Craftsman 113.170250 Bedienungsanleitung

fSave This Manual

for Future Reference

SEARS

owner's

manual

MODEL NO.

113.170250

Serial

Number

Model and serial

numbers may be found

on the side of the

detachable blower. You

should record both

model and serial

numbers in a safe

place for future use.

FOR YOUR

SAFETY

READ ALL

INSTRUCTIONS

CAREFULLY

_ J

CRRFTSMRN®

16 GALLON

WET/DRY VAC

WITH DETACHABLE

BLOWER

• assembly

•operating

•repair parts

k. j

Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A.

Part No. SP6464 Printed in U.S.A.

FULL ONE YEAR WARRANTY

ON CRAFTSMAN WET/DRY VACS

Ifwithin one year from the date of purchase, this Craftsman Wet/Dry Vac fails

due to a defect in material or workmanship, Sears will repair it, free of charge.

If this Craftsman Wet/Dry Vac is used for commercial or rental purposes,

this warranty coverage applies for only 90 days from date of purchase.

Warranty Service Is Available By Simply Contacting The Nearest Sears Ser

vice Center/department Throughout The United States.

This warranty applies only while this product is in the United States.

This warranty gives you specific legal rights, and you may also have other

rights which vary from state to state.

Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL 60179

IMPORTANT SAFETY INSTRUCTIONS

Safety is a combination of common

sense, staying alert and knowing how

your vac works. Read this manual to

understand the vac.

Safety Signal Words

DANGER: means ifthe safety information

is not followed someone will be seriously

injured or killed.

WARNING: means if the safety informa-

tion is not followed someone could be

seriously injured or killed.

CAUTION: means if the safety informa-

tion is not followed someone may be

injured.

When using your Wet/Dry Vac, follow

basic safety precautions including the fol-

lowing.

WARNING- To reduce

the risk of fire, electric shock, or

injury:

Read and understand this owner's manual

and all labels on the Wet/Dry Vac before

operating. Use only as described in this man-

ual. To reduce the risk of personal injury or

damage to Wet/Dry Vac, use only Sears

Craftsman recommended accessories.

Sparks inside the motor can ignite flam-

mable vapors or dust. To reduce the risk

of fire or explosion:

• Do not vacuum, or use this Wet/Dry Vac

near, flammable or combustible liquids,

gases, or explosive dusts like gasoline

or other fuels, lighter fluid, cleaners, oil-

based paints, natural gas, hydrogen,

coal dust, magnesium dust, grain dust,

or gun powder.

• Do not use Wet/Dry Vac as a sprayer.

Do not vacuum anything that is burning or

smoking, such as cigarettes, matches, or

hot ashes.

Do not vacuum fireplace soot or ash. This

is a very fine dust which will not be cap-

tured by the filter and may cause damage.

To reduce the risk of health hazards from

vapors or dusts, do not vacuum toxic

materials.

Do not use or store near hazardous materials.

To reduce the risk of electric shock, do not

expose to rain. Store indoors.

Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

Do not use this Wet/Dry Vac with a torn fil-

ter or without the filter installed except for

vacuuming liquids as described in the

operation section of this manual.

Do not leave Wet/Dry Vac when plugged

in. Unplug from outlet when not in use and

before servicing. Turn off Wet/Dry Vac

before unplugging.

WARNING: To reduce the risk of fire

or electric shock, do not run vac

unattended.

To reduce the risk of injury from acciden-

tal starting, unplug power cord before

changing or cleaning filter.

Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

Do not use with damaged cord, plug or

other parts. Ifyour Wet/Dry Vac is not

working as it should, has missing parts,

has been dropped, damaged, left out-

doors, or dropped into water, return it to a

Sears Service Center.

Do not pull or carry by cord, use cord as

handle, close a door on cord, or pull cord

around sharp edges or corners. Do not

run Wet/Dry Vac over cord. Keep cord

away from heated surfaces.

Do not handle plug or the Wet/Dry Vac

with wet hands.

Do not put any object into ventilation

openings. Do not vacuum with any venti-

lation openings blocked; keep free of dust,

lint, hair or anything that may reduce air

flow.

Keep hair, loose clothing, fingers, and all

parts of body away from openings and

moving parts.

To reduce the risk of falls, use extra care

when cleaning on stairs.

This Wet/Dry Vac is double-insulated,

eliminating the need for a separate

grounding system. Use only identical

replacement parts. Read the instructions

for Servicing Double-Insulated Wet/Dry

Vacs before servicing.

Use this Wet/dry Detachable Blower Vac

as described in this manual.

When using as detached blower:

• Turn unit off before setting on ground or

releasing grasp from handle.

• Do not use on wet surfaces, electric

shock could occur.

• Direct air discharge only at work area.

• Do not direct air at bystanders.

• Keep children away when blowing.

• Do not use blower for any job except

blowing dirt and debris.

Observe the following warnings that

appear on the motor housing of your Wet/

Dry Vac.

_ OUBLE INSULATED

GROUNDINGNOTREQUIRED

WHEN SERVICING USEONLY

IDENTICALREPLACEMENTPARTS

WARNING: To reduce the risk of

electric shock- do not expose to

rain-store indoors.

WARNING: For your own safety,

read and understand owner's man-

ual. Do not pick up hot ashes, coals,

toxic, flammable or other hazard-

ous materials. Do not use around

explosive liquids or vapors.

SAVE THESE INSTRUCTIONS

The operation of any utility vac or blower

can result in foreign objects being blown

into the eyes, which can result in severe

eye damage. Always wear safety goggles

complying with ANSI Z87.1 (shown on

package) before commencing operation.

Safety Goggles are available at Sears

retail stores.

WEAR YOUR

To reduce the risk of hearing damage,

wear ear protectors when using the vac

for extended hours or when, using it in a

noisy area.

For dusty operations, wear dust mask.

Use only extension cords that are rated

for outdoor use. Extension cords in poor

condition or that are too small in wire size

can pose fire and shock hazards. When

using an extension cord, be sure it is in

good condition. Using any extension cord

will cause some loss of power. To keep

the loss to a minimum, use the following

table to choose the minimum wire size

extension cord.

Extension Gauge

Cord Length (A.W.G.)

0-50 Ft. 14

50-100 Ft. 12

Introduction

This Wet/Dry Vac is intended for house-

hold use only.

IMPORTANT NOTE

Please Read Carefully

Static Shocks Are Common - In dry

areas or when the relative humidity of the

air is low. To reduce the frequency of

static shocks in your home the best rem-

edy is to add moisture to the air with a

console humidifier.

Table of Contents

Item Page

Warranty Information ............................. 2

Safety Instructions ................................. 2

Introduction ............................................ 4

Unpacking and Checking

Carton Contents ............................. 4

Assembly ............................................... 5

Operation ............................................... 9

Maintenance ........................................ 13

Repair Parts ........................................ 16

Unpacking and Checking Carton Contents m

Remove entire contents of carton. Check

each item against the Carton Contents List.

Some units may include accessories not

shown. Notify your Sears Store immedi-

ately if any parts are damaged or missing.

Carton Contents List

Key Description ............................ Qty.

A 16 Gallon Wet/Dry Vac ............... 1

B Hose .......................................... 1

C Blower Adapter .......................... 1

D Diffuser ...................................... 1

E Blower Nozzle ............................ 1

F Utility Nozzle .............................. 1

G Wet Nozzle ................................. 1

H Car Nozzle ................................. 1

J Extension Wands ....................... 2

K Accessory Caddy ....................... 1

L Float ........................................... 1

M Filter Cage ................................. 1

N Filter (Red Stripe) ...................... 1

P Filter Plate .................................. 1

R Filter Nut .................................... 1

S Single Wheel Caster .................. 2

T Wheel Assembly ........................ 2

U Owners Manual .......................... 1

S K

Accessory Caddy Assembly

1. Unlatch the drum latches on the front

and rear of unit. The drum latches hold

the lid onto the drum. Lift the lid off the

drum. Place the lid upside down on a

clean smooth surface.

2. Flip the drum upside down on the floor.

3. Take the accessory caddy and position

it on the vac drum. The open end of

horseshoe shaped caddy should be

positioned under the drain cap.

4. Slide the caddy down onto the drum,

the open end of the caddy has two

dovetail slides that will press into the

molded area of the drum. The caddy

will press onto the drum until it rests

against the first step of the drum. The

bottom edge of the caddy will be even

with the bottom edge of the vac drum. If

it is not even with the bottom of the

drum, tap the edge until it is flush with

the drum bottom. The tab lock located

at the rear of the caddy will latch into

the recessed area at the rear of the vac

drum.

Accessory Dove

Caddy Tail

z'_'_/ Drain

/Cap

toa&

To Install the WheelslCasters

1. Locate the two 5-1/4" wheel assemblies

and the single wheel casters.

2. Insert the single wheel casters into the

bottom of the accessory caddy as

shown (2 places).

3. Push on the caster until the end of the

caster stem is inserted all the way into

the socket. You will be able to hear the

end of the caster snap into the socket of

the caddy. The caster will rotate easily

when positioning is correct.

4. Position the dovetail section of one of

the wheel assemblies into the acces-

sory caddy as illustrated. Tap the wheel

support of the assembly with a soft mal-

let if necessary. Repeat for the second

wheel assembly.

Wheel _...._

Support

5. Flip the drum/caddy assembly upright

with the wheels of the caddy resting on

the floor.

NOTE: When emptying debris from the

wet/dry drum, it is not necessary to

remove the vac caddy.

Float/Cage Assembly

WARNING: For your own safety,

never connect plug to power source

outlet until all assembly steps are

complete and you have read and

understood the safety and operation

instructions. Do not operate vac with

any parts damaged or missing.

1. Remove the detachable blower from the

power head assembly by pressing

down on the power head latch beneath

the carry handle of the detachable

blower. Set the detachable blower off to

the side. Place lid upside down on

drum.

2. Locate the float and filter cage. (The

float is inside the loose parts bag.)

3. Place the float over the center opening

in the lid with the words "This side

towards lid" laying face down over the

hole. (See illustration.)

WARNING: To reduce the risk of

personal injury or damage to vac be

sure to keep hands, fingers, or any

other foreign objects out of the cen-

ter opening when assembling the

float.

4. Line up the filter cage tabs as shown

with the slots in the center ring of the lid

assembly. Push on the filter cage until

the tabs snap into the slots for a secure

fit.

NOTE: Iffilter cage needs to be removed,

because the float is placed in the wrong

way, use a flat blade screwdriver and

insert the blade near one of the tabs

between the filter cage and the center ring

of the lid. Pry the tab out of the slot. Tilt

the cage and lift away from the lid. To

replace, follow float/cage assembly

instructions.

Detachable

Dru! Power Head

Latch Latch Lid Asm.

_'_ Filter

/Cage

#= L Tabs 131

___O:e:t End

Slots (3)

Filter Assembly

1. Carefully slide the filter over the filter

cage, sliding it over the center ring cov-

ering the 3 slots until the filter stops

against the lid.

2. Place the hole in the filter plate over

threaded screw of the filter cage.

3. Gently push on the filter plate to seat

the rubber ring of the filter inside the cir-

cular channel of the filter plate.

4. Place filter nut onto threaded screw and

tighten it down. Finger tighten only.

NOTE: Lever of filter nut should be away

from plate as shown.

IMPORTANT: Do not overtighten as this

may deform or crack the filter plate, filter

cage or the filter.

NOTE: Your filter has a red stripe that

matches an in-store disptayer. When you

visit your local Sears store, just remember

the color of your stripe for the correct size

filter.

Vac Assembly

1. Locate the lid assembly and the drum/

caddy assemblies (assembled earlier).

2. Position the lid assembly with the inlet

of the unit located in line with the drain

cap and the drum label on the vac.

Allow the assembly to rest on the vac

drum.

3. Rotate both latches down until you hear

the latches snap over the lip of the

drum.

NOTE: For best appearance of the unit,

the inlet of the vac should be located

above the drain.

Cord Storage

Simply wrap the power cord around the lid

assembly and snap the connector on the

plug to a wrap of the cord.

Latch Latch

Positioning Detachable Blower

(Power Head Assembly)

1. Locate the detachable blower of your

Craftsman wet/dry vac.

2. On top of the blower (opposite the han-

dle side of the blower); there is molded

plastic lead that is used to assist

assembling the unit. Position the lead

into the indented area above the label.

Molded

Plastic Lead

ndented

Area

3. Rotate the detachable blower down

until the travel of the unit stops.

4. Lightly press down on the carry handle

of the detachable blower until the power

head latch engages the blower. The

detachable blower is now latched to the

lid assembly.

Power Head

Latch

Your new wet/dry vac is ready for use.

With the wet/dry vac completely assem-

bled and ready for use, insert the push but-

ton end of the hose assembly into the inlet

of the vac. The hose should snap into

place. To remove the hose from the vac

press the release button in the hose

assembly and pull the hose out of the vac

inlet.

Release

Button Press and

Pull

Operation

WARNING

To reduce the risk of fire or explosion, do not operate this vac in areas with

flammable gases or flammable vapors such as lighter fluid, cleaners, oil-base

paints, gasoline, alcohol or explosive dust such as coal, magnesium, grain or

gun powder in the air. Do not vacuum explosive dust, flammable or combusti-

ble liquids or hot ashes. Do not use this vac as a sprayer. To reduce the risk of

health hazards from vapors or dusts, do not vacuum toxic materials. To reduce

the risk of electrical shock do not expose to rain. Store vac indoors. Unplug

power cord before changing or cleaning filter or emptying the dust drum.

CAUTION: To reduce the risk of hear-

ing damage wear ear protectors

when using the vac or blower for

extended hours or when using it in a

noisy area. The operation of any util-

ity vac or blower can result in foreign

objects being blown into the eyes,

which can result in severe eye dam-

age. Always wear safety goggles

complying with ANSI Z87.1 (shown

on Package) before commencing

operation. Safety Goggles are avail-

able at Sears retail stores.

If the noise level of this unit is too loud,

purchase the Craftsman Noise Muffler;

accessory number 9-16991 found in

Sears retail stores or the Sears Power

and Hand Tool Catalog.

To reduce the risk of electric shock, this

appliance has a polarized plug (one blade

is wider than the other). This plug will fit in

a polarized outlet only one way. Ifthe plug

does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a quali-

fied electrician to install the proper outlet.

Do not change the plug in any way.

NOTE: When using the unit in the vacu-

uming mode, always insert the air diffuser

in the exhaust port on the detachable

blower. This breaks up the direct flow of

air and diffuses it.

Vacuuming Dry Materials

1. The filter must be in correct position at

all times to reduce the risk of leaks and

possible damage to vac.

2. When using your vac to pick up very

fine dust, it will be necessary for you to

empty the drum and clean the filter at

more frequent intervals to maintain

peak vac performance.

NOTE: A dry filter is necessary to pick up

dry material. If you use your vac to pick up

dust when the filter is wet, the filter will

clog quickly and be very difficult to clean.

3. If your filter is wet but you need to use

the vac to pick up dry material, you can

quickly dry the filter by running the vac

without hose attached for about 10 min-

utes. The clean air rushing through the

vac will help dry the filter.

The optional Craftsman Fine Particle Fil-

ter, stock number 9-17916 will do a bet-

ter job stopping the very fine particles

than the 9-17816 filter. This filter will stop

99.99% of all particles as small as one

micron.

Vacuuming Liquids

1.When picking up small amounts of liq-

uid the filter may be left in place.

2. When picking up large amounts of liq-

uid we recommend that the filter be

removed. If the filter is not removed, it

will become saturated and misting may

appear in the exhaust.

3.After using the vac to pick up liquids,

the filter must be dried to reduce the

risk of possible mildew and damage to

the filter.

Operation (continued)

4. When the liquid in the drum reaches a

predetermined level, the float mecha-

nism will rise automatically to cut off air-

flow. When this happens, turn off the

vac, unplug the power cord, and empty

the drum. You will know that the float

has risen because vac airflow ceases

and the motor noise will become higher

in pitch, due to increased motor speed.

IMPORTANT: To reduce the risk of dam-

age to the vac do not run motor with float

in raised position.

Emptying Dust Drum

WARNING: To reduce the risk of

injury from accidental starting,

unplug power cord before emptying

the drum.

1. To remove the lid to empty contents of

the dust drum, simply lift the two drum

latches at the front and rear of the dust

drum and lift the lid assembly up and off

the dust drum and set to the side.

NOTE: Do not pick up the lid assembly

by lifting on the handle to the detach-

able blower. Lift the lid assembly by the

latches. This will ensure that the

detachable blower and the lid will not

separate during removal of the lid

assembly.

2. Lay the lid assembly upside down on a

clean dry area while emptying the drum

or changing the filter.

3. Dump the drum contents into the

proper waste disposal container.

Latch

4. If the contents are liquid, you may dis-

pose by using the drain provided in the

drum for easy emptying. Simply

unscrew the drain cap and allow the liq-

uid to drain completely out of the vac

drum.

WARNING: To reduce the risk of

back injury or falls, do not lift a vac

heavy with liquid or debris. Scoop or

drain enough contents out to make

the vac light enough to lift comfort-

ably.

Inhaltsverzeichnis

Andere Craftsman Staubsauger Handbücher

Craftsman

Craftsman 125.12009 Bedienungsanleitung

Craftsman

Craftsman 113.177600 Bedienungsanleitung

Craftsman

Craftsman 113.177135 Bedienungsanleitung

Craftsman

Craftsman CMCV002 Bedienungsanleitung

Craftsman

Craftsman 113.177370 Bedienungsanleitung

Craftsman

Craftsman CMXEVCVVBVA1612 Bedienungsanleitung

Craftsman

Craftsman 113.177260 Bedienungsanleitung

Craftsman

Craftsman 125.12009 Bedienungsanleitung

Craftsman

Craftsman 113.178060 Bedienungsanleitung

Craftsman

Craftsman 113.177000 Bedienungsanleitung

Craftsman

Craftsman 113.170170 Bedienungsanleitung

Craftsman

Craftsman CMXEVBCV430L Bedienungsanleitung

Craftsman

Craftsman CMXEVCVVJH1612 Bedienungsanleitung

Craftsman

Craftsman 113.170660 Bedienungsanleitung

Craftsman

Craftsman 113.177145 Bedienungsanleitung

Craftsman

Craftsman 113.169270 Bedienungsanleitung

Craftsman

Craftsman 113.170330 Bedienungsanleitung

Craftsman

Craftsman 113.176120 Bedienungsanleitung

Craftsman

Craftsman CMCVH001 Bedienungsanleitung

Craftsman

Craftsman 17765 - 5.0 Peak HP Wet/Dry Vac Bedienungsanleitung

Craftsman

Craftsman 125.12005 Bedienungsanleitung

Craftsman

Craftsman 125.12002 Bedienungsanleitung

Craftsman

Craftsman 113.177460 Bedienungsanleitung

Craftsman

Craftsman CMXEVBE176120 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung