Craftsman 113.169270 Bedienungsanleitung

Save This Manual

For Future Reference

SE_AI

MODEL NO.

113.169270

Serial

Number

Model and serial numbers

may be found on the rear

of the floor nozzle.

You should record both

model and serial numbers

in a safe place for future

use.

FOR YOUR

SAFETY:

READ ALL

INSTRUCTIONS

CAREFULLY

i k,.

CARPET/U OLSTERY

SHAMPOOE ATTACHMENT

-assembly

- operating

*repair parts

Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A.

Part NO. SP5507 Pri_ted if" ,J_/-

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST

SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.

This warranty applies only while this product is used in the United States.

This warranty gives you specific rights, and you may also have other rights

which vary from state to state.

SEARS, ROEBUCK AND CO., D/817 WA Hoffman Estates, IL 60195

iMPORTANT SAFETY iNSTRUCTiONS

.LAD,LL,.ST.UCT,ONS

WARNING: DocotattempttO operate

until you have read thoroughly and understan_

completely a_l instructions contained in this manual.

Failure to do so can result in accidents. Save OwneCs

Manual and review frequentJy for continuing safe

operation. Use only in compliance with your Wet/Dry

Vac Owners Manual.

DONOT ATTACH OR USE WITH A VACUUM

CLEANER INTENDED FOR DRY PICKUP ONLY. IT

COULD CAUSE ELECTRICAL SHOCK. YOU

COULD BEELECTROCUTED " _ :_"

DO NOT USE THIS SHAMPOOER WHERE WATER

PRESSURE iS GREATER THAN 110 :POUNDS PER

SQUARE INCH Higher pressures can break parts

and spray hot water onto=people and property. People

could be badly burned.

Use shampoo (non-foaming cleaning solution

concentrate) with a mix ratio between 60-1 and 40-1

Note: the mixing valve is designed to automatically

make this mixture for you. Additional shampoo may

be purchased in your local Sears store.

NEVER allow children to operate shampooer, nor

should they play with shampooer as a toy, Hot.water

could be sprayed onto people or property. People

coufd get tangled in hoses and fall.

WetiDry Vacs contain a float system which shuts off

the suction when the water picked up reaches a

predetermined level. To continue your cleaning, turn

off the vac, disconnect the power cord from electrical

outlet, empty the drum, reassemble and continue

cleaning. Follow instructions for your Wet/Dry Vac

whenever using it with this accessory.

Safety Signal Word s

DANGER: means if the safety information is not

followed someone will be seriously injured or kiffed.

WARNING: means if the safety information is Hot

fotlowed someone could be seriously injured or killed.

CAUTION: means if [he safety information is not

followed someone nlight be seriously injured or killed.

TABLE OF CONTENTS

WARRANTY INFORMATION .................................... 2

SAFETY INSTRUCTIONS ......................................... 2

UNPACKING AND CHECKING CARTON

CONTENTS ............................................................. 3

SHAMPOOER ASSEMBLY ....................................... 3

OPTIONAL UPHOLSTERY NOZZLE ........................ 4

VALVE ASSEMBLY ................................................... 4

OPE RATION .............................................................. 6

CLEANING AND CARE ............................................. 6

REPAIR PARTS ........................................................ 7

SAVE THESE INSTRUCTIONS

: : iI _ 2

Removeentirecontentsofcarton.Checkeachitem

againstthe Carton Contents LisL Notify your Sears

Store immediately if any parts are damaged or

missing.

Carton Contents List

Key

[

Desc riptio nQty.

Lower Wand ............................................. 1

Upper Wand ............................................. 1

Handle With Trigger .................................. 1

Floor Nozzle .............................................. 1

Upholstery Nozzle .................................... 1

Vacuum Hose .......................................... I

Braided Hose w/Fittings ............................ 1

Tubing-Solution ........................................ 1

Shampoo Tubing Fitting w/Check Valve...1

Shampoo Lid and Shampoo Tubing ......... 1

Mixing Valve ............................................. I

Faucet Adapter (A-1) ................................ 1

Faucet Adapter {k-2) ................................. t

Faucet Adapter (A-3) ................................ 1

Washer (G-l) ............................................. 1

Washer (G-2) ............................................ t

Washer (G-3) ............................................ 1

Nozzle Adapter ......................................... 1

Owner's Manual ........................................ t

Shampoo (bottle appearance may vary} ............ 1

Shampooer Assembly I I!'ll '

I llil Jl IIII!.... I Ir

I II]

Preparation: Prior to using shampooer, vacuum the

carpet to remove loose dirt.

1. Insert a 6' x 1-1/4" vacuum hose into the inlet of

your wet/de/vac.

2. Assemble s:hampooer wands together assuring

snap lock is in place.

3. Assemble the handle with trigger to the upper wand

assuring snap lock is in place.

4. Assemble handle with trigger and wands to vac

hose.

5:Attachfloornozzletothe owerwand assuring snap

lock is in ptace..

6.:Push solution tub ng onto the nipple of the nozzle.

Thread solution tubing nut onto threads of nozzle.

Snap p astic tubing into the retainer clips on

underside ot wands.

7":_Thread braided hose onto handle with trigger.

WAND

BRAIDED

HOSE

Optional Upholstery Nozzle r=

1. Snap on and turn to lock the nozzle adapter onto

handle with trigger.

2. Attach upholstery nozzle to handle with trigger,

assuring snap lock is }n place and that the

upholstery nozzle and nozzle adapter are pushed

together. HANDLE

TRIGGER

NOZZLE ADAPTER

UPHOLSTERY NOZZLE

Valve Assembly i

1. Select adapter that fits your: faucet from the kits

provided with the shampooer.

2. Thread faucet adapter to any externally or internally

threaded faucet.

NOTE: Most faucets have aerators or filter

screens that unscrew. Remove the aerator or

screen by using pliers, if necessary. To avoid

damage to the aerator or screen, wrap aerator

with tape. Be certain auxiliary washer is used with

adapter and that you are careful not to cross or

strip adapter threads. Match auxiliary washers

and adapters by shape;

3. Make sure check valve is snapped into the fitting

but moves freely (see diagram). Slide end of

shampoo tubing onto fitting with check valve and

attach fitting to bottom of mixing valve.

4. Attach braided hose to the mixing valve.

THREAD

_INTERNAL

==_ ======= THREAD

i ]

IAUXILIARY

__ WASHER

ADAPTER _------..-_

LOCKING _ _ MIXING VALVE

RING _

U.--r"--" '_ BRAIDED

HOSE

4FI'FI'ING

5. Slide mixing valve ontO=faUCet adapter, then push

locking ring in an upward motion to lock,

NOTE: The braided hose should be pointing in the

general direction of the area to be cleaned. PUSH |

LOCKING RiNG

DIRECTIONOF AREA

TO BE CLEANED

6. Adjust your faucet to cold. Check for leaks, if

present, tighten the area where the leak occurs.

Then, adjust your faucet between warm and hot.

Extremely hot water could damage components of

the shampooer.

DANGER

Ordinary tap water can be hot enough to

quickly cause bad burns if it leaks or sprays

onto someone. To avoid this, make sure

your hot water heater thermostat is set at

120°F or less. Ask a plumber or your

electric, gas, or fuel oil supplier for help.

Many companies provide this service at no

charge.

7. Set the bottle of shampoo in sink to avoid tipping

and remove bottle cap. (Retain cap to close bottle

after use).

NOTE: Additional shampoo may be purchased in

your local Sears store.

8. Ptace filter end of shampoo tubing into bottle of

cleaning solution. Thread aux ary cap onto

solution bottle.

9. Squeeze trigger on handle and start the flow of

solution. Place floor nozzle or upholstery nozzle in

sink and squeeze tdgger until cleaning solution is

observed in the spray from the nozzle.

FILTER _.

4t,./FAUCET

MIXING VALVE

iSHAMPOOTUBING

=_--_----AUXILIARYCAP

- SINK

Operation ...........

DANGER

This Carpet Shampoo Attachment is

intended to be used with a Craftsman

Wet/Dry Vac. Do not attach or use with a

vacuum cleaner intended for dry pickup only.

it could cause electrical shock. You could be

electrocuted.

5. When cteaning is complete, release water pressure

before disconnecting from the faucet, Turn faucet

"OFF", Squeeze the trigger until spray stops.

6. For maximum efficiency, empty drum frequently

and keep the inside of hose, wands, nozzle an(]

drum clean.

1. Connect wet/dry vac power cord to a convenient

wall outlet.

2, Turn wet/dry vac power switch on.

3, Place nozzle on area to be cleaned and squeeze

trigger to release spray of solution onto surface.

Pull nozzle towards you with a slight downward

pressure while releasing spray. Release the trigger

and return the nozzle to the point where you initially

placed the nozzle. Slowly pull nozzle over damp

surface and observe dirty solution being recovered,

4. For easy emptying, periodica!ly check the level of

waste solution in the vac drum. If level of solution is

approximately half full, then empty. To empty, turf,

power switch "OFF" and disconnect power cord

from outlet. Release the two latches and remove lid

from the drum. Empty drum and reassemble in the

reverse order.

Wet/dry vacs are equipped with an automatic float

which is activated when the level of recovered

solution reaches a predetermined level When this

level is reached you cannot recover any more

liquid. To continue, follow your vac instructions to

empty liquid from the canister.

\ \

\\\\\

Cleaning and Care I , , I

1. Proper care of the equipment, after you have

finished shampooing, will extend the life of the

shampooer. First, remove shampoo tubing from

mixing valve and shampoo bottle. Place floor

nozzle over sink or bathtub and spray for

approximately 60 seconds to dnse cleaning solution

from tubing.

2, Remove mixing valve from faucet. Thoroug_qty

clean mixing valve under hot water for 60 seconds

te remove any concentrate residue build up. While

cleaning mixing valve, be very careful not to 10se or

misplace the check valve located inside the

shampoo tubing fitting. (See illustration on the

bottom of page 4).

NOTE: Leave braided hose connected and thread

large nut back onto valve body. If you used one of

the adapters provided, return adapter and its

washer to the bag it came in for future use.

3. Rinse wands and wrap braided hose around c)eats

provided on straight wands. Snap mixing valve

onto braided hose with "C" shaded clip provided on

the mixing valve.

Repair Parts- __ i,, ,l!l!l, .... i, , J,i B

PARTS LiST FOR CARPET/UPHOLSTERY SHAMPOOER ATTACHMENT

MODEL NO. 113.169270

©©©

7 1

Always order by Part Number

Not by Key Number

iKEV PART

i NO. NO.

L820456

2 820455

3 820454

4 820839

5 820840

6 820461

7 820460

8 820459

9 820473

10 820465

11 821888

12 820462

13 820472

14 9-16929

-- SP5507

DESCRIPTION

Handle With Trigger

Upper Wand

Lower Wand

FJoor Nozzle

Upholstery Nozzle

Tubing-Solution

Braided Hose w/Fittings

Vacuum Hose

Upholstery Nozzle Adapter:

Mixing Valve

Shampoo Tubing Fitting

w/Check Valve

Shampoo Lid and Shampoo

Tubing

Loose Parts Bag

Containing:

Three Washers

Three Faucet Adapters

1 Shampoo

Owners Manual

"stock item'- May be secured through the hardware

department of most Sears stores.

SERVICE

MODEL NO.

113.169270

HOW TO ORDER

REPAIRPARTS

CA RPET/UPHO LSTERY

SHAMPOOER ATTACHMENT

Service is available by returning this carpet cleaner to

the nearest Sears Service Center/Department

throughout the United States.

Model and serial numbers may be found on the rear of

the floor nozzle,

A!I pads listed may be ordered from any Sears Service

Center and most Sears stores, If the parts you need are

not stocked locally, your order will be electronically

transmitted to a Sears Repair Parts Distribution Center

for handling.

PART NUMBER PART DESCRIPTION

MODEL NUMBER

] ] 3. ] 69270 NAME OF ITEM

Carpet/Upholstery

Shampooer Attachment

.... r, J

Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A.

Part NO, SP5507 Form No. SP5507-3 Printed }n USA 5,'93

Inhaltsverzeichnis

Andere Craftsman Staubsauger Handbücher

Craftsman

Craftsman CMXEVBCV430L Bedienungsanleitung

Craftsman

Craftsman 113.177690 Bedienungsanleitung

Craftsman

Craftsman 125.04267621-3 evolv Bedienungsanleitung

Craftsman

Craftsman 113.177790 Bedienungsanleitung

Craftsman

Craftsman 113.177825 Bedienungsanleitung

Craftsman

Craftsman 315.175980 Bedienungsanleitung

Craftsman

Craftsman 358.797290 Bedienungsanleitung

Craftsman

Craftsman 17789 - Wet/Dry Vac Advanced Cleaning... Bedienungsanleitung

Craftsman

Craftsman 113.170250 Bedienungsanleitung

Craftsman

Craftsman 113.177780 Bedienungsanleitung

Craftsman

Craftsman 17741 - 6 Gal. Wet-Dry VAC Bedienungsanleitung

Craftsman

Craftsman 113.177360 Bedienungsanleitung

Craftsman

Craftsman 17965 - 6 Gal. Wet/Dry Vac Bedienungsanleitung

Craftsman

Craftsman 315.177520 Bedienungsanleitung

Craftsman

Craftsman 113.177480 Bedienungsanleitung

Craftsman

Craftsman 113.178200 Bedienungsanleitung

Craftsman

Craftsman 315.177530 Bedienungsanleitung

Craftsman

Craftsman 113.177460 Bedienungsanleitung

Craftsman

Craftsman CMXEVCVVJC507P Bedienungsanleitung

Craftsman

Craftsman 125.38909 Bedienungsanleitung

Craftsman

Craftsman 113.177311 Bedienungsanleitung

Craftsman

Craftsman 125.38907 Bedienungsanleitung

Craftsman

Craftsman 338.17920 Bedienungsanleitung

Craftsman

Craftsman 17776 - Clean N Carry 4 Gal. Wet-Dry VAC Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung