Bracket Attachment detail.

2) Assemble Workstation legs & counter top to

bracket. See Workstation Assembly detail.

3) Affix Graphic to front of workstation assembly,

using Velcro.

4) Attach Lights to top of backwall as shown.

See Light Attachment detail.

Attach clamp of stem light

to top of horizontal extrusion

where desired.

Twist knob on back to

tighten in place.

Light Attachment

knob

Light

BACK VIEW

Extrusion

Hook the Mounting Bracket

over the vertical extrusion.

Slide

Bracket

forward

Slide down onto

V4 connector

Tighten knobs

to secure.

Mounting

Bracket

Workstation Bracket Attachment

Slide bracket forward, then

down onto V4 connector.

Tighten thumb screws to

secure connection to inside

of frame.

Bracket

TOP VIEW SIDE VIEW

123

V4 connectors stay permanently

attached to vertical extrusion.

Threaded

Studs

Wing

nuts

Counter Top

Mounting

Bracket

Counter

Legs

UNDERSIDE VIEW

3) Attach power cords to

wireless chargers.

2) Connect Counter Top to

Mounting Bracket, using

wing nuts.

1) Attach threaded studs on underside

of Counter Top to Counter Legs;

secure with wing nuts.

Workstation Assembly

Keep cords attached to

underside of counter top.

Underside View of Counter

To Power

USB

charging

pad

power

cords

charging

block

Counter Top

When assembled

Graphic

Backwall Attachments

Step 4 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

When Assembled

Floating Graphic Attachment

Hook the Graphic Bracket

onto the extrusion & snap

into place.

Affix graphic to Bracket

using Velcro.

Brackets may be attached to

horizontal or vertical extrusion.

Two (2) brackets are required per graphic.

Graphic Bracket

Velcro

TOP VIEW

Extrusion

Hook Bracket

over

vertical

Snap into

place

Velcro

Bracket

Velcro

Graphic

Floating

Graphic

Steps:

1) Connect Floating Graphic to backwall using

brackets. See Floating Graphic Attachment

detail.

Backwall Attachments (cont’d)

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits LTG-1001 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2009 Handbuch

Classic Exhibits

Classic Exhibits Visionary Designs MOD-1243 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1247 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-2959 Handbuch

Classic Exhibits

Classic Exhibits eco systems ECO-2041 Handbuch

Classic Exhibits

Classic Exhibits visionary designs VK-1359 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1019 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids VK-1049 Handbuch

Classic Exhibits

Classic Exhibits Perfect 10 Helio Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1119 Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GK-1014 Bedienungsanleitung

Classic Exhibits

Classic Exhibits LTK-1139 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1201 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1121 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1519 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1109 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1010 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1226 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary MOD-1294 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1108 Bedienungsanleitung

Classic Exhibits

Classic Exhibits vilonary DESIGN MOD-1430 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1624 Handbuch

Classic Exhibits

Classic Exhibits visionary designs VK-2084 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung