CommScope SYSTIMAX 360 760150144 Bedienungsanleitung

SYSTIMAX®Solutions www.commscope.com

Instruction Sheet 860509975

Issue 2, December 2012

SYSTIMAX 360™FTP Evolve Panel Instructions

General

The SYSTIMAX 360™ Evolve modular foiled twisted pair (FTP) patch panel is a highly flexible 24- or 48-port,

front or rear accessible patch panel assembly. The panel is available in a straight or angled version. When

properly grounded and installed with HGS620 outlets, modular patch cords, and cables, it is an integral part of an

FTP connectivity system. The panel mounts in a standard 19-inch (483 mm) equipment rack with universal hole

spacing and incorporates lugs for panel grounding.

Ordering information is listed below:

Material ID Description

760150144 FTP Evolve 24-port flat panel

760151498 FTP Evolve 48-port flat panel

760151290 FTP Evolve 24-port angled panel

760151746 FTP Evolve 48-port angled panel

The FTP Evolve panel is available iPatch®ready. For instructions on using the panel in an iPatch application,

see 860513491 iPatch®Ready Upgrade Module for SYSTIMAX 360 Panels.

SYSTIMAX 360™FTP Evolve 48-Port Flat Panel and 48-Port Angled Panel

How to Contact Us

•To find out more about CommScope® products, visit us on the web at http://www.commscope.com/

•For technical assistance:

- Within the United States, contact your local account representative or technical support at

1-800-344-0223. Outside the United States, contact your local account representative or

Authorized Business Partner.

- Within the United States, report any missing/damaged parts or any other issues to

CommScope Customer Claims at 1-866-539-2795. Outside the United States, contact your

local account representative or Authorized Business Partner.

860509975

Instruction Sheet www.commscope.com

Page 2 of 5

Tools Required

•Phillips head screwdriver

•Cable jacket scoring tool

•D-914 punch tool with M110 blade

Parts List

Verify parts against parts list below:

Quantity

Description24-Port Flat

Panel 48-Port Flat

Panel 24-Port Angled

Panel 48-Port Angled

Panel

1 ―――24-port flat panel

―1 ――48-port flat panel

――1 ―24-port angled panel

―――1 48-port angled panel

1 1 ――Front cover (1U or 2U)

――1 1 Center cover (1U or 2U) angled panel

――2 2 Side covers for angled panel (1U or 2U)

right or left

4 4 4 4 P12-24 x ½” mounting screws

1 2 1 2 Adhesive label (5 per strip)

Cable management bar

4 8 4 8 Cable management troughs

4 8 4 8 Hook-and-loop straps

2 4 2 4 Hex nut with lock washer

1 1 1 1 Instruction sheet

Step 1 – Mount Panel to Rack

Side cover

Angled panel

Center cover

12-24 screws

(4 places)

Rack

Flat panel

Cover 12-24 screws

(4 places)

1. Mount panel to rack using the four 12-24 mounting screws provided. After securing panel to rack, snap the

Evolve cover(s) onto the front of the panel.

Note: Verify the SYSTIMAX name is upright on flat panel cover and on angled panel center cover before

snapping in place. These two covers can be installed upside down. Side covers on angled panel are

interchangeable and are not side specific.

www.commscope.com

860509975

Issue 2, December 2012

Page 3 of 5

Step 2 –Assemble and Install Rear Cable Manager

1. Attach the four cable troughs onto bar as shown and insert four hook-and-loop straps into slots in cable

troughs.

Cable bar

Mounting slot

2. Attach cable bar to rear of panel as shown. For 48-port panels, two cable bars are provided.

860509975

Instruction Sheet www.commscope.com

Page 4 of 5

Step 3 – Populate Panel with Outlets and Connect Ground

Hex nut with lock washer

Cables

Outlets

Grounding lug

1. Connect cables to outlets per instructions provided with the individual outlets.

2. Populate panel with outlets and route cabling as shown. Secure cables using the hook-and-loop straps

provided.

3. Use one of two grounding lug connections provided on rear of panel and hex nut with lock washer to ground

the panel per approved local practices. Tighten hex nut from 10 to 13-in-lbs (1.1 to 1.5 Nm).

Step 4 – Install Bezel Labels

Label

Label retainer area

1. Peel backing paper from a label and place in the label retainer area as shown. Carefully apply one end of

the label on the retainer and work it onto the retainer surface. Labels can be written on prior to being

removed from the backing or after they have been applied to the bezels.

www.commscope.com

860509975

Issue 2, December 2012

Page 5 of 5

Step 5 – To Remove an Outlet from Panel

Locking tabs

Flat-blade

screwdriver

1. Insert a small, flat-blade screwdriver or other small, blunt-end tool in between locking tab and side of outlet

as shown to release it. Disengaging one tab will release outlet.

Note: Insertion of tool should release the tab, but if not, pivot tool slightly until tab releases. Locking tabs for

two outlets are adjacent to each other. Inserting a tool in space between tabs will not release either tab.

2. Remove outlet from rear of panel.

Step 6 – Removing Covers from Panel

1. When removing either the flat or angled panel side cover(s), grip cover on the top and bottom at the outside

edge where shown by arrows and pull forward. As cover tabs release, position fingers close to tabs to apply

further pulling force.

2. For angled panel only, remove both side covers from panel before removing center cover.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CommScope Kabel und Steckverbinder Handbücher

CommScope

CommScope FOSC-OC-3 Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HFA208 Series Merkblatt

CommScope

CommScope AMP NETCONNECT 553454-1 Bedienungsanleitung

CommScope

CommScope NOVUX SXT Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed Bedienungsanleitung

CommScope

CommScope FIBER INDEXING TERMINAL Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT 1933352 Series Bedienungsanleitung

CommScope

CommScope SCIL-B Bedienungsanleitung

CommScope

CommScope FOSC 450 A Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HFE810 Series Merkblatt

CommScope

CommScope FDH1204-24SE2 Bedienungsanleitung

CommScope

CommScope OSP-CLPFEC-LG Bedienungsanleitung

CommScope

CommScope LightCrimp Plus LC Bedienungsanleitung

CommScope

CommScope FD21206-48SRC Series Merkblatt

CommScope

CommScope PICABOND 60944-6 Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT MRJ21 1479452-1 Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HTC1006 Series Merkblatt

CommScope

CommScope HELIAX FiberFeed FDH1210-24SE2 Series Merkblatt

CommScope

CommScope FIST-RSKG-16 Bedienungsanleitung

CommScope

CommScope BUDI-S Bedienungsanleitung

CommScope

CommScope SYSTIMAX 360 iPatch 360-iP-G2-1U-LC-FX Bedienungsanleitung

CommScope

CommScope SYSTIMAX 360 iPatch... Bedienungsanleitung

CommScope

CommScope ETHERSEAL 1479563-2 Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HFT1206-24S49 Series Merkblatt

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung